Ibrahim Akkaya
Research Subjects
Ibrahim Akkaya has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Mehmet Engin
5 shared publicationsErkan Zeki Engin
Elektrik ve Elektronik Mhendislii Blm, EGE niversitesi, zmir, Trkiye
3 shared publications- Yavuz Öztürk
Ege Universitesi
3 shared publications - Mehmet Engin
Ege University
2 shared publications Ali Hakan Işik
1 shared publication- Andrea Cogliati
Department of Electrical and Computer Engineering, University of Rochester, Rochester, NY, USA
1 shared publication
Latest Publications
- Open Access
- 1 May 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (9) , 095343
Optical coherence tomography-based deep regression framework for precise estimation of directional and geometric contact angles on polymeric surfaces
Accurate and automated characterization of surface wettability is essential for optical sensing, material inspection, and polymer surface engineering. Conventional contact angle (CA) measurements rely on 2D side-view imaging and manual contour fitting, which introduce user-dependent variability and limit throughput. This study presents an intelligent optical coherence tomography (OCT)-based sensing framework that integrates OCT with a convolutional neural network (CNN) regression for simultaneous estimation of four CA metrics—left, right, circular, and elliptical—directly from volumetric cross-sectional data. Multi-output and single-output regression models were trained and compared in terms of accuracy and computational efficiency. The multi-output model achieved R 2 > 0.92 across all CA types, while single-output models achieved R 2 = 0.93–0.96 with reduced variance. Experimental validation confirmed that the proposed OCT-enabled CNN framework accurately resolves the droplet–surface interface and meniscus curvature without manual edge detection, geometric fitting, or engineered features. The results demonstrate a fully automated, depth-resolved, and high-throughput optical sensing approach for quantitative wettability characterization of polymeric materials, offering a robust solution for next-generation intelligent surface measurement systems.
- 1 May 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (9) , 095343
Open AccessOptical coherence tomography-based deep regression framework for precise estimation of directional and geometric contact angles on polymeric surfaces
Accurate and automated characterization of surface wettability is essential for optical sensing, material inspection, and polymer surface engineering. Conventional contact angle (CA) measurements rely on 2D side-view imaging and manual contour fitting, which introduce user-dependent variability and limit throughput. This study presents an intelligent optical coherence tomography (OCT)-based sensing framework that integrates OCT with a convolutional neural network (CNN) regression for simultaneous estimation of four CA metrics—left, right, circular, and elliptical—directly from volumetric cross-sectional data. Multi-output and single-output regression models were trained and compared in terms of accuracy and computational efficiency. The multi-output model achieved R 2 > 0.92 across all CA types, while single-output models achieved R 2 = 0.93–0.96 with reduced variance. Experimental validation confirmed that the proposed OCT-enabled CNN framework accurately resolves the droplet–surface interface and meniscus curvature without manual edge detection, geometric fitting, or engineered features. The results demonstrate a fully automated, depth-resolved, and high-throughput optical sensing approach for quantitative wettability characterization of polymeric materials, offering a robust solution for next-generation intelligent surface measurement systems.
- 15 October 2023
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 6 (4) , 369-374
LED based Low-Cost Photo-Acoustic Setup by Using Stethoscope
In this study, design and characterization of a low-cost photo-acoustic setup is presented. Photo-acoustic effect is a very intriguing photo-thermo-acoustic effect having applications in a wide range from biomedical science to material characterization. The basic components of a photo-acoustic setup are a sound detector with or without an acoustic cell, a modulated light source preferably with enough power, and an absorbing object. One of the challenging problems is to couple the produced photo-acoustic waves into the detector and this problem was solved by using a commercial sound sensor module connected to a stethoscope. As a modulated light source simply a high power flashlight driven with an amplifier and MOSFET circuit was used. Both detection and light modulation were designed and operated to be via sound card input/output (I/O) of a computer and/or cell phone. Light power and frequency response of the system were presented and 523 Hz was determined as a resonance frequency of the system.
- 15 October 2023
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 6 (4) , 369-374
LED based Low-Cost Photo-Acoustic Setup by Using Stethoscope
In this study, design and characterization of a low-cost photo-acoustic setup is presented. Photo-acoustic effect is a very intriguing photo-thermo-acoustic effect having applications in a wide range from biomedical science to material characterization. The basic components of a photo-acoustic setup are a sound detector with or without an acoustic cell, a modulated light source preferably with enough power, and an absorbing object. One of the challenging problems is to couple the produced photo-acoustic waves into the detector and this problem was solved by using a commercial sound sensor module connected to a stethoscope. As a modulated light source simply a high power flashlight driven with an amplifier and MOSFET circuit was used. Both detection and light modulation were designed and operated to be via sound card input/output (I/O) of a computer and/or cell phone. Light power and frequency response of the system were presented and 523 Hz was determined as a resonance frequency of the system.
- Open Access
- 28 March 2023
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 19 (1) , 31-37
Tissue Mimicking Phantom Design and Characterization for Thermal Imaging Applications on Medical Diagnosis
Breast cancer is one of the mortal cancerous for women and an early diagnosis, applying an appropriate treatment and prognosis increases the survival chance of the patients. There are different screening methods and thermal imaging is one of the noninvasive promising diagnosis techniques to detect thermal profile anomalies in breasts. This work includes both simulation and experimental studies for the detection of breast tumors by using thermal images. The first step is the simulation studies based on heat transfer in biological tissues. By using the Bio-Heat transfer theory, temperature differences between the healthy and tumorous tissues are acquired. The second step consists of phantom designs and detection of breast tumor via thermographic imaging in in-vitro. Designing an appropriate phantom is tremendously crucial for the calibration of the thermal imaging system and diagnosis of breast cancer. As a result of the study, it is presented that the detection of temperatures difference especially with asymmetry factor between the tumor and healthy tissue region is feasible. Also, it is shown that the simulation based results are consistent with the experimental as well.
- 28 March 2023
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 19 (1) , 31-37
Open AccessTissue Mimicking Phantom Design and Characterization for Thermal Imaging Applications on Medical Diagnosis
Breast cancer is one of the mortal cancerous for women and an early diagnosis, applying an appropriate treatment and prognosis increases the survival chance of the patients. There are different screening methods and thermal imaging is one of the noninvasive promising diagnosis techniques to detect thermal profile anomalies in breasts. This work includes both simulation and experimental studies for the detection of breast tumors by using thermal images. The first step is the simulation studies based on heat transfer in biological tissues. By using the Bio-Heat transfer theory, temperature differences between the healthy and tumorous tissues are acquired. The second step consists of phantom designs and detection of breast tumor via thermographic imaging in in-vitro. Designing an appropriate phantom is tremendously crucial for the calibration of the thermal imaging system and diagnosis of breast cancer. As a result of the study, it is presented that the detection of temperatures difference especially with asymmetry factor between the tumor and healthy tissue region is feasible. Also, it is shown that the simulation based results are consistent with the experimental as well.
- 9 December 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11924, 32-34
An 18.6 MHz wavelength-swept laser source based on stretched-pulse mode-locking at 1290 nm
We present a stretched-pulse mode-locked (SPML) wavelength-swept laser source at 1290 nm. The lasing bandwidth of the source was 80 nm at a sweep rate of ~18.6 MHz.
- 9 December 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11924, 32-34
An 18.6 MHz wavelength-swept laser source based on stretched-pulse mode-locking at 1290 nm
We present a stretched-pulse mode-locked (SPML) wavelength-swept laser source at 1290 nm. The lasing bandwidth of the source was 80 nm at a sweep rate of ~18.6 MHz.
- 20 February 2020
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11238, 1123816-41
A pilot study: infrared laser stimulation of the rat vagus nerves
The vagus nerve originating from the brainstem in the central nervous system is a long cranial nerve that reaches the neck, thorax, abdomen, and colon. It plays a role in autonomic nervous, cardiovascular, gastrointestinal, and immune systems. Electrical stimulation of the vagus nerve has become a standard method for the treatment of neuropathic pain and epileptic conditions over the years. Infrared laser nerve stimulation (ILNS) is an evolving technique that uses infrared laser energy to stimulate cells with electrochemical capacity without the need for external agents or physical contact. This pilot study explores infrared laser stimulation of the rat vagus nerve, in-vivo. An infrared pigtailed singlemode diode laser operating at 1505 nm in continuous-wave (CW) mode was used in this study for noncontact CW-ILNS. Successful CW-ILNS of the rat vagus nerve was observed after the CN reached a threshold temperature of ~44°C with response times as short as 10 s. With more improvement in instrumentation, better optimization of stimulation parameters, and a higher sample size, CW-ILNS may show some potential in vagus nerve stimulation for preclinical.
- 20 February 2020
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11238, 1123816-41
A pilot study: infrared laser stimulation of the rat vagus nerves
The vagus nerve originating from the brainstem in the central nervous system is a long cranial nerve that reaches the neck, thorax, abdomen, and colon. It plays a role in autonomic nervous, cardiovascular, gastrointestinal, and immune systems. Electrical stimulation of the vagus nerve has become a standard method for the treatment of neuropathic pain and epileptic conditions over the years. Infrared laser nerve stimulation (ILNS) is an evolving technique that uses infrared laser energy to stimulate cells with electrochemical capacity without the need for external agents or physical contact. This pilot study explores infrared laser stimulation of the rat vagus nerve, in-vivo. An infrared pigtailed singlemode diode laser operating at 1505 nm in continuous-wave (CW) mode was used in this study for noncontact CW-ILNS. Successful CW-ILNS of the rat vagus nerve was observed after the CN reached a threshold temperature of ~44°C with response times as short as 10 s. With more improvement in instrumentation, better optimization of stimulation parameters, and a higher sample size, CW-ILNS may show some potential in vagus nerve stimulation for preclinical.
- Open Access
- 1 November 2018
- Published by World Scientific Pub Co Pte Ltd in Journal of Innovative Optical Health Sciences
- Vol. 11 (06)
Power spectral density-based nearinfrared sub-band detection for noninvasive blood glucose prediction in both in-vitro and in-vivo studies
- 1 November 2018
- Published by World Scientific Pub Co Pte Ltd in Journal of Innovative Optical Health Sciences
- Vol. 11 (06)
Open AccessPower spectral density-based nearinfrared sub-band detection for noninvasive blood glucose prediction in both in-vitro and in-vivo studies
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Plasma frequency selective surface for GNSS applications
We propose a low-cost and reconfigurable plasma frequency selective surface (PFSS) with fluorescent lamps for Global Navigation Satellite System (GNSS) applications. Although many antenna topologies exist for broadband operation, antennas with plasma frequency selective surfaces are limited and offer certain advantages. Especially for GNSS applications, antenna performance can be demanding given the limited space for the antenna. In almost all GNSS antennas, a perfect electric conductor (PEC) ground is utilized. In this study, we compare PEC and PFSS reflectors over entire GNSS bandwidth. We believe PFSS structure can not only provide the benefits of PEC ground but also lower antenna profile.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Plasma frequency selective surface for GNSS applications
We propose a low-cost and reconfigurable plasma frequency selective surface (PFSS) with fluorescent lamps for Global Navigation Satellite System (GNSS) applications. Although many antenna topologies exist for broadband operation, antennas with plasma frequency selective surfaces are limited and offer certain advantages. Especially for GNSS applications, antenna performance can be demanding given the limited space for the antenna. In almost all GNSS antennas, a perfect electric conductor (PEC) ground is utilized. In this study, we compare PEC and PFSS reflectors over entire GNSS bandwidth. We believe PFSS structure can not only provide the benefits of PEC ground but also lower antenna profile.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Estimation of oxygen saturation with laser optical imaging method
The aim of this study is to determine the estimation of hemoglobin concentration and oxygen saturation of tissue by non-invasively functional laser imaging for early skin cancer diagnosis. The early diagnosis of melanoma is a key factor that remarkably reduces the mortality rate. Diffuse reflectance spectroscopy is a very useful device for diagnosis and treatment purposes under in-vivo conditions. At this point, the aforementioned device, which takes into account the scattering of tissue, is to determine the concentration of chromophores (or optical absorbers) due to attenuated light strikes to the superficial layer of tissue. Laser-type light based imaging techniques in medical diagnosis substantially produce good results. So the aim of this study is to estimate HbO2 % and Hb% concentrations.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Estimation of oxygen saturation with laser optical imaging method
The aim of this study is to determine the estimation of hemoglobin concentration and oxygen saturation of tissue by non-invasively functional laser imaging for early skin cancer diagnosis. The early diagnosis of melanoma is a key factor that remarkably reduces the mortality rate. Diffuse reflectance spectroscopy is a very useful device for diagnosis and treatment purposes under in-vivo conditions. At this point, the aforementioned device, which takes into account the scattering of tissue, is to determine the concentration of chromophores (or optical absorbers) due to attenuated light strikes to the superficial layer of tissue. Laser-type light based imaging techniques in medical diagnosis substantially produce good results. So the aim of this study is to estimate HbO2 % and Hb% concentrations.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Representative wavelength determination/investigation in the near infrared region for optical measuring of the human blood glucose
In this study, the phantom mediums which has different optical characteristic were made for detecting of glucose level, then the transmittance based measurements were done. It was studied between 900-2500 nm wavelength which includes higher absorption bands of glucose. An index parameter was improved and used a windowing based method for determining the glucose amount. The correlation was searched between the acquired index parameter and glucose concentrations, and a sensitive wavelength was found for glucose estimation. From the results, 1322-1338 nm were found meaningful for this purpose. In addition, 2144-2165 nm are also found alternative or supplemental wavelengths.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Representative wavelength determination/investigation in the near infrared region for optical measuring of the human blood glucose
In this study, the phantom mediums which has different optical characteristic were made for detecting of glucose level, then the transmittance based measurements were done. It was studied between 900-2500 nm wavelength which includes higher absorption bands of glucose. An index parameter was improved and used a windowing based method for determining the glucose amount. The correlation was searched between the acquired index parameter and glucose concentrations, and a sensitive wavelength was found for glucose estimation. From the results, 1322-1338 nm were found meaningful for this purpose. In addition, 2144-2165 nm are also found alternative or supplemental wavelengths.