Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ahmed Bakry has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Acid functionalized polypropylene derivatives to adsorb Mn (II) from aqueous solutions: equilibrium, kinetics, and thermodynamic modeling

    by Ahmed Bakry, Salwa M. Elmesallamy, Mohamed Fekry

    Polypropylene wastes were used to prepare carboxylated (CPP) and sulfonated (SPP) microparticles for the adsorption of Mn (II) from aqueous media. The microparticles derivatized with nitric or sulfuric acid were characterized in terms of their physico-chemical properties. The generated functional groups on CPP (–COOH and –NO2) and SPP (–COOH, –SO3H, and C = C) enhanced the adsorption of metal ions. The adsorption behavior of Mn (II) ions on the derivatized microparticles was studied under different conditions: Solution pH, polymer dose, contact time, initial concentration of Mn (II) ions, and temperature. Application of kinetics and equilibrium models to the data revealed that the adsorption processes followed pseudo-second order reactions and the Langmuir isotherm. SPP achieved a higher maximum adsorption capacity (9.15 mg g−1) than CPPs (5.51 mg g−1). Therefore, sulfonation was considered the most efficient approach to produce a suitable surface functionality for the removal of metal ions from aqueous solutions. However, thermodynamic studies showed that all adsorption processes are spontaneous and feasible (ΔG = − 1.32 and − 1.46 kJ mol−1 at 20 °C for CPP and SPP, respectively), which ensure the possibility of employing acid-derivatized PP microparticles for metal removal. Graphical abstract


  • Sulfonated polypropylene microparticles from waste as adsorbents for methylene blue: Kinetic, equilibrium, and thermodynamic studies

    by Ahmed Bakry, Salwa M. Elmesallamy

    Dyes discharged into waste streams have threatened the lives of aquatic ecosystems and human beings. This work studied the effectiveness of converting polypropylene (PP) waste films into sulfonated microparticles (SPP) for removing methylene blue dye (MB) from aqueous solutions. PP waste was recycled into microparticles (8 µm) and sulfonated in sulfuric acid at 100°C for (6 h). FT-IR analysis proved the existence of sulfonic, carboxylic, and C = C groups on the surface of SPP microparticles. The concentration of acid groups, morphology, surface area, and wettability of SPP were investigated. The effects of the adsorbent dosage, contact time, pH of MB solution, temperature, and ionic strength on the adsorption process were studied. The experimental data of the adsorption process fit well with pseudo-second-order kinetic model and Langmuir isotherm disclosing that the adsorption was chemisorption. A maximum adsorption capacity of 45 mg MB g−1 SPP microparticles was realized at 20°C and neutral pH (6.5). The free energy change showed a negative value reflecting the feasibility and spontaneity of the adsorption process. Accordingly, waste PP can be recycled into a valuable adsorbent for the removal of cationic dyes from polluted water after a proper treatment such as sulfonation. Graphical abstract


  • Open Access

    Nickel hydroxide/polystyrene composites for adsorptive removal of Fe (III) and methylene blue from aqueous solutions

    by Ahmed Bakry, Marzouk Adel, Ahmed El Naggar, Maher H. Helal

    Removal of industrial dyes and metals into water has been considered as a serious environmental problem. To solve this issue, in this study nickel hydroxide/polystyrene composites adsorbents were introduced for the water remediation from the harmful methylene blue dye and Fe (III). Polystyrene was obtained from its monomers using emulsion polymerization technique. The composite was obtained by precipitating nickel hydroxide from its solution on polymer surface by enhancing pH of the medium. The structural and morphological characteristics of the synthesized composites were investigated by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), energetic dispersive X-ray (EDX), and x-ray diffraction (XRD). FT-IR spectra for composites showed the characteristic peaks of polystyrene and that correspond to hydroxide from NiOH2 (3442 cm-1). SEM analysis showed that the Ni(OH)2 were distributed on the surface of polystyrene in a regular manner. EDX analysis showed the presence of 19.9 wt% of Ni on the composite. XRD analysis showed the characteristic diffraction peaks at 2θ = 19.54 corresponding to polystyrene and at 2θ = 32.5, 38.5, 52.1, and 58.97 corresponds to Ni(OH)2. The composite was tested as an adsorbent using the batch technique. The impact of solution pH, contact time, and absorbent dose on the adsorption processes were studied to optimize the operational parameters. Kinetic and equilibrium studies showed that the adsorption processes followed pseudo-first-order kinetic and Freundlich isotherm. Maximum adsorption capacities of 32.73 and 58.24 mg g-1 were achieved in case of MB and Fe (III), respectively. Thermodynamic studies showed that ΔG values for the adsorption processes ranged from -0.075 to -1.435 kJ mol-1 by changing temperature from 303K to 343 in case of MB; ΔG values ranged from -0.467 to -1.548 kJ mol-1 by changing temperature from 303K to 343 in case of Fe (III). Negative values ΔG revealed that the adsorption processes were spontaneous and feasible. Hence, nickel hydroxide/PS composites could be potentially used for treating wastewater from MB and Fe (III).


  • Synergistic effects of surface aminolysis and hydrolysis on improving fibroblast cell colonization within poly(L‐lactide) scaffolds

    by Ahmed Bakry

    This work presents a method for overcoming the low internal cell colonization within the tissue engineering scaffolds. 3D scaffolds were fabricated by the compression molding/salt leaching technique from mixtures of aminolyzed and hydrolyzed poly(L‐lactide) single crystals (PLLAsc) with poly(D,L‐lactide) (PDLLA) microparticles. Modified PLLAsc were used to guarantee the surface hydrophilicity, while PDLLA microparticles were used to reinforce the scaffolds. Mechanical properties, morphology, water uptake and fibroblast cell response of the scaffolds were investigated in comparison with scaffolds from only pristine, hydrolyzed, or aminolyzed PLLAsc. Results showed that the scaffolds exhibited proper morphology and hydrophilicity with an enhanced strength. Water uptake by scaffolds from modified PLLAsc was 1.9 times that from pristine PLLAsc. The scaffolds' compressive moduli increased 2.5 times by using of PDLLA (30 wt%). After cell seeding for a week, the number of cells founded on aminolyzed/hydrolyzed PLLAsc scaffolds were 4.28, 2.14, and 1.36 times that founded for pristine, aminolyzed and hydrolyzed PLLAsc scaffolds, respectively. SEM studies showed that fibroblasts migrated and spread throughout the aminolyzed/hydrolyzed PLLAsc scaffolds better than other scaffolds. Hence, combining both aminolyzed and hydrolyzed PLLAsc with PDLLA could result in a mechanically stable scaffold with an enhanced cell colonization.


  • Core/shell PA6 @ Fe3O4 nanofibers: Magnetic and shielding behavior

    by Mohamed S. A. Darwish, Ahmed Bakry, Laila M. Al-Harbi, Manal M. Khowdiary, A. A. El-Henawy, Jungwon Yoon

    One of the main challenges in the reduction of the electromagnetic wave is to develop lightweight absorber material with a wide absorption frequency. Hence, developing shielding materials that could shield electromagnetic radiation to prevent interference is highly desired for protection. The combination between the unique properties of polyamide (PA6) with free surfactant magnetite nanoparticle as core/shell nanofibers (PA6 @ Fe3O4) provides a promising low-cost, environmentally-friendly and electromagnetic shielding properties. Free surfactant magnetite nanoparticles (39 ± 3.5 nm average size) were prepared by the co-precipitation process and incorporated directly into the polyamide solution before the electrospinning technique. The mean average size of the prepared magnetite nanoparticles is compared based on X-ray diffraction (XRD), dynamic light scattering (DLS), scanning electron microscopy (SEM). The morphology, thermal stability and magnetic behavior of the resultant magnetite nanofibers (150 ± 25 nm average size) were investigated using high-resolution transmission electron microscopy (HRTEM), thermogravimetric analysis (TGA) and vibrating sample magnetometer (VSM), respectively. Shielding effectiveness for magnetite polyamide core/shell nanofibers was measured at frequency 30 MHz–1.5 GHz. The results showed that core/shell nanofibers provide not only well-dispersed magnetite nanoparticles in the polyamide matrix but also controllable sized nanofibers with high magnetization. In addition, even with low magnetite loading of 1.7%, the fabricated nanofiber shows high thermal stability with good performance as electromagnetic shielding nanofiber. Therefore, magnetite polyamide core/shell nanofiber could be considered as a promising material for shielding application.


  • Synergistic effects of surface grafting with heparin and addition of poly(d,l‐lactide) microparticles on properties of poly(l‐lactide) single crystals scaffolds

    by Ahmed Bakry

    Mixtures of heparin grafted poly(l‐lactide) single crystals (Hep‐PLLAsc) and poly(d,l‐lactide) (PDLLA) microparticles are used for assembling hydrophilic and cytocompatible three‐dimensional tissue engineering scaffolds simply by compression molding/salt leaching technique. PLLA is grafted with heparin to promote its surface cytocompatability, while PDLLA is added to reinforce the scaffolds. PLLAsc are aminolyzed with tetraethylenepentamine (13‐atom spacer) to generate sterically accessible amino groups at the surface allowing the covalent attachment of heparin by aqueous carbodiimide chemistry. Morphological and compressive strength studies manifest the integrity and compactness of scaffolds. Toluidine blue assay assures the consistency of heparin distribution throughout the scaffolds, which is in contrary to the conventional grafting reactions by immersing the scaffold in heparin solution. The scaffolds applicability is examined by fibroblast cells seeding experiments. Contrary to pristine scaffolds, Hep‐PLLAsc scaffolds display a hydrophilic and cytocompatible interface for cell adhesion, spreading, growth, and migration. Therefore, combining presurface grafted PLLAsc with PDLLA microparticles could offer durable scaffolds exhibiting bioactive interface and controllable spatial distribution of the grafted biomacromolecules. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47797.


  • Hyaluronic Acid and Chitosan Surface Grafted Polylactide Single Crystals as Hydrophilic Building Blocks for Scaffold Materials

    by Ahmed Bakry, Mohamed S. A. Darwish

    Polylactide has a well-known biocompatibility and processability, but its surface hydrophobicity could limit their use as a proper scaffold for cell growth and proliferation. The present work aims to...