Julian Praß
Julian Praß has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Johannes Weber
Institute for Factory Automation and Production Systems (FAPS), Friedrich-Alexander University of Erlangen-Nürnberg, Germany
5 shared publicationsJörg Franke
Institute for Factory Automation and Production Systems (FAPS), Friedrich-Alexander University of Erlangen-Nürnberg, Germany
4 shared publicationsAndreas Renz
Institute of Process Machinery and Systems Engineering
3 shared publicationsStefan Becker
Erlangen Germany Cauerstraße 4 91058
3 shared publicationsThomas Braun
Institute for Factory Automation and Production Systems (FAPS), Friedrich-Alexander University of Erlangen-Nürnberg, Germany
2 shared publicationsA. Metelkin
1 shared publication
Latest Publications
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Advanced Engineering Forum
- Vol. 19, 43-49
Experimental Investigation of a Friction Ventilator
Standard decentralized ventilation systems typically consist of two ventilators for inlet and exhaust air and a heat exchanger for the heat recovery. A recently developed device, a so called friction ventilator, combines these three elements into a single functional element. The ventilator consists of circular plates which are rotating centrally in between the inlet and the outlet duct of a ventilation system and generate a countercurrent flow in the two ducts. Furthermore, the discs act as a rotating heat exchanger between the two air flows. To increase understanding of the energy transfer from the rotating discs to the flow an experimental investigation on the effect of different rotor geometries was conducted. The study showed an interesting influence of the hub diameter on the characteristic curves with a higher pressure difference for an increase in diameter. The results of the heat recovery measurement however were only mildly affected by the hub geometry. Here the distance between the discs, the rotational speed of the discs and the volumetric flow seemed to have the greatest effect on heat recovery.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Advanced Engineering Forum
- Vol. 19, 43-49
Experimental Investigation of a Friction Ventilator
Standard decentralized ventilation systems typically consist of two ventilators for inlet and exhaust air and a heat exchanger for the heat recovery. A recently developed device, a so called friction ventilator, combines these three elements into a single functional element. The ventilator consists of circular plates which are rotating centrally in between the inlet and the outlet duct of a ventilation system and generate a countercurrent flow in the two ducts. Furthermore, the discs act as a rotating heat exchanger between the two air flows. To increase understanding of the energy transfer from the rotating discs to the flow an experimental investigation on the effect of different rotor geometries was conducted. The study showed an interesting influence of the hub diameter on the characteristic curves with a higher pressure difference for an increase in diameter. The results of the heat recovery measurement however were only mildly affected by the hub geometry. Here the distance between the discs, the rotational speed of the discs and the volumetric flow seemed to have the greatest effect on heat recovery.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Advanced Engineering Forum
- Vol. 19, 35-42
Numerical Investigation of a Friction Ventilator for Different Geometrical Setups
Conventional ventilation systems with heat recovery used for building aeration exhibit characteristic disadvantages arising from their operating principle such as noise generation from bladed ventilators or remarkable pressure losses generated by heat exchangers. A novel concept that combines ventilators and heat exchanger in one compact friction ventilator that rotates in two separated ducts producing two opposed airflows and transferring thermal energy from the higher temperature airflow to the lower temperature level can overcome the mentioned shortcomings. In order to demonstrate the feasibility of a friction ventilator to operate as ventilation system with heat recovery computational fluid dynamics were used to analyze the resulting pressure jump and volume flow for different geometrical setups. An extensive grid dependency study for a defined operating point that represents the typical use has been carried out in order to improve the numerical results. Furthermore, the results were compared to experimental data whenever possible.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Advanced Engineering Forum
- Vol. 19, 35-42
Numerical Investigation of a Friction Ventilator for Different Geometrical Setups
Conventional ventilation systems with heat recovery used for building aeration exhibit characteristic disadvantages arising from their operating principle such as noise generation from bladed ventilators or remarkable pressure losses generated by heat exchangers. A novel concept that combines ventilators and heat exchanger in one compact friction ventilator that rotates in two separated ducts producing two opposed airflows and transferring thermal energy from the higher temperature airflow to the lower temperature level can overcome the mentioned shortcomings. In order to demonstrate the feasibility of a friction ventilator to operate as ventilation system with heat recovery computational fluid dynamics were used to analyze the resulting pressure jump and volume flow for different geometrical setups. An extensive grid dependency study for a defined operating point that represents the typical use has been carried out in order to improve the numerical results. Furthermore, the results were compared to experimental data whenever possible.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Advanced Engineering Forum
- Vol. 19, 3-9
Effect of Boundary Layer Tripping on the Aeroacoustics of Small Vertical Axis Wind Turbines
Small wind turbines are investigated as a possible solution for using wind energy at small scales in urban and suburban areas. Most turbines are suffering from a low aerodynamic performance due to turbulent and complex wind situations in cities. Therefore, increasing aerodynamic performance and reducing noise is an important factor to design small wind turbines. In order to optimize such turbines with respect to noise and efficiency it is important to understand the physical mechanisms. Measuring acoustic in urban environment it is hardly possible to obtain reproducible results, which are necessary for a comprehensively and profoundly investigation. Therefore, experimental studies have to been performed in anechoic wind tunnels. Those tunnels are mostly limited in size, which makes it quite difficult to investigate full small wind turbine models. Hence a model scale has to be used in order to measure the power and acoustic performance. For comparing the model scale results with original turbines, the same flow conditions around the airfoils are necessary. Due to the smaller size of the model scale the relative velocities of the blades are less, which can result in a laminar boundary layer. In order to force transition from laminar to turbulent, boundary layer trips can be used. The focus of this study is to examine and quantify the effect of boundary layer tripping on the aeroacoustics in case of small vertical axis wind turbines.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Advanced Engineering Forum
- Vol. 19, 3-9
Effect of Boundary Layer Tripping on the Aeroacoustics of Small Vertical Axis Wind Turbines
Small wind turbines are investigated as a possible solution for using wind energy at small scales in urban and suburban areas. Most turbines are suffering from a low aerodynamic performance due to turbulent and complex wind situations in cities. Therefore, increasing aerodynamic performance and reducing noise is an important factor to design small wind turbines. In order to optimize such turbines with respect to noise and efficiency it is important to understand the physical mechanisms. Measuring acoustic in urban environment it is hardly possible to obtain reproducible results, which are necessary for a comprehensively and profoundly investigation. Therefore, experimental studies have to been performed in anechoic wind tunnels. Those tunnels are mostly limited in size, which makes it quite difficult to investigate full small wind turbine models. Hence a model scale has to be used in order to measure the power and acoustic performance. For comparing the model scale results with original turbines, the same flow conditions around the airfoils are necessary. Due to the smaller size of the model scale the relative velocities of the blades are less, which can result in a laminar boundary layer. In order to force transition from laminar to turbulent, boundary layer trips can be used. The focus of this study is to examine and quantify the effect of boundary layer tripping on the aeroacoustics in case of small vertical axis wind turbines.
- 23 August 2016
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1140, 320-327
Active Wind Turbine Deicing-Systems Produced via Plasma-Coating-Technology
Within the framework of the Renewable Energies Act, besides biomass power stations wind turbine systems enact a significant role since they produce power by using a primary source of renewable energies. As widespread and technical advanced wind turbines are, they still exhibit shortcomings when operating in cold temperatures. Therefore, especially in frigid regions, there is a high risk regarding icing and forming of hoarfrost. Iced rotor blades lead to considerable disadvantages during operation, like ice shedding, unbalanced or off-centered loads, and downtimes.Different heating systems that are already available show some disadvantages, such as the difficulties in integrating the installation of those systems directly in the production process. Thus, a new technology is presented which eliminates existing challenges and can be integrated into current production lines. Furthermore, the results of the investigations for the applicability of this new system for de-icing wind turbines is pictured. Due to an innovative plasma technology, the surfaces of rotor blades can be coated with a heating structure layer. The new technology is presented and the influence of different machine parameters of the coating process are shown based on several experimental results. In further tests, the metal structured rotor blades are examined under real conditions and the suitability of this technology for a series launch is rated.
- 23 August 2016
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1140, 320-327
Active Wind Turbine Deicing-Systems Produced via Plasma-Coating-Technology
Within the framework of the Renewable Energies Act, besides biomass power stations wind turbine systems enact a significant role since they produce power by using a primary source of renewable energies. As widespread and technical advanced wind turbines are, they still exhibit shortcomings when operating in cold temperatures. Therefore, especially in frigid regions, there is a high risk regarding icing and forming of hoarfrost. Iced rotor blades lead to considerable disadvantages during operation, like ice shedding, unbalanced or off-centered loads, and downtimes.Different heating systems that are already available show some disadvantages, such as the difficulties in integrating the installation of those systems directly in the production process. Thus, a new technology is presented which eliminates existing challenges and can be integrated into current production lines. Furthermore, the results of the investigations for the applicability of this new system for de-icing wind turbines is pictured. Due to an innovative plasma technology, the surfaces of rotor blades can be coated with a heating structure layer. The new technology is presented and the influence of different machine parameters of the coating process are shown based on several experimental results. In further tests, the metal structured rotor blades are examined under real conditions and the suitability of this technology for a series launch is rated.