Ali Faezian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ali Faezian has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Masoud Hashemi Shahraki
Department of Food Science and Technology, Gorgan University of Agricultural Science and Natural Resources, Beheshti Avenue, Gorgan 49138-15739, Iran
5 shared publications Abdolmajid Maskooki
Department of Food Processing; Research Institute of Food Science and Technology (RIFST); Mashhad Iran
3 shared publications- Samira Yeganehzad
Research Institute of Food Science and Technology
3 shared publications - Abdolmajid Maskooki
Department of Food Processing, Research Institute of Food Science and Technology (RIFST), P.O. Box 91735-147, Km 12, Asian Highway, Mashhad, Iran, Tel. +98 9381321295; Fax: +98 511 5003150
2 shared publications - Hashem Ahmadi Tighchi
Department of Mechanical Engineering, Faculty of Engineering, Ferdowsi University of Mashhad 4 , Mashhad
2 shared publications Zohreh Baratian Ghorghi
Department of Food Sensory and Cognitive Science, Research Institute of Food Science and Technology (RIFST), Mashhad, Iran
2 shared publications
Latest Publications
- Open Access
- 7 January 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-15
Numerical simulation and experimental validation of the oleogel formation from grape seed oil and beeswax
This study focuses on numerical modeling of the oleogelation process using grape seed oil and beeswax and its validation using experimental approach. The main goal is to investigate how the cooling rate affects this process. The necessary physical and thermal properties of the oleogel for modeling were determined through experiments. Additionally, differential scanning calorimetry was used to characterize phase transitions. The apparent heat capacity method was applied in the numerical modeling to simulate the phase change process, and the energy equation was solved using the finite element method. The numerical model demonstrated a maximum relative error of 5.4%, indicating a strong agreement between the numerical results and experimental data. After validating the numerical model, five different cooling rates were investigated. The findings showed that oleogelation begins near the bottom boundary of the setup and then propagates toward the center. Furthermore, the fraction of the total time required for the phase change to complete varied between 0.35 and 0.04 as the cooling rate decreased. This indicates that slower cooling rates provide more time for heat transfer, allowing for more thorough gelation and completing the phase transition in a smaller fraction of the total time. The proposed model can save time and costs while delivering accurate data on creating a beneficial oleogel.
- 7 January 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-15
Open AccessNumerical simulation and experimental validation of the oleogel formation from grape seed oil and beeswax
This study focuses on numerical modeling of the oleogelation process using grape seed oil and beeswax and its validation using experimental approach. The main goal is to investigate how the cooling rate affects this process. The necessary physical and thermal properties of the oleogel for modeling were determined through experiments. Additionally, differential scanning calorimetry was used to characterize phase transitions. The apparent heat capacity method was applied in the numerical modeling to simulate the phase change process, and the energy equation was solved using the finite element method. The numerical model demonstrated a maximum relative error of 5.4%, indicating a strong agreement between the numerical results and experimental data. After validating the numerical model, five different cooling rates were investigated. The findings showed that oleogelation begins near the bottom boundary of the setup and then propagates toward the center. Furthermore, the fraction of the total time required for the phase change to complete varied between 0.35 and 0.04 as the cooling rate decreased. This indicates that slower cooling rates provide more time for heat transfer, allowing for more thorough gelation and completing the phase transition in a smaller fraction of the total time. The proposed model can save time and costs while delivering accurate data on creating a beneficial oleogel.
- Open Access
- 14 June 2023
- Published by MDPI AG in Colloids and Interfaces
- Vol. 7 (2) , 47
Examination of a Theoretical Model for Drainage of Foams Prepared from Licorice Root Extract Solution
The root of the licorice plant (Glycyrrhiza glabra) is rich in natural surfactants, called saponins. The beneficial properties of this plant have led to different applications, including its use as a foaming agent. In this research, a theoretical model and its validity are discussed for the liquid drainage of foams made from licorice root extract solutions. After stating the important characteristics in the free drainage of foam, a relationship of the drained liquid volume based on effective parameters was obtained via a simplification of the governing equation. The theoretical model is applied to experimental foam drainage data measured at different concentrations of licorice root extract solutions. A comparison of theoretical and experimental results shows good agreement for the volume of drained liquid as a function of time. The characteristics obtained from the combination of effective parameters allows for a quantification of the drainage rate. In addition, the drainage rate at the beginning of the foam decay process, as a measure of stability, can be estimated using measurable properties.
- 14 June 2023
- Published by MDPI AG in Colloids and Interfaces
- Vol. 7 (2) , 47
Open AccessExamination of a Theoretical Model for Drainage of Foams Prepared from Licorice Root Extract Solution
The root of the licorice plant (Glycyrrhiza glabra) is rich in natural surfactants, called saponins. The beneficial properties of this plant have led to different applications, including its use as a foaming agent. In this research, a theoretical model and its validity are discussed for the liquid drainage of foams made from licorice root extract solutions. After stating the important characteristics in the free drainage of foam, a relationship of the drained liquid volume based on effective parameters was obtained via a simplification of the governing equation. The theoretical model is applied to experimental foam drainage data measured at different concentrations of licorice root extract solutions. A comparison of theoretical and experimental results shows good agreement for the volume of drained liquid as a function of time. The characteristics obtained from the combination of effective parameters allows for a quantification of the drainage rate. In addition, the drainage rate at the beginning of the foam decay process, as a measure of stability, can be estimated using measurable properties.
- 16 February 2023
- Published by Elsevier in Food Hydrocolloids
- Vol. 140
Fabrication of novel hybrid gel based on beeswax oleogel: Application in the compound chocolate formulation
- 16 February 2023
- Published by Elsevier in Food Hydrocolloids
- Vol. 140
Fabrication of novel hybrid gel based on beeswax oleogel: Application in the compound chocolate formulation
- 1 February 2019
- Published by Elsevier in Chemical Engineering Science
- Vol. 195, 631-641
A simplified model to describe drainage of egg white powder foam containing additives
- 1 February 2019
- Published by Elsevier in Chemical Engineering Science
- Vol. 195, 631-641
A simplified model to describe drainage of egg white powder foam containing additives
- 1 May 2017
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 91, 39-50
Slug and bubble flows in a flat sheet ultrafiltration module: Experiments and numerical simulation
- 1 May 2017
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 91, 39-50
Slug and bubble flows in a flat sheet ultrafiltration module: Experiments and numerical simulation
- Open Access
- 1 September 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (45) , 21173-21181
Effect of soluble and insoluble gas bubbling methods on ultrafiltration fouling control
Fouling phenomenon is well known as a main obstacle in membrane separation technology. In this study, the effects of bubbling with various hydrodynamic factors and gas–liquid solubility were evaluated on fouling control and permeation flux in ultrafiltration of skimmed milk solution. Direct gas injection and carbonated feed, as a new bubbling method, were used for bubbling. In the direct gas injection technique, various two-phase flow patterns (slug and bubble), gas flow rates, and bubbling modes (continuous and intermittent) were investigated during a cross-flow ultrafiltration. The results showed that the both of gas bubbling methods improved the permeation flux during 30-min filtration. The permeation flux was enhanced up to 72 and 40% by direct injecting of N2 and CO2, respectively, while it was only enhanced up to 58% with carbonated feed. The evaluation of hydrodynamic resistance of membranes indicated that the gas bubbling by carbonated feed was more effective on the fouling resistance, while the cake resistance was affected by the gas injection during infiltration. In addition, the slug flow pattern was more effective than the bubble flow pattern on decline of membrane fouling. In the slug flow pattern, the permeate flux increased when medium flow rate was applied. Furthermore, ultrafiltration performance was improved using the intermittent gas bubbling mode. This study indicated that slug flow pattern with insoluble gas has a higher performance than the other ones in preventing fouling and flux enhancement during ultrafiltration processing.
- 1 September 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (45) , 21173-21181
Open AccessEffect of soluble and insoluble gas bubbling methods on ultrafiltration fouling control
Fouling phenomenon is well known as a main obstacle in membrane separation technology. In this study, the effects of bubbling with various hydrodynamic factors and gas–liquid solubility were evaluated on fouling control and permeation flux in ultrafiltration of skimmed milk solution. Direct gas injection and carbonated feed, as a new bubbling method, were used for bubbling. In the direct gas injection technique, various two-phase flow patterns (slug and bubble), gas flow rates, and bubbling modes (continuous and intermittent) were investigated during a cross-flow ultrafiltration. The results showed that the both of gas bubbling methods improved the permeation flux during 30-min filtration. The permeation flux was enhanced up to 72 and 40% by direct injecting of N2 and CO2, respectively, while it was only enhanced up to 58% with carbonated feed. The evaluation of hydrodynamic resistance of membranes indicated that the gas bubbling by carbonated feed was more effective on the fouling resistance, while the cake resistance was affected by the gas injection during infiltration. In addition, the slug flow pattern was more effective than the bubble flow pattern on decline of membrane fouling. In the slug flow pattern, the permeate flux increased when medium flow rate was applied. Furthermore, ultrafiltration performance was improved using the intermittent gas bubbling mode. This study indicated that slug flow pattern with insoluble gas has a higher performance than the other ones in preventing fouling and flux enhancement during ultrafiltration processing.
- 6 May 2016
- Published by Wiley in Journal of Food Processing and Preservation
- Vol. 41 (2) , e12795
Ultrafiltration of Cherry Concentrate Under Ultrasound with Carbonated Feed as a New Fouling Control Method
- 6 May 2016
- Published by Wiley in Journal of Food Processing and Preservation
- Vol. 41 (2) , e12795
Ultrafiltration of Cherry Concentrate Under Ultrasound with Carbonated Feed as a New Fouling Control Method
- Open Access
- 25 January 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (51) , 24278-24287
Flux improvement of ultrafiltration membranes using ultrasound and gas bubbling
This study investigated the effects of ultrasound (US) and gas bubbling (GB) on permeate flux and membrane fouling. The ultrafiltration process of 1% skimmed milk was performed under various ultrasonic frequencies (37, 80 kHz, and tandem), irradiation modes (pulsed and sweeping), two-phase flow patterns (bubble and slug), and gas flow rates. The results showed that the US treatment improves the permeate flux up to 180%. The highest cleaning effect was obtained in the pulsed mode at 37 kHz. In the tandem frequency, the results showed that the fouling percentage significantly decreased with reduction in the frequency switching time. The GB injection treatment improved the mean of permeate flux up to 72% after 30 min. The slug pattern at medium gas flow rate was more effective than the other treatments. Best result was achieved in combination of the US (pulsed mode—37 kHz) and the GB (slug pattern—medium flow rate). In this condition, the permeate flux was significantly improved up to 384% in comparison with the control. Furthermore, the hydrodynamic resistance results showed the higher ability of the US in cleaning of membrane pores during ultrafiltration.
- 25 January 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (51) , 24278-24287
Open AccessFlux improvement of ultrafiltration membranes using ultrasound and gas bubbling
This study investigated the effects of ultrasound (US) and gas bubbling (GB) on permeate flux and membrane fouling. The ultrafiltration process of 1% skimmed milk was performed under various ultrasonic frequencies (37, 80 kHz, and tandem), irradiation modes (pulsed and sweeping), two-phase flow patterns (bubble and slug), and gas flow rates. The results showed that the US treatment improves the permeate flux up to 180%. The highest cleaning effect was obtained in the pulsed mode at 37 kHz. In the tandem frequency, the results showed that the fouling percentage significantly decreased with reduction in the frequency switching time. The GB injection treatment improved the mean of permeate flux up to 72% after 30 min. The slug pattern at medium gas flow rate was more effective than the other treatments. Best result was achieved in combination of the US (pulsed mode—37 kHz) and the GB (slug pattern—medium flow rate). In this condition, the permeate flux was significantly improved up to 384% in comparison with the control. Furthermore, the hydrodynamic resistance results showed the higher ability of the US in cleaning of membrane pores during ultrafiltration.
- 28 December 2015
- Published by Wiley in Journal of Food Process Engineering
- Vol. 40 (1)
Hollow Fibers Filtration and Cleaning Processes Under Ultrasound and Gas Bubbling Combination
Fouling is one of the main obstacles to filtration process. In this study, the effects of gas bubbling by carbonated feed, gas bubbling by direct injection of CO2 (GB‐DI‐CO2) and N2 (GB‐DI‐N2) and ultrasound (US) were evaluated on flux enhancement during milk solution ultrafiltration and flux recovery during cleaning process of fouled hollow fibers membrane module. Results showed that the US and gas bubbling (GB) treatments significantly enhanced the performance of both ultrafiltration and cleaning processes, however, the effect of GB‐DI‐CO2 was not considerable. The best results were achieved when the GB‐DI‐N2 treatment was applied with US treatment in filtration and cleaning process, under this treatment, the permeation flux was remarkably enhanced up to 288.57% during ultrafiltration as well as the fouling percentage was reduced to 15.55% after cleaning the fouled membrane. Furthermore, the US was more effective than the GB during cleaning process.Practical Applications: Filtration process is faced to flux decline as a result of fouling. The ultrasound at low frequency and liquid–gas two phase flow can affect the concentration polarization and cake layer significantly. The combination of these techniques can be used as an effective methods to handle the fouling and flux decline. Also artificial neural networks model is able to predict the flux permeation of hollow‐fibers filtration under ultrasound and gas bubbling combination as a complex condition practically.
- 28 December 2015
- Published by Wiley in Journal of Food Process Engineering
- Vol. 40 (1)
Hollow Fibers Filtration and Cleaning Processes Under Ultrasound and Gas Bubbling Combination
Fouling is one of the main obstacles to filtration process. In this study, the effects of gas bubbling by carbonated feed, gas bubbling by direct injection of CO2 (GB‐DI‐CO2) and N2 (GB‐DI‐N2) and ultrasound (US) were evaluated on flux enhancement during milk solution ultrafiltration and flux recovery during cleaning process of fouled hollow fibers membrane module. Results showed that the US and gas bubbling (GB) treatments significantly enhanced the performance of both ultrafiltration and cleaning processes, however, the effect of GB‐DI‐CO2 was not considerable. The best results were achieved when the GB‐DI‐N2 treatment was applied with US treatment in filtration and cleaning process, under this treatment, the permeation flux was remarkably enhanced up to 288.57% during ultrafiltration as well as the fouling percentage was reduced to 15.55% after cleaning the fouled membrane. Furthermore, the US was more effective than the GB during cleaning process.Practical Applications: Filtration process is faced to flux decline as a result of fouling. The ultrasound at low frequency and liquid–gas two phase flow can affect the concentration polarization and cake layer significantly. The combination of these techniques can be used as an effective methods to handle the fouling and flux decline. Also artificial neural networks model is able to predict the flux permeation of hollow‐fibers filtration under ultrasound and gas bubbling combination as a complex condition practically.