JJJunhyuk Jang

Junhyuk Jang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Junhyuk Jang has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Properties of Cement-Solidified Soils for the Process Control Program

    by Junhyuk Jang, Naon Chang, Sung-Wook Kim, Junyoung Jung, Dong-Su Kim

    The performance of cement-solidified soil waste was evaluated following Process Control Program (PCP) guidelines. Illite-based soils were used as surrogate for radioactive soil waste. The optimal mixing ratio of water, cement, and waste was determined from compression strength and workability; the solidified block at a mixing ratio of 25 wt.% water, 50 wt.% soil, and 25 wt.% cement exhibited 12.7 MPa of compression strength with good workability. Cement-solidified soil blocks in PCP size (diameter: 100 mm; height: 200 mm) were fabricated at the determined mixing ratio. Compression, immersion, thermal cycling, and irradiation tests were performed on the solidified blocks. The cement-solidified blocks passed the acceptance KORAD criteria for disposal, satisfying a compression strength above 3.44 MPa after all tests. Leaching tests were performed by piking radioactive natural soils (39.36 Bq/g), showing no radioactivity. These results suggest that radioactive soil waste can be solidified with cement by following PCP guidelines.

  • Open Access

    Thermochemical Decontamination of Paper Wiper Wastes through Combined Carbonization and Chlorination

    by Sung-Wook Kim, Min Ku Jeon, Junhyuk Jang, Maengkyo Oh

    Chlorination has been used for the thermochemical decontamination of radioactive waste to address the significant amount of waste in nuclear facilities. Control of chlorination conditions is essential to optimize decontamination efficiency, as these conditions significantly influence chemical and physical evolution of target waste. In this study, the feasibility of thermochemical decontamination for reducing the radioactivity of paper wiper waste was investigated. A two-step thermochemical process, comprising low-temperature carbonization and high-temperature chlorination, was suggested to improve the decontamination efficiency. Simulated paper wiper waste contaminated with Cs and Co was treated in a closed system filled with air at 250°C for carbonization as a pretreatment. Subsequently, the partial carbonization product was chlorinated at 700–900°C to remove Cs and Co. Decontamination efficiencies of more than 99% were obtained after the two-step thermochemical process.

  • Open Access

    Surface Stability and Electrochemical Behavior of Additively Manufactured Copper in Repository-Relevant Environments

    by Jeong-Hyun Woo, Gha-Young Kim, Junhyuk Jang, Seok Yoon, Young-Ho Lee, Yang-Il Jung, Younghoon Kim, Ju-Young Kim, Yakai Zhao

    The long-term stability of disposal canisters is determined by their corrosion resistance in deep geological disposal environments. This study investigates the surface stability, electrochemical behavior, and mechanical properties of wire arc additively manufactured (WAAM) Cu and Cu alloys compared to forged oxygen-free copper (OFC) in repository-relevant groundwater. Electrochemical and surface characterizations in aerobic and anaerobic groundwater conditions were correlated with nanoindentation results. Under aerobic conditions, all materials exhibited comparable corrosion behavior with predominantly uniform corrosion. In contrast, under anaerobic conditions, AM-Cu showed higher corrosion current densities than OFC, associated with heterogeneous surface reactions. In sulfide-containing environment, the corrosion current density of OFC was approximately 3.5 times lower than AM-Cu, despite the formation of a denser Cu2S layer on AM-Cu. Tafel analysis further revealed a gradual increase of current density in anodic region, indicating instability of the CuCl- derived surface film compared to the stable response of OFC. Nanoindentation results showed that AM-Cu possesses higher hardness and elastic modulus than OFC, indicating a trade-off between mechanical strengthening and electrochemical stability. These findings demonstrate that process-induced heterogeneity in AM-Cu governs corrosion film evolution and electrochemical behavior under repository-relevant environments.

  • Open Access

    Characterization of Compacted Ca- and Na-Bentonite with Copper Corrosion Products in the KAERI Underground Research Tunnel

    by Mihye Kong, Minsoo Lee, Gha-Young Kim, Junhyuk Jang, Jin-Seop Kim

    In a deep geological disposal system, bentonite buffer material is an important barrier used to protect the disposal canister from the inflow of groundwater and prevent the outflow of radionuclides. This study aimed to characterize the mineralogical and chemical reactions of bentonite caused by copper corrosion of the canister in a radioactive waste repository. We investigated the d-spacings of montmorillonite in Gyeongju bentonite (Ca-type, KJ-I) under groundwater-saturated conditions over 10 years and compared their characteristics with those of Wyoming bentonite (Na-type, MX-80) in the Korea Atomic Energy Research Institute Underground Research Tunnel. Mineralogical investigations using X-ray diffraction and focused ion beam energy-dispersive spectroscopy indicated that no transformation of smectite or neo-formed clay phases occurred. In the Ca-type bentonite (KJ-I), the swelling was observed when it was in contact with rolled plate (RP) and cold-spray-coated (CSC) copper, with d-spacing expansions of 2.9% and 3.8%, respectively. In contrast, the Na-type bentonite (MX-80) showed d-spacing expansions of 17.6% and 19.6% when it was in contact with the RP and CSC Cu, respectively. The Cu concentration and distribution indicated that the corrosion products dissolved and then diffused into the surrounding bentonite, with maximum penetration depths of 2.0 and 0.5 mm over 10 years, respectively.


  • Open Access

    Investigation of Early Corrosion Behavior of Canister Candidate Materials in Oxic Groundwater by the EQCM Method

    by Gha-Young Kim, Sung-Wook Kim, Junhyuk Jang, Seok Yoon, Jin-Seop Kim

    This study investigated the corrosion mass changes of canister candidate materials (Cu, Ni, Ti, SS304) in an oxic groundwater solution using the electrochemical quartz crystal microbalance method in order to estimate corrosion thickness. The materials were immersed in naturally aerated groundwater with and without the addition of chloride ions to observe the mass changes as well as the open-circuit potential (corrosion potential). In the oxic groundwater solution, Ni, Ti, and SS304 exhibited negligible mass changes, indicating their insusceptibility to general corrosion. In contrast, the Cu electrode exhibited a relatively significant mass change (63.8 ng/cm2 for 60 h), and the maximum corrosion thickness was estimated to be approximately 0.1 μm/yr. In the presence of chloride ions, the Ni and Ti electrodes did not reveal demonstrate any significant changes, whereas the SS304 electrode was slightly increased compared to an absence of chloride ions. A lower mass change occurred when the Cu electrode was immersed in the chloride-containing groundwater solution compared with the absence of chlorides because the dissolution of Cu as was involved in Cu2O formation.


  • Open Access

    Effect of Chloride Ions on Electrochemical Behavior of Canister Materials

    by Gha-Young Kim, Junhyuk Jang, Minsoo Lee, Jin-Seop Kim

    Various canister candidate materials (SS316L, Ti-Gr.2, Alloy 22, and Cu) were studied using groundwater at the Korea Atomic Energy Research Institute (KAERI) underground research tunnel (KURT), with the addition of chloride ions using different electrochemical techniques. The corrosion potential and corrosion current of test materials were obtained by the polarization measurement. The polarization measurements revealed that the addition of chloride ions was detrimental to the SS316L and Cu materials by increasing corrosion current, which is an indicator of corrosion rate. Impedance measurements and fitting analysis showed that the corrosion resistance of Cu was more than 10 times lower than that of other materials in the KURT groundwater solution containing 0.1 M of chloride ions.


  • Open Access

    Designs of Corrosion Modules for Long-Term Corrosion Tests of Canister Materials in Aerobic and Anaerobic Underground Water

    by Junhyuk Jang, Minsoo Lee, Gha-Young Kim, Mihye Kong, Jin-Seop Kim

    Corrosion modules simulating the engineered barrier system were designed for long-term corrosion (LTC) testing of canister materials under aerobic and anaerobic conditions. The LTC module for aerobic conditions was designed as a bath-type container flowing underground water from Korea Underground Research Tunnel. Rolled Cu, stainless steel 304 (SS), Ti-grade 2, cast iron, and Cu coatings were embedded into bentonites. After three years of testing under aerobic conditions, the corrosion rate of Cu was estimated to be 550 nm/year. The LTC module for anaerobic conditions was developed in a vessel-type cylindrical container to settle into boreholes. Four coin-shaped samples of each metal were embedded in bentonite, which was subsequently stacked in a cylindrical vessel. The vessels were placed in boreholes at a depth of 300 m. Retrieving modules at an early stage of the LTC test for six months under anaerobic conditions revealed a Cu corrosion rate of 280 nm/year.