Nagarajan Parasumanna Krishnamurthy
Research Subjects
Nagarajan Parasumanna Krishnamurthy has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Ravishankar Sathyamurthy
Department of Mechanical Engineering, King Fahd University of Petroleum & Minerals, Dhahran 31261, Saudi Arabia
23 shared publications - Devarajan Mageshbabu
Department of Mechatronics Engineering Velammal Institute of Technology Panjetty Tamil Nadu India
5 shared publications - Amimul Ahsan
Department of Civil and Environmental Engineering, Islamic University of Technology (IUT), Gazipur 1704, Bangladesh
4 shared publications - Balasubramanian Madhu
Velammal Institute of Technology
4 shared publications J. Subramani
Department of Mechanical Engineering, S.A. Engineering College Affiliated to Anna University Chennai Tamil Nadu India
4 shared publicationsS.A. El-Agouz
4 shared publications
Latest Publications
- 19 September 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (10) , 105943
Studying the STA effects on aluminium alloy joints by friction welding
This article examines the properties of joints fabricated by friction welding (FW) using AA6061-T6 and AA7075 as examples of both similar and dissimilar metals. It also looks at how heat treatment after welding affects the metallurgical characteristics of the joint. The heat treatment method under investigation combines solutionizing heat treatment with synthetic ageing (STA). The tensile characteristics, microhardness, and microstructure of the as-welded and STA-treated welded specimens are assessed in the paper using mechanical testing equipment and metallurgical characterization methods. The findings demonstrate that the joint characteristics are enhanced by precipitate nucleation occurring in the joint interface of the FW similar and dissimilar joint under STA treatment. On the other hand, the STA influence on the tensile strength (TS) of joints made with AA7075 was greater than that of similar joints made with AA6061-T6, as well as dissimilar joints made with both AA6061-T6 and AA7075. Additionally, after STA treatment, the similar joints showed a uniform distribution of hardness. However, in the dissimilar joint after STA treatment, the hardness dropped suddenly on the AA6061-T6 side, specifically from the partially deformed zone (PDZ) towards the heat affected zone (HAZ).
- 19 September 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (10) , 105943
Studying the STA effects on aluminium alloy joints by friction welding
This article examines the properties of joints fabricated by friction welding (FW) using AA6061-T6 and AA7075 as examples of both similar and dissimilar metals. It also looks at how heat treatment after welding affects the metallurgical characteristics of the joint. The heat treatment method under investigation combines solutionizing heat treatment with synthetic ageing (STA). The tensile characteristics, microhardness, and microstructure of the as-welded and STA-treated welded specimens are assessed in the paper using mechanical testing equipment and metallurgical characterization methods. The findings demonstrate that the joint characteristics are enhanced by precipitate nucleation occurring in the joint interface of the FW similar and dissimilar joint under STA treatment. On the other hand, the STA influence on the tensile strength (TS) of joints made with AA7075 was greater than that of similar joints made with AA6061-T6, as well as dissimilar joints made with both AA6061-T6 and AA7075. Additionally, after STA treatment, the similar joints showed a uniform distribution of hardness. However, in the dissimilar joint after STA treatment, the hardness dropped suddenly on the AA6061-T6 side, specifically from the partially deformed zone (PDZ) towards the heat affected zone (HAZ).
- Open Access
- 1 September 2018
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 57 (3) , 1205-1215
Formation, characterization and theoretical evaluation of combustion of biodiesel obtained from wax esters of A. Mellifera
- 1 September 2018
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 57 (3) , 1205-1215
Open AccessFormation, characterization and theoretical evaluation of combustion of biodiesel obtained from wax esters of A. Mellifera
- 4 May 2018
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 38 (1) , 286-296
Different parameters affecting the condensation rate on an active solar still—A review
Passive solar stills are used for solar distillation. But the yield of passive still is very low, and often fails to meet the demand. Water is one of the fundamental sources for the survival of mankind on the globe. As world having just a little measure of water assets for utilization purpose, individuals living in undeveloped countries and urban zones are getting affected by consuming dirty water that prompts water‐borne illness. Despite the fact that groundwater is accessible in little amount, it must be suitably treated before its utilization for domestic use. Salty water contains dissolved and undissolved substance, and henceforth, it is not advisable for family drinking purpose. To enhance the productivity of fresh water, several techniques were employed. Furthermore, increase in yield of fresh water depends on various environmental parameters and rate of condensation. In this article, a complete review of various methods employed to enhance the condensation rate on an active solar still has been presented. Solar still incorporated with the evacuated tube collectors (ETC) and thermo electric modules (TEM) increased the still effectiveness up to 68%. © 2018 American Institute of Chemical Engineers Environ Prog, 38: 286–296, 2019
- 4 May 2018
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 38 (1) , 286-296
Different parameters affecting the condensation rate on an active solar still—A review
Passive solar stills are used for solar distillation. But the yield of passive still is very low, and often fails to meet the demand. Water is one of the fundamental sources for the survival of mankind on the globe. As world having just a little measure of water assets for utilization purpose, individuals living in undeveloped countries and urban zones are getting affected by consuming dirty water that prompts water‐borne illness. Despite the fact that groundwater is accessible in little amount, it must be suitably treated before its utilization for domestic use. Salty water contains dissolved and undissolved substance, and henceforth, it is not advisable for family drinking purpose. To enhance the productivity of fresh water, several techniques were employed. Furthermore, increase in yield of fresh water depends on various environmental parameters and rate of condensation. In this article, a complete review of various methods employed to enhance the condensation rate on an active solar still has been presented. Solar still incorporated with the evacuated tube collectors (ETC) and thermo electric modules (TEM) increased the still effectiveness up to 68%. © 2018 American Institute of Chemical Engineers Environ Prog, 38: 286–296, 2019
- Open Access
- 1 March 2018
- Published by Institution of Engineering and Technology (IET) in Micro & Nano Letters
- Vol. 13 (3) , 335-340
Synthesis, characterisation and thermo‐physical investigations on magnesia nanoparticles dispersed in ethylene glycol–DI water (50:50)
In the present work, magnesia nanoparticles (17 nm) were synthesised by solution combustion and characterised using X‐ray diffraction and scanning electron microscopy. Nanofluid prepared by magnesia dispersion in ethylene glycol and deionised water (50:50) is characterised using Fourier transform infrared, dynamic light scattering (DLS) and Zeta potential measurement. The ‐41 mV zeta potential confirms nanofluid stability. The average particle size in the nanofluid obtained by the DLS method is 33 nm, whereas the crystallite size is 17 nm as per the Scherrer relation. The nanofluid properties were determined under varying volume concentration (0.025, 0.05, 0.1, 0.2%) and temperature (25–60°C). The viscosity measured by using a rotational viscometer decreases with increase in the temperature, whereas the thermal conductivity and specific heat, measured by using a KD2 Pro analyser and a differential scanning calorimeter, respectively, increases. With the increase in volume concentration, thermal conductivity, and viscosity increases, whereas specific heat decreases. The maximum thermal conductivity enhancement and specific heat diminution was 15.6 and 20.5%, respectively, for 0.2% concentration and the minimum viscosity was 2.2% for 0.025% concentration at 60°C. Based on the measured data, new correlations have been proposed.
- 1 March 2018
- Published by Institution of Engineering and Technology (IET) in Micro & Nano Letters
- Vol. 13 (3) , 335-340
Open AccessSynthesis, characterisation and thermo‐physical investigations on magnesia nanoparticles dispersed in ethylene glycol–DI water (50:50)
In the present work, magnesia nanoparticles (17 nm) were synthesised by solution combustion and characterised using X‐ray diffraction and scanning electron microscopy. Nanofluid prepared by magnesia dispersion in ethylene glycol and deionised water (50:50) is characterised using Fourier transform infrared, dynamic light scattering (DLS) and Zeta potential measurement. The ‐41 mV zeta potential confirms nanofluid stability. The average particle size in the nanofluid obtained by the DLS method is 33 nm, whereas the crystallite size is 17 nm as per the Scherrer relation. The nanofluid properties were determined under varying volume concentration (0.025, 0.05, 0.1, 0.2%) and temperature (25–60°C). The viscosity measured by using a rotational viscometer decreases with increase in the temperature, whereas the thermal conductivity and specific heat, measured by using a KD2 Pro analyser and a differential scanning calorimeter, respectively, increases. With the increase in volume concentration, thermal conductivity, and viscosity increases, whereas specific heat decreases. The maximum thermal conductivity enhancement and specific heat diminution was 15.6 and 20.5%, respectively, for 0.2% concentration and the minimum viscosity was 2.2% for 0.025% concentration at 60°C. Based on the measured data, new correlations have been proposed.
- 3 October 2017
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 37 (3) , 1149-1159
Experimental study on the thermal performance and heat transfer characteristics of solar parabolic trough collector using Al2O3 nanofluids
The present work investigated thermal performance and heat transfer characteristics of a solar parabolic trough collector using Al2O3/DI‐H2O nanofluids. Nanofluids of varying concentrations (0.05% ϕ ≤ 0.5%) with mass flows (0.0083–0.05 kg/s) were considered for turbulent regime (2401 ≤ Re ≤ 7202) analysis. Experiments were carried out as per ASHRAE 93(2010) standards. By thermal performance analysis using Al2O3 nanofluid, it was understood that the collector efficiency improved up to 56% at a maximum volume concentration of ϕ = 0.5% and flow rate of 0.05 kg/s. The heat transfer study comparing Al2O3 nanofluid with pure water showed appreciable reduction in temperature gradient and surface temperature of the absorber. The heat transfer characteristics such as Nusselt number and friction factor relating to Reynolds number fits the experimental and predicted data and found within the limits of ±5.35% and ±9.61% for Nusselt number and friction factor respectively. Moreover, a similar empirical correlation was developed for collector efficiency, which was identified to be within the limit of ±1.02%. © 2017 American Institute of Chemical Engineers Environ Prog, 37: 1149–1159, 2018
- 3 October 2017
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 37 (3) , 1149-1159
Experimental study on the thermal performance and heat transfer characteristics of solar parabolic trough collector using Al2O3 nanofluids
The present work investigated thermal performance and heat transfer characteristics of a solar parabolic trough collector using Al2O3/DI‐H2O nanofluids. Nanofluids of varying concentrations (0.05% ϕ ≤ 0.5%) with mass flows (0.0083–0.05 kg/s) were considered for turbulent regime (2401 ≤ Re ≤ 7202) analysis. Experiments were carried out as per ASHRAE 93(2010) standards. By thermal performance analysis using Al2O3 nanofluid, it was understood that the collector efficiency improved up to 56% at a maximum volume concentration of ϕ = 0.5% and flow rate of 0.05 kg/s. The heat transfer study comparing Al2O3 nanofluid with pure water showed appreciable reduction in temperature gradient and surface temperature of the absorber. The heat transfer characteristics such as Nusselt number and friction factor relating to Reynolds number fits the experimental and predicted data and found within the limits of ±5.35% and ±9.61% for Nusselt number and friction factor respectively. Moreover, a similar empirical correlation was developed for collector efficiency, which was identified to be within the limit of ±1.02%. © 2017 American Institute of Chemical Engineers Environ Prog, 37: 1149–1159, 2018
- Top Cited Papers
- 1 September 2017
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 77, 1069-1097
A Review of integrating solar collectors to solar still
- 1 September 2017
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 77, 1069-1097
Top Cited PapersA Review of integrating solar collectors to solar still
- 1 March 2017
- Published by Natural Sciences Publishing in Applied Mathematics & Information Sciences
- Vol. 11 (2) , 545-555
Investigation of High Temperature Cyclic Pressurization of Titanium Ducts
- 1 March 2017
- Published by Natural Sciences Publishing in Applied Mathematics & Information Sciences
- Vol. 11 (2) , 545-555
Investigation of High Temperature Cyclic Pressurization of Titanium Ducts
- Open Access
- 1 March 2017
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 56 (1) , 43-54
Influence of aspect ratio on the thermal performance of rectangular shaped micro channel heat sink using CFD code
- 1 March 2017
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 56 (1) , 43-54
Open AccessInfluence of aspect ratio on the thermal performance of rectangular shaped micro channel heat sink using CFD code
- 24 January 2017
- Published by Taylor & Francis in Experimental Heat Transfer
- Vol. 30 (4) , 267-283
Enhancing the thermal performance of AL2O3/DI water nanofluids in micro-fin tube equipped with straight and left-right twisted tapes in turbulent flow regime
This article communicates the thermal performance, heat transfer rate, and friction factor of Al2O3/DI water nanofluids at different concentrations in a micro-finned tube with tube helical inserts for different twist ratios. The thermal performance, heat transfer coefficient, and friction of the present study is also compared with a plain tube for validation. From the study, it is identified that the micro-finned tube with tube insert performance is higher as compared with a plain tube. Similarly, an empirical relation for Nusselt number (Nu) and friction factor (f) is estimated for straight twisted tube and left-right combination. The deviation between experimental and theoretical values for left-right twist and straight twist is found as 3 and 7% for Nusselt number and 7 and 9% for friction factor, respectively. Similarly, while analyzing the thermal performance, it was found that the maximum performance achieved was with a micro-fin tube with left-right twist with nanofluid concentration of 0.2%.
- 24 January 2017
- Published by Taylor & Francis in Experimental Heat Transfer
- Vol. 30 (4) , 267-283
Enhancing the thermal performance of AL2O3/DI water nanofluids in micro-fin tube equipped with straight and left-right twisted tapes in turbulent flow regime
This article communicates the thermal performance, heat transfer rate, and friction factor of Al2O3/DI water nanofluids at different concentrations in a micro-finned tube with tube helical inserts for different twist ratios. The thermal performance, heat transfer coefficient, and friction of the present study is also compared with a plain tube for validation. From the study, it is identified that the micro-finned tube with tube insert performance is higher as compared with a plain tube. Similarly, an empirical relation for Nusselt number (Nu) and friction factor (f) is estimated for straight twisted tube and left-right combination. The deviation between experimental and theoretical values for left-right twist and straight twist is found as 3 and 7% for Nusselt number and 7 and 9% for friction factor, respectively. Similarly, while analyzing the thermal performance, it was found that the maximum performance achieved was with a micro-fin tube with left-right twist with nanofluid concentration of 0.2%.