Emanuele Parisi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Emanuele Parisi has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Giampiero de Cesare
INFN Sezione di Roma 1, Piazzale Aldo Moro 2, Roma
7 shared publications - Domenico Caputo
Department of Information Engineering, Electronics and Telecommunications, Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
6 shared publications - Nicola Lovecchio
Department of Information Engineering, Electronics and Telecommunications, Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
5 shared publications - Augusto Nascetti
School of Aerospace Engineering, Sapienza University of Rome, Via Salaria 851, 00138 Rome, Italy
4 shared publications - Giulia Petrucci
Department of Information, Electronics and Communication Engineering, University of Rome "La Sapienza", Via Eudossiana 18, 00184, Rome, Italy
3 shared publications - Mario Tucci
ENEA Research Center Casaccia
3 shared publications
Latest Publications
- 11 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 12 (6) , 1337-1344
Integrated Optoelectronic Device for Detection of Fluorescent Molecules
This paper presents the development of a compact optoelectronic device suitable for on-chip detection of fluorescent molecules. In order to obtain a highly integrated device, a long-pass multi-dielectric filter has been integrated with thin-film amorphous silicon photosensors on a single glass substrate. Filter rejects the excitation light, allowing the reduction of the distance between the source and the fluorescent site and avoiding the use of external optical component. The compatibility of the technological processes determined the materials and the temporal sequence of the device fabrication. The developed device has been designed for the fluorescence detection of ruthenium complex based molecules and tested, as a proof of concept, for the detection of double-stranded DNA down to 0.5 ng. Results demonstrate the correct operation of the integrated system in both rejecting the excitation light and in detecting the fluorescent signal, demonstrating the suitability of this optoelectronic platform in practical biomedical applications.
- 11 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 12 (6) , 1337-1344
Integrated Optoelectronic Device for Detection of Fluorescent Molecules
This paper presents the development of a compact optoelectronic device suitable for on-chip detection of fluorescent molecules. In order to obtain a highly integrated device, a long-pass multi-dielectric filter has been integrated with thin-film amorphous silicon photosensors on a single glass substrate. Filter rejects the excitation light, allowing the reduction of the distance between the source and the fluorescent site and avoiding the use of external optical component. The compatibility of the technological processes determined the materials and the temporal sequence of the device fabrication. The developed device has been designed for the fluorescence detection of ruthenium complex based molecules and tested, as a proof of concept, for the detection of double-stranded DNA down to 0.5 ng. Results demonstrate the correct operation of the integrated system in both rejecting the excitation light and in detecting the fluorescent signal, demonstrating the suitability of this optoelectronic platform in practical biomedical applications.
- 9 September 2017
- Published by Springer Nature in Lecture Notes in Electrical Engineering
- p. 121-127
Integration of Amorphous Silicon Photosensors with Thin Film Interferential Filter for Biomolecule Detection
- 9 September 2017
- Published by Springer Nature in Lecture Notes in Electrical Engineering
- p. 121-127
Integration of Amorphous Silicon Photosensors with Thin Film Interferential Filter for Biomolecule Detection
- Open Access
- 1 January 2016
- Published by Elsevier in Procedia Engineering
- Vol. 168, 1434-1437
Integration of Amorphous Silicon Balanced Photodiodes and Thin Film Heaters for Biosensing Application
- 1 January 2016
- Published by Elsevier in Procedia Engineering
- Vol. 168, 1434-1437
Open AccessIntegration of Amorphous Silicon Balanced Photodiodes and Thin Film Heaters for Biosensing Application
- 1 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 277-282
Thermal control system based on thin film heaters and amorphous silicon diodes
In this paper we present a system able to perform thermal treatments on lab-on-chip devices fabricated on glass substrates. The system includes a thin film resistor acting as heater and thin film hydrogenated amorphous silicon diodes acting as temperature sensors. An electronic system controls the lab-on-chip temperature through a Proportional-IntegralDerivative algorithm. In particular, an electronic board infers the system temperature measuring the voltage across the amorphous silicon diodes and drives the heater to achieve the set-point temperature. Taking into account the 16-bit ADC resolution and the sensors sensitivity, which is around 3.6 mV/ o C, we estimate that our system is able to detect temperature variation as low as 3.5·10 -3o C. Furthermore, the experimental results show that the system is able to stabilize the system temperature with a precision better than 0.1 o C.
- 1 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 277-282
Thermal control system based on thin film heaters and amorphous silicon diodes
In this paper we present a system able to perform thermal treatments on lab-on-chip devices fabricated on glass substrates. The system includes a thin film resistor acting as heater and thin film hydrogenated amorphous silicon diodes acting as temperature sensors. An electronic system controls the lab-on-chip temperature through a Proportional-IntegralDerivative algorithm. In particular, an electronic board infers the system temperature measuring the voltage across the amorphous silicon diodes and drives the heater to achieve the set-point temperature. Taking into account the 16-bit ADC resolution and the sensors sensitivity, which is around 3.6 mV/ o C, we estimate that our system is able to detect temperature variation as low as 3.5·10 -3o C. Furthermore, the experimental results show that the system is able to stabilize the system temperature with a precision better than 0.1 o C.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Multilayer integrated structure for selective detection of Ochratoxin A
This work presents the design, fabrication and characterization of a system based on thin film technology for the selective detection of the natural fluorescence of Ochratoxin A. To this aim, the system optically couples an amorphous silicon photosensor with a long pass multi-dielectric filter, deposited on glass substrates. In particular, the filter rejects the wavelengths coming from the excitation source (centered at 340 nm) and transmits the emission spectrum (centered at 465 nm) of the mycotoxin, reducing therefore the background noise. The basic structure of the a-Si:H photosensors is a p-type/intrinsic/n-type stacked junction, deposited by Plasma Enhanced Chemical Vapor Deposition at temperatures ranging from 210 to 300 °C. Its responsivity at 465 nm is equal to 185 mA/W. The long pass filter is an interferential filter, constituted by alternating layers of TiO 2 and SiO 2 . It has been designed by using a freeware software, and deposited by electron beam Physical Vapor Deposition at 250 °C. A very good agreement between modeled and experimental data of transmittance and reflectance has been achieved. In particular, transmittance of the filter varies by almost four orders of magnitude between 360 nm and 400 nm, showing its suitability in rejecting the excitation light.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Multilayer integrated structure for selective detection of Ochratoxin A
This work presents the design, fabrication and characterization of a system based on thin film technology for the selective detection of the natural fluorescence of Ochratoxin A. To this aim, the system optically couples an amorphous silicon photosensor with a long pass multi-dielectric filter, deposited on glass substrates. In particular, the filter rejects the wavelengths coming from the excitation source (centered at 340 nm) and transmits the emission spectrum (centered at 465 nm) of the mycotoxin, reducing therefore the background noise. The basic structure of the a-Si:H photosensors is a p-type/intrinsic/n-type stacked junction, deposited by Plasma Enhanced Chemical Vapor Deposition at temperatures ranging from 210 to 300 °C. Its responsivity at 465 nm is equal to 185 mA/W. The long pass filter is an interferential filter, constituted by alternating layers of TiO 2 and SiO 2 . It has been designed by using a freeware software, and deposited by electron beam Physical Vapor Deposition at 250 °C. A very good agreement between modeled and experimental data of transmittance and reflectance has been achieved. In particular, transmittance of the filter varies by almost four orders of magnitude between 360 nm and 400 nm, showing its suitability in rejecting the excitation light.
- 1 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Thermal characterization of thin film heater for lab-on-chip application
This paper presents the design, fabrication and characterization of a thin film heater functional for thermal treatments in lab-on-chip system. The spatial temperature distribution determined by different heater geometries has been studied through electro-thermal simulations by using COMSOL Multiphysics. The heater showing the more uniform temperature distribution has been subsequently fabricated and characterized. A very good agreement between modeled and measured data has been attained. Results show a spatial temperature distribution of about ±1°C over an area comparable to the heater area and a directly USB powered heater, demonstrating the suitability of the proposed device for lab-on-chip thermal applications.
- 1 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Thermal characterization of thin film heater for lab-on-chip application
This paper presents the design, fabrication and characterization of a thin film heater functional for thermal treatments in lab-on-chip system. The spatial temperature distribution determined by different heater geometries has been studied through electro-thermal simulations by using COMSOL Multiphysics. The heater showing the more uniform temperature distribution has been subsequently fabricated and characterized. A very good agreement between modeled and measured data has been attained. Results show a spatial temperature distribution of about ±1°C over an area comparable to the heater area and a directly USB powered heater, demonstrating the suitability of the proposed device for lab-on-chip thermal applications.
- 1 December 2014
- Published by Elsevier in Microelectronics Journal
- Vol. 45 (12) , 1684-1690
Polydimethylsiloxane material as hydrophobic and insulating layer in electrowetting-on-dielectric systems
- 1 December 2014
- Published by Elsevier in Microelectronics Journal
- Vol. 45 (12) , 1684-1690
Polydimethylsiloxane material as hydrophobic and insulating layer in electrowetting-on-dielectric systems