N. I. Taluts
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
N. I. Taluts has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Arkadiy V. Dobromyslov
Mikheev Institute of Metal Physics, Ural Branch, Russian Academy of Sciences, Ekaterinburg 620108, Russia
40 shared publications E. A. Kozlov
Zababakhin All-Russia Research Institute of Technical Physics
18 shared publicationsEvgeniy Kozlov
Russian Federal Nuclear Center – Academician E.I. Zababakhin All-Russian Research Institute of Technical Physics , Snezhinsk , Chelyabinsk Region , Russia
4 shared publicationsA. V. Dobromyslov
M.N. Mikheev Institute of Metal Physics, Ural Branch, Russian Academy of Sciences, Ekaterinburg, Russia
3 shared publicationsA. V. Petrovtsev
Zababakhin All-Russia Research Institute of Technical Physics
3 shared publications- Aleksei N. Uksusnikov
Russian Academy of Sciences
3 shared publications
Latest Publications
- 8 July 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (9) , 3961-3971
Regularities of Orthorhombic α″ Phase Formation in Binary Zirconium Alloys
- 8 July 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (9) , 3961-3971
Regularities of Orthorhombic α″ Phase Formation in Binary Zirconium Alloys
- Open Access
- 1 August 2021
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 122 (8) , 794-799
Shock-Wave Properties and Deformation-Induced Structure of Commercial-Purity Titanium
The shock compressive wave profiles of commercial-purity titanium samples under different loading conditions have been measured. The spall strength of titanium as a function of the strain rate and temperature of deformation has been found. High-rate plastic deformation mechanisms have been studied. High-rate plastic deformation under the investigated loading conditions has been shown to occur by slip and twinning. The α → ω transformation has been established to begin at 12.2 GPa.
- 1 August 2021
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 122 (8) , 794-799
Open AccessShock-Wave Properties and Deformation-Induced Structure of Commercial-Purity Titanium
The shock compressive wave profiles of commercial-purity titanium samples under different loading conditions have been measured. The spall strength of titanium as a function of the strain rate and temperature of deformation has been found. High-rate plastic deformation mechanisms have been studied. High-rate plastic deformation under the investigated loading conditions has been shown to occur by slip and twinning. The α → ω transformation has been established to begin at 12.2 GPa.
- 1 December 2020
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 93, 105354
Severe plastic deformation by high-pressure torsion of Hf and Hf Ti alloys
- 1 December 2020
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 93, 105354
Severe plastic deformation by high-pressure torsion of Hf and Hf Ti alloys
- 1 October 2019
- Published by Elsevier in Materials Characterization
- Vol. 156, 109848
Synthesis of Zr-Zn alloys from elemental powders by severe plastic deformation under pressure
- 1 October 2019
- Published by Elsevier in Materials Characterization
- Vol. 156, 109848
Synthesis of Zr-Zn alloys from elemental powders by severe plastic deformation under pressure
- 30 November 2018
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 119 (11) , 1127-1132
Mechanical Alloying of Ti–Fe Alloys Using Severe Plastic Deformation by High-Pressure Torsion
Alloys of the Ti–Fe system with an iron content from 5 to 90 wt % were synthesized from elemental powders using mechanical alloying in Bridgman anvils. The phase composition and structure of the...
- 30 November 2018
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 119 (11) , 1127-1132
Mechanical Alloying of Ti–Fe Alloys Using Severe Plastic Deformation by High-Pressure Torsion
Alloys of the Ti–Fe system with an iron content from 5 to 90 wt % were synthesized from elemental powders using mechanical alloying in Bridgman anvils. The phase composition and structure of the...
- 23 October 2018
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 119 (10) , 1022-1030
Deformation Behavior of a Copper Single Crystal upon Loading by Spherically Converging Shock Waves
X-ray diffraction analysis, optical metallography examination, and microhardness measurements were used to investigate a copper single crystal sphere 34 mm in diameter after loading by...
- 23 October 2018
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 119 (10) , 1022-1030
Deformation Behavior of a Copper Single Crystal upon Loading by Spherically Converging Shock Waves
X-ray diffraction analysis, optical metallography examination, and microhardness measurements were used to investigate a copper single crystal sphere 34 mm in diameter after loading by...
- 1 March 2018
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 119 (3) , 272-281
Structure of Quenched Ti–Ru Alloys
Quenched titanium–ruthenium alloys containing 0.25–4 at % ruthenium have been studied using X-ray diffraction analysis, optical metallography, transmission electron microscopy, and microhardness...
- 1 March 2018
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 119 (3) , 272-281
Structure of Quenched Ti–Ru Alloys
Quenched titanium–ruthenium alloys containing 0.25–4 at % ruthenium have been studied using X-ray diffraction analysis, optical metallography, transmission electron microscopy, and microhardness...
- 1 June 2017
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 118 (6) , 564-571
Structure of Al–Fe alloys prepared by different methods after severe plastic deformation under pressure
Al–Fe alloys prepared by casting, rapid quenching from the melt, and mechanical alloying from elemental powders have been studied using X-ray diffraction analysis, optical metallography, transmission electron microscopy, and microhardness measurements in the initial state and after severe plastic deformation by high-pressure torsion using Bridgman anvils. The relationship between the phase composition, microstructure, and the microhardness of the investigated alloys has been established.
- 1 June 2017
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 118 (6) , 564-571
Structure of Al–Fe alloys prepared by different methods after severe plastic deformation under pressure
Al–Fe alloys prepared by casting, rapid quenching from the melt, and mechanical alloying from elemental powders have been studied using X-ray diffraction analysis, optical metallography, transmission electron microscopy, and microhardness measurements in the initial state and after severe plastic deformation by high-pressure torsion using Bridgman anvils. The relationship between the phase composition, microstructure, and the microhardness of the investigated alloys has been established.
- 23 July 2016
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 117 (7) , 693-700
Structure of quenched alloys of the Ti–Pd system
- 23 July 2016
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 117 (7) , 693-700
Structure of quenched alloys of the Ti–Pd system
- 16 September 2015
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 116 (9) , 942-950
Mechanical alloying of Al–Fe alloys using severe deformation by high-pressure torsion
Al–Fe alloys with concentrations of iron of up to 50 at % have been produced from elemental powders using severe plastic deformation by high-pressure torsion. The synthesized alloys were studied...
- 16 September 2015
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 116 (9) , 942-950
Mechanical alloying of Al–Fe alloys using severe deformation by high-pressure torsion
Al–Fe alloys with concentrations of iron of up to 50 at % have been produced from elemental powders using severe plastic deformation by high-pressure torsion. The synthesized alloys were studied...