Volkan Arslan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Latest Publications
- 30 April 2022
- Published by Allerton Press in Russian Journal of Non-Ferrous Metals
- Vol. 63 (2) , 146-156
Optimal Factor Evaluation for the Extraction of Alumina from Clays by Sulfuric Acid Leaching Process Using Box–Behnken Design Methodology
Calcination experiments were carried out using calcined clay and optimum calcination conditions were determined as 750°C and 60 min. The Box–Beh
- 30 April 2022
- Published by Allerton Press in Russian Journal of Non-Ferrous Metals
- Vol. 63 (2) , 146-156
Optimal Factor Evaluation for the Extraction of Alumina from Clays by Sulfuric Acid Leaching Process Using Box–Behnken Design Methodology
Calcination experiments were carried out using calcined clay and optimum calcination conditions were determined as 750°C and 60 min. The Box–Beh
- 12 July 2021
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 38 (5) , 2229-2237
The Modeling and Optimization of Iron Removal from Silica Sand Under Ultrasound-Assisted Leaching by Response Surface Methodology
- 12 July 2021
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 38 (5) , 2229-2237
The Modeling and Optimization of Iron Removal from Silica Sand Under Ultrasound-Assisted Leaching by Response Surface Methodology
- 12 July 2021
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 23 (5) , 2005-2015
Bacterial leaching of copper, zinc, nickel and aluminum from discarded printed circuit boards using acidophilic bacteria
- 12 July 2021
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 23 (5) , 2005-2015
Bacterial leaching of copper, zinc, nickel and aluminum from discarded printed circuit boards using acidophilic bacteria
- 14 April 2021
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 57 (3) , 97-111
A study on the dissolution kinetics of iron oxide leaching from clays by oxalic acid
Clay is widely used in a number of industries due to its special properties like fine particle size, brightness and whiteness, chemical inertness, platy structure, etc. In this study, the general characteristics of clays have been investigated by XRF, XRD, FT-IR, TG-DTA and SEM. The presence of...
- 14 April 2021
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 57 (3) , 97-111
A study on the dissolution kinetics of iron oxide leaching from clays by oxalic acid
Clay is widely used in a number of industries due to its special properties like fine particle size, brightness and whiteness, chemical inertness, platy structure, etc. In this study, the general characteristics of clays have been investigated by XRF, XRD, FT-IR, TG-DTA and SEM. The presence of...
- 31 December 2020
- Published by Mugla Sitki Kocman University in Mugla Journal of Science and Technology
- Vol. 6 (2) , 43-51
A FUZZY APPLICATION OF X-R CONTROL CHARTS OF AN ALUMINUM PRODUCTION PLANT USING FUZZY TRIANGULAR NUMBERS
In this study, fuzzy mean and range control charts were used to follow the feeding material and concentrate production line of Eti Aluminum Co. Fuzzy control charts were collected from the factory over a period of time and compared to Shewhart control charts used by the factory. The results showed that fuzzy control charts detected errors in the production process more accurately than Shewhart control charts. This method has increased quality and efficiency. Process capability indices (PCIs) provide numerical measures as to whether a process has confirmed the defined capability prerequisite. These were used to measure the process's ability to decide how well it meets specification limits (SLs). PCIs have been implemented by companies to evaluate quality and efficiency performance. Fuzzy process capability analysis using X-R control charts gave more accurate results.
- 31 December 2020
- Published by Mugla Sitki Kocman University in Mugla Journal of Science and Technology
- Vol. 6 (2) , 43-51
A FUZZY APPLICATION OF X-R CONTROL CHARTS OF AN ALUMINUM PRODUCTION PLANT USING FUZZY TRIANGULAR NUMBERS
In this study, fuzzy mean and range control charts were used to follow the feeding material and concentrate production line of Eti Aluminum Co. Fuzzy control charts were collected from the factory over a period of time and compared to Shewhart control charts used by the factory. The results showed that fuzzy control charts detected errors in the production process more accurately than Shewhart control charts. This method has increased quality and efficiency. Process capability indices (PCIs) provide numerical measures as to whether a process has confirmed the defined capability prerequisite. These were used to measure the process's ability to decide how well it meets specification limits (SLs). PCIs have been implemented by companies to evaluate quality and efficiency performance. Fuzzy process capability analysis using X-R control charts gave more accurate results.
- 14 September 2020
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 42 (7) , 2114-2126
The application of combined lignite cleaning processes, bacterial leaching and flotation, for reducing higher ash and sulfur contents
In this study, biological and physicochemical processes were combined to decrease the ash and sulfur contents of finely ground coal. Firstly, biodesulphurization experiments of lignites with high ash and sulfur contents were carried out with air-supply fiberglass bioreactor using Acidithiobacillus ferrooxidans. At the end of the 12-hour bacterial desulfurization experiments; ash content, sulfur content, calorific value, sulfur emission value, recovery of calorific value, and combustible recovery values were 33.88%, 3.97%, 3982 kcal/kg, 0.24% 91.22%, and 89.74%, respectively. Afterward, in the second stage experiments, flotation method was used to beneficiation Can/Canakkale lignites by physicochemical methods. In flotation experiments, the effects of collector (Fuel oil; 0–900 g/t) and frother (MIBC; 0–300 g/t) dosages on flotation were investigated. Optimum collector and frother dosages were determined as 750 g/t and 250 g/t in flotation experiments, respectively. In flotation experiments under optimum conditions ash content, sulfur content, calorific value, sulfur emission value, recovery of calorific value and combustible recovery values were 16.38%, 0.75%, 5166 kcal/kg, 0.03% 98.60%, and 96.11%, respectively. As a result of all experiments, ash and sulfur removal efficiencies were carried out 65.12% and 86.93% in Can/Canakkale lignites, respectively.
- 14 September 2020
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 42 (7) , 2114-2126
The application of combined lignite cleaning processes, bacterial leaching and flotation, for reducing higher ash and sulfur contents
In this study, biological and physicochemical processes were combined to decrease the ash and sulfur contents of finely ground coal. Firstly, biodesulphurization experiments of lignites with high ash and sulfur contents were carried out with air-supply fiberglass bioreactor using Acidithiobacillus ferrooxidans. At the end of the 12-hour bacterial desulfurization experiments; ash content, sulfur content, calorific value, sulfur emission value, recovery of calorific value, and combustible recovery values were 33.88%, 3.97%, 3982 kcal/kg, 0.24% 91.22%, and 89.74%, respectively. Afterward, in the second stage experiments, flotation method was used to beneficiation Can/Canakkale lignites by physicochemical methods. In flotation experiments, the effects of collector (Fuel oil; 0–900 g/t) and frother (MIBC; 0–300 g/t) dosages on flotation were investigated. Optimum collector and frother dosages were determined as 750 g/t and 250 g/t in flotation experiments, respectively. In flotation experiments under optimum conditions ash content, sulfur content, calorific value, sulfur emission value, recovery of calorific value and combustible recovery values were 16.38%, 0.75%, 5166 kcal/kg, 0.03% 98.60%, and 96.11%, respectively. As a result of all experiments, ash and sulfur removal efficiencies were carried out 65.12% and 86.93% in Can/Canakkale lignites, respectively.
- Open Access
- 1 September 2019
- Published by Bilimsel Madencilik Dergisi in Bilimsel Madencilik Dergisi
- Vol. 58 (3) , 219-228
TOPLAM RENK FARKLILIĞI PARAMETRESİ KULLANILARAK BULANIK MANTIK YÖNTEMİYLE İSTATİSTİKSEL KALİTE KONTROLÜ: ALÜMİNYUM ÜRETİM TESİSİNDE BİR UYGULAMA
Üretim sürecini izlemek için bulanık bir ortalama ve değişim aralığı kontrol çizelgeleri kullanılmıştır.Bulanık kontrol grafikleri, fabrikadan veri toplayarak ve bunu prosesin izlenmesi için fabrikatarafından zaten uygulanmış olan geleneksel Shewhart kontrol grafikleri ile karşılaştırarak,alüminyum üretim tesisindeki bir vaka çalışması ile doğrulanmıştır. Sonuçlar, önerilen bulanıkkontrol grafiklerinin, üretim sürecindeki anormal değişimleri, geleneksel Shewhart kontrollistelerinden daha doğru bir şekilde tespit edebildiğini, çünkü süreçten daha fazla bilgikullandıklarını ortaya koymaktadır.Bu çalışmada, Eti Alüminyum A.Ş. alüminyum üretim tesisinde bulanık mantık istatistiksel kalitekontrol uygulaması yapılmıştır. Toplam renk farkı parametresi (ΔE) verileri, alüminyum üretimtesisinde bulanık gözlem yöntemi kullanılarak incelenmiştir. Bu amaçla, alüminyum üretim tesisiürünlerinin renk parametreleri, ilgili formüller yardımıyla hesaplanan bulanık üçgen sayılar (TFN)ve bulanık süreç yeterlilik indeksleri (PCI) kullanılarak değerlendirilmiştir. Elde edilen bilgilerleüretim sürecinin yeterli olup olmadığını tespit etmek amacıyla proses yeterlilik analizi yapılmıştır.Cp, Cpu ve Cpl indisleri sırası ile 1,267, 1,263, 1,257; 1,419, 1,414, 1,408 ve 1,115, 1,111, 1,106bulunmuştur. Bu değerlere göre prosesin ihtiyaçları karşıladığı tespit edilmiştir.
- 1 September 2019
- Published by Bilimsel Madencilik Dergisi in Bilimsel Madencilik Dergisi
- Vol. 58 (3) , 219-228
Open AccessTOPLAM RENK FARKLILIĞI PARAMETRESİ KULLANILARAK BULANIK MANTIK YÖNTEMİYLE İSTATİSTİKSEL KALİTE KONTROLÜ: ALÜMİNYUM ÜRETİM TESİSİNDE BİR UYGULAMA
Üretim sürecini izlemek için bulanık bir ortalama ve değişim aralığı kontrol çizelgeleri kullanılmıştır.Bulanık kontrol grafikleri, fabrikadan veri toplayarak ve bunu prosesin izlenmesi için fabrikatarafından zaten uygulanmış olan geleneksel Shewhart kontrol grafikleri ile karşılaştırarak,alüminyum üretim tesisindeki bir vaka çalışması ile doğrulanmıştır. Sonuçlar, önerilen bulanıkkontrol grafiklerinin, üretim sürecindeki anormal değişimleri, geleneksel Shewhart kontrollistelerinden daha doğru bir şekilde tespit edebildiğini, çünkü süreçten daha fazla bilgikullandıklarını ortaya koymaktadır.Bu çalışmada, Eti Alüminyum A.Ş. alüminyum üretim tesisinde bulanık mantık istatistiksel kalitekontrol uygulaması yapılmıştır. Toplam renk farkı parametresi (ΔE) verileri, alüminyum üretimtesisinde bulanık gözlem yöntemi kullanılarak incelenmiştir. Bu amaçla, alüminyum üretim tesisiürünlerinin renk parametreleri, ilgili formüller yardımıyla hesaplanan bulanık üçgen sayılar (TFN)ve bulanık süreç yeterlilik indeksleri (PCI) kullanılarak değerlendirilmiştir. Elde edilen bilgilerleüretim sürecinin yeterli olup olmadığını tespit etmek amacıyla proses yeterlilik analizi yapılmıştır.Cp, Cpu ve Cpl indisleri sırası ile 1,267, 1,263, 1,257; 1,419, 1,414, 1,408 ve 1,115, 1,111, 1,106bulunmuştur. Bu değerlere göre prosesin ihtiyaçları karşıladığı tespit edilmiştir.
- 2 May 2019
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 189 (2) , 437-447
Comparison of the Effects of Aspergillus niger and Aspergillus ficuum on the Removal of Impurities in Feldspar by Bio-beneficiation
Depending on its purity, feldspar has a wide application in industry. Fungi play an important role in the feldspar purification. A bacterial leaching study of feldspar sample from Aydin, Turkey, was conducted to obtain a suitable raw material for industrial applications. XRD analyses indicated that albite (NaAlSi3O8) with minor amounts of orthoclase (KAlSi3O8), quartz (SiO2), muscovite (KAl2(Si3AlO10)(OH)2), rutile (TiO2), and small quantities of weathered clay minerals. This study evaluates bacterial leaching treatment to iron removal from feldspar using Aspergillus niger and Aspergillus ficuum to attain a product suitable for industrial uses. These funguses were tested for organic acid (oxalic and citric acid) production and leaching capabilities of feldspar. The leaching performances of two funguses were compared. Bacterial leaching experiments were performed in 500-mL Erlenmeyer flask at 30 ± 2 °C and 180 rpm agitation under aseptic conditions. In bacterial leaching experiments using A. niger and A. ficuum, 70.13% and 85.09% of the total iron oxides in the feldspar were removed, respectively. As a result, the final iron oxide concentrations in bacterial leaching experiments using A. niger and A. ficuum were 0.095% and 0.047%, respectively (at 5% w/v pulp density, temperature 30 ± 2 °C, A. niger 3 × 107 spores, A. ficuum 5 × 107 spores, and particle size < 63 μm). The use of fungi to remove iron from feldspar has the potential to be an effective method for upgrading the content and the commercial value of the feldspar. The experimental results of this study have provided significant opportunity to use biotechnological approach for producing the feldspar as a feed material for the high-quality ceramic industry.
- 2 May 2019
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 189 (2) , 437-447
Comparison of the Effects of Aspergillus niger and Aspergillus ficuum on the Removal of Impurities in Feldspar by Bio-beneficiation
Depending on its purity, feldspar has a wide application in industry. Fungi play an important role in the feldspar purification. A bacterial leaching study of feldspar sample from Aydin, Turkey, was conducted to obtain a suitable raw material for industrial applications. XRD analyses indicated that albite (NaAlSi3O8) with minor amounts of orthoclase (KAlSi3O8), quartz (SiO2), muscovite (KAl2(Si3AlO10)(OH)2), rutile (TiO2), and small quantities of weathered clay minerals. This study evaluates bacterial leaching treatment to iron removal from feldspar using Aspergillus niger and Aspergillus ficuum to attain a product suitable for industrial uses. These funguses were tested for organic acid (oxalic and citric acid) production and leaching capabilities of feldspar. The leaching performances of two funguses were compared. Bacterial leaching experiments were performed in 500-mL Erlenmeyer flask at 30 ± 2 °C and 180 rpm agitation under aseptic conditions. In bacterial leaching experiments using A. niger and A. ficuum, 70.13% and 85.09% of the total iron oxides in the feldspar were removed, respectively. As a result, the final iron oxide concentrations in bacterial leaching experiments using A. niger and A. ficuum were 0.095% and 0.047%, respectively (at 5% w/v pulp density, temperature 30 ± 2 °C, A. niger 3 × 107 spores, A. ficuum 5 × 107 spores, and particle size < 63 μm). The use of fungi to remove iron from feldspar has the potential to be an effective method for upgrading the content and the commercial value of the feldspar. The experimental results of this study have provided significant opportunity to use biotechnological approach for producing the feldspar as a feed material for the high-quality ceramic industry.
- Open Access
- 15 March 2017
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 32 (1) , 99-108
Bakır Konsantre Tesislerinde Kontrol Kartlarının ve Çok Boyutlu Ölçekleme Analizinin Uygulanması
Tr en Bu çalışmada, Türkiye’deki iki bakır zenginleştirme tesisinde istatistiksel kalite kontrol uygulaması yapılmıştır. Elde edilen bilgilerle üretim sürecinin yeterli olup olmadığını tespit etmek amacıyla proses yeterlilik analizi yapılmıştır. A ve B tesisleri için Cp ve Cpk indisleri sırası ile 1,42, 1,20 ve 1,50, 1,10 bulunmuştur. Bu değerlere göre proseslerin ihtiyaçları karşıladığı tespit edilmiştir. Ayrıca, çok boyutlu ölçekleme (ÇBÖ) analizi ile stress değeri ve korelasyon indeksi değeri tespit edilmiştir. Hesaplamalar sonucunda stress değeri 0,01258 bulunmuş ve bu değer konfigürasyon uzaklıkları ile tahmini uzaklıklar arasında mükemmel bir uyum olduğunu göstermiştir. Korelasyon indeksi değeri (R2) 0,99923’dür. Bu değer güvenilirlik açısından öklid uzaklık modelinin verileri çok iyi temsil ettiğini göstermektedir. Çok boyutlu ölçekleme analizi sonuçlarının çalışmada kullanılan veri setini yeterli ölçüde yansıttığı görülmektedir. In this study, statistical quality control application was applied to two copper concentrate plants in Turkey. Process capability analysis was carried out to determine whether there was sufficient of the production process with the information obtained. The Cp and Cpk indices for A and B plants were 1.42, 1.20 and 1.50, 1.10, respectively. According to these values, it has been determined that the processes meet the needs. Furthermore, stress index value and the correlation value were determined with multidimensional scaling (MDS) analysis. As a result of the calculations, the stress value was founded 0.01258, indicating that this was a perfect fit between the configuration distances and the estimated distances. The correlation index value (R2) was 0.99923. This value showed that the euclidean distance model represents the data very well in terms of reliability. Multidimensional scaling analysis of the results of the data set used in this study seems to adequately reflect.
- 15 March 2017
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 32 (1) , 99-108
Open AccessBakır Konsantre Tesislerinde Kontrol Kartlarının ve Çok Boyutlu Ölçekleme Analizinin Uygulanması
Tr en Bu çalışmada, Türkiye’deki iki bakır zenginleştirme tesisinde istatistiksel kalite kontrol uygulaması yapılmıştır. Elde edilen bilgilerle üretim sürecinin yeterli olup olmadığını tespit etmek amacıyla proses yeterlilik analizi yapılmıştır. A ve B tesisleri için Cp ve Cpk indisleri sırası ile 1,42, 1,20 ve 1,50, 1,10 bulunmuştur. Bu değerlere göre proseslerin ihtiyaçları karşıladığı tespit edilmiştir. Ayrıca, çok boyutlu ölçekleme (ÇBÖ) analizi ile stress değeri ve korelasyon indeksi değeri tespit edilmiştir. Hesaplamalar sonucunda stress değeri 0,01258 bulunmuş ve bu değer konfigürasyon uzaklıkları ile tahmini uzaklıklar arasında mükemmel bir uyum olduğunu göstermiştir. Korelasyon indeksi değeri (R2) 0,99923’dür. Bu değer güvenilirlik açısından öklid uzaklık modelinin verileri çok iyi temsil ettiğini göstermektedir. Çok boyutlu ölçekleme analizi sonuçlarının çalışmada kullanılan veri setini yeterli ölçüde yansıttığı görülmektedir. In this study, statistical quality control application was applied to two copper concentrate plants in Turkey. Process capability analysis was carried out to determine whether there was sufficient of the production process with the information obtained. The Cp and Cpk indices for A and B plants were 1.42, 1.20 and 1.50, 1.10, respectively. According to these values, it has been determined that the processes meet the needs. Furthermore, stress index value and the correlation value were determined with multidimensional scaling (MDS) analysis. As a result of the calculations, the stress value was founded 0.01258, indicating that this was a perfect fit between the configuration distances and the estimated distances. The correlation index value (R2) was 0.99923. This value showed that the euclidean distance model represents the data very well in terms of reliability. Multidimensional scaling analysis of the results of the data set used in this study seems to adequately reflect.