Mehdi Heidari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mehdi Heidari has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Jiwang Yan
Department of Mechanical Engineering Faculty of Science and Technology Keio University Yokohama Japan
6 shared publications - Seyed Vahid Hosseini
Faculty of Mechanical Engineering, Shahrood University of Technology, Shahrood, Iran
4 shared publications - Hadi Parvaz
Faculty of Mechanical and Mechatronics Engineering, Shahrood University of Technology, Shahrood, Iran
3 shared publications - Mohammad Jafari
Shahrood University of Technology
2 shared publications A. Erfani-Moghadam
Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
1 shared publicationAbolfazl Talebi
Faculty of Mechanical and Mechatronics Engineering, Shahrood University of Technology, Shahrood, Iran
1 shared publication
Latest Publications
- 19 September 2026
- Published by SAGE Publications in Journal of Composite Materials
The effect of silica nanoparticles on machining and mechanical properties of phenolic resol/short glass fiber nanocomposite
This study investigates the influence of SiO 2 nanoparticles on the mechanical properties and drilling performance of phenolic resol/short glass fiber (PF/GF) composites. Nanocomposites containing 0, 1, and 3 wt% SiO 2 were fabricated using compression molding under controlled conditions. The results show that the addition of nanoparticles significantly enhances composite performance. The sample with 3 wt% SiO 2 exhibited approximately 15% higher tensile strength compared to the neat composite. In addition, the delamination factor during drilling decreased noticeably, indicating improved machinability. SEM observations confirmed improved fiber–matrix adhesion and reduced interfacial defects due to nanoparticle incorporation. The findings demonstrate that nano-SiO 2 reinforcement can effectively improve both structural integrity and machining quality of PF/GF composites, making them more suitable for engineering applications requiring secondary machining operations.
- 19 September 2026
- Published by SAGE Publications in Journal of Composite Materials
The effect of silica nanoparticles on machining and mechanical properties of phenolic resol/short glass fiber nanocomposite
This study investigates the influence of SiO 2 nanoparticles on the mechanical properties and drilling performance of phenolic resol/short glass fiber (PF/GF) composites. Nanocomposites containing 0, 1, and 3 wt% SiO 2 were fabricated using compression molding under controlled conditions. The results show that the addition of nanoparticles significantly enhances composite performance. The sample with 3 wt% SiO 2 exhibited approximately 15% higher tensile strength compared to the neat composite. In addition, the delamination factor during drilling decreased noticeably, indicating improved machinability. SEM observations confirmed improved fiber–matrix adhesion and reduced interfacial defects due to nanoparticle incorporation. The findings demonstrate that nano-SiO 2 reinforcement can effectively improve both structural integrity and machining quality of PF/GF composites, making them more suitable for engineering applications requiring secondary machining operations.
- 16 September 2026
- Published by Springer Nature in Journal of Molecular Modeling
- Vol. 32 (10) , 373
Tool wear mechanism in diamond tools of single-crystal silicon machining: a molecular dynamics study
- 16 September 2026
- Published by Springer Nature in Journal of Molecular Modeling
- Vol. 32 (10) , 373
Tool wear mechanism in diamond tools of single-crystal silicon machining: a molecular dynamics study
- 19 November 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4) , 045587
Diamond tool life and surface integrity during ultra-precision machining of single-crystal silicon
Ultra-precision machining of single-crystal silicon using single-point diamond turning (SPDT) is essential for fabricating high-precision optical and microelectronic components. This process offers superior surface quality and dimensional accuracy compared to traditional machining methods. However, diamond tool wear and its impact on surface integrity pose significant challenges. This research investigates the effects of machining parameters on diamond tool wear mechanisms and surface integrity in SPDT of single-crystal silicon. The Taguchi experimental design methodology was employed to analyze machining parameters, including depth of cut, feed rate, and spindle speed. Surface integrity was assessed from two perspectives: topography, characterized by surface roughness and microscopic damage, and material phase transformations, which were analyzed via subsurface crystal lattice amorphization. Surface roughness served as the stopping criterion for each machining test, and tool wear characteristics were examined using field emission scanning electron microscopy (FESEM). The results revealed that the maximum undeformed chip thickness ( h max ) played a crucial role in tool wear behavior. An optimal h max value was identified to achieve extended tool life and superior surface quality. X-ray diffraction (XRD) and Raman spectroscopy were applied to characterize material phase transformations and subsurface layer modifications induced by machining, demonstrating that increasing cutting speed from 0.26 m s −1 to 2.51 m s −1 progressively decreased amorphous layer thickness, as evidenced by Raman peak intensities at 521 cm −1 and diminished amorphous peaks at 470 cm −1 ; this mitigated abrasive wear on the diamond tool and improved surface finish. This study established an optimal undeformed chip thickness ( h max ) of 106 nm for maximizing tool life and surface integrity in SPDT of single-crystal silicon.
- 19 November 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4) , 045587
Diamond tool life and surface integrity during ultra-precision machining of single-crystal silicon
Ultra-precision machining of single-crystal silicon using single-point diamond turning (SPDT) is essential for fabricating high-precision optical and microelectronic components. This process offers superior surface quality and dimensional accuracy compared to traditional machining methods. However, diamond tool wear and its impact on surface integrity pose significant challenges. This research investigates the effects of machining parameters on diamond tool wear mechanisms and surface integrity in SPDT of single-crystal silicon. The Taguchi experimental design methodology was employed to analyze machining parameters, including depth of cut, feed rate, and spindle speed. Surface integrity was assessed from two perspectives: topography, characterized by surface roughness and microscopic damage, and material phase transformations, which were analyzed via subsurface crystal lattice amorphization. Surface roughness served as the stopping criterion for each machining test, and tool wear characteristics were examined using field emission scanning electron microscopy (FESEM). The results revealed that the maximum undeformed chip thickness ( h max ) played a crucial role in tool wear behavior. An optimal h max value was identified to achieve extended tool life and superior surface quality. X-ray diffraction (XRD) and Raman spectroscopy were applied to characterize material phase transformations and subsurface layer modifications induced by machining, demonstrating that increasing cutting speed from 0.26 m s −1 to 2.51 m s −1 progressively decreased amorphous layer thickness, as evidenced by Raman peak intensities at 521 cm −1 and diminished amorphous peaks at 470 cm −1 ; this mitigated abrasive wear on the diamond tool and improved surface finish. This study established an optimal undeformed chip thickness ( h max ) of 106 nm for maximizing tool life and surface integrity in SPDT of single-crystal silicon.
- 18 December 2021
- Published by Springer Nature in Sādhanā
- Vol. 47 (1) , 1-12
Molecular dynamics investigation into the effect of nano-void size on cutting parameters in copper single crystal
- 18 December 2021
- Published by Springer Nature in Sādhanā
- Vol. 47 (1) , 1-12
Molecular dynamics investigation into the effect of nano-void size on cutting parameters in copper single crystal
- Open Access
- 5 November 2021
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 16 (11) , e0259401
Effect of nano clay, nano-graphene oxide and carbon nanotubes on the mechanical and tribological properties of crosslinked epoxy nanocomposite
The objective of this study is to investigate the effects of different nanoparticles as reinforcement in a polymeric matrix on the mechanical and tribological properties of the composite. The different particles including nanoclay (NC), nano-graphene oxide (NGO), and carbon nanotubes (CNT) with various weight percentages were incorporated into the epoxy matrix. Young’s modulus, ultimate tensile strength, strain at the fracture point, and the fracture toughness of nanocomposite samples were investigated. Besides, the tribological performance of these fabricated nanocomposites was evaluated and discussed. The results show that a significant change in the mechanical properties of the nanocomposites compared to the epoxy matrix. Also, the results reveal that the combination of NC with NGO improves the mechanical properties of graphene nanocomposites. It is found that adding NC to the NG/epoxy composite, may increase the fracture toughness up to 2 times as well as improve the ultimate tensile strength and strain at the fracture point. However, there was no significant change in Young’s modulus.
- 5 November 2021
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 16 (11) , e0259401
Open AccessEffect of nano clay, nano-graphene oxide and carbon nanotubes on the mechanical and tribological properties of crosslinked epoxy nanocomposite
The objective of this study is to investigate the effects of different nanoparticles as reinforcement in a polymeric matrix on the mechanical and tribological properties of the composite. The different particles including nanoclay (NC), nano-graphene oxide (NGO), and carbon nanotubes (CNT) with various weight percentages were incorporated into the epoxy matrix. Young’s modulus, ultimate tensile strength, strain at the fracture point, and the fracture toughness of nanocomposite samples were investigated. Besides, the tribological performance of these fabricated nanocomposites was evaluated and discussed. The results show that a significant change in the mechanical properties of the nanocomposites compared to the epoxy matrix. Also, the results reveal that the combination of NC with NGO improves the mechanical properties of graphene nanocomposites. It is found that adding NC to the NG/epoxy composite, may increase the fracture toughness up to 2 times as well as improve the ultimate tensile strength and strain at the fracture point. However, there was no significant change in Young’s modulus.
- 5 October 2021
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 28 (5) , 1626-1633
Modelling and Optimization of Surface Roughness and Specific Tool Wear in Milling Process
The present study has been carried out to optimize three machining parameters in the milling process to achieve minimum surface roughness and tool wear along with the maximum material removal rate. A specific tool wear factor has been...
- 5 October 2021
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 28 (5) , 1626-1633
Modelling and Optimization of Surface Roughness and Specific Tool Wear in Milling Process
The present study has been carried out to optimize three machining parameters in the milling process to achieve minimum surface roughness and tool wear along with the maximum material removal rate. A specific tool wear factor has been...
- 19 May 2021
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 73 (4) , 666-675
Design and fabrication of an online inductive sensor for identification of ferrous wear particles in engine oil
Purpose: The presence of ferrous wear debris in lubricating oil may cause progressive damage in the internal combustion engines. Online monitoring of the size and concentration of these particles in the oil is a way to optimize the engine performance and its life cycle. Design/methodology/approach: In this study, an online sensor was designed and fabricated to identify ferrous wear particles in the engine oil based on the induction method. The diameter of the sensor outlet duct was designed as small as possible to generate a high-intensity magnetic induction and achieve a proper sensitivity in the sensor. The experiments were designed and performed in offline mode. Furthermore, to evaluate the actual performance of the sensor in presence of iron particles in the oil, online tests were performed at different sizes and concentrations. Findings: It was concluded from offline tests that the highest sensitivity of the sensor occurs at the frequency and voltage of 2.5 kHz and 120 V, respectively. According to the results of the online tests, the larger the particle size, the higher the peaks at the sensor output. Also, a high density of the peaks was observed in the sensor output graphs as the concentration of particles was increased. Originality/value: The proposed sensor was able to identify ferrous wear particles larger than 125 µm separately, which is the failure limit in the internal combustion engines.
- 19 May 2021
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 73 (4) , 666-675
Design and fabrication of an online inductive sensor for identification of ferrous wear particles in engine oil
Purpose: The presence of ferrous wear debris in lubricating oil may cause progressive damage in the internal combustion engines. Online monitoring of the size and concentration of these particles in the oil is a way to optimize the engine performance and its life cycle. Design/methodology/approach: In this study, an online sensor was designed and fabricated to identify ferrous wear particles in the engine oil based on the induction method. The diameter of the sensor outlet duct was designed as small as possible to generate a high-intensity magnetic induction and achieve a proper sensitivity in the sensor. The experiments were designed and performed in offline mode. Furthermore, to evaluate the actual performance of the sensor in presence of iron particles in the oil, online tests were performed at different sizes and concentrations. Findings: It was concluded from offline tests that the highest sensitivity of the sensor occurs at the frequency and voltage of 2.5 kHz and 120 V, respectively. According to the results of the online tests, the larger the particle size, the higher the peaks at the sensor output. Also, a high density of the peaks was observed in the sensor output graphs as the concentration of particles was increased. Originality/value: The proposed sensor was able to identify ferrous wear particles larger than 125 µm separately, which is the failure limit in the internal combustion engines.
- 1 January 2019
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 37, 321-331
Effects of tool rake angle and tool nose radius on surface quality of ultraprecision diamond-turned porous silicon
- 1 January 2019
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 37, 321-331
Effects of tool rake angle and tool nose radius on surface quality of ultraprecision diamond-turned porous silicon
- 1 April 2018
- Published by Elsevier in Precision Engineering
- Vol. 52, 356-369
Material removal mechanism and surface integrity in ultraprecision cutting of porous titanium
- 1 April 2018
- Published by Elsevier in Precision Engineering
- Vol. 52, 356-369
Material removal mechanism and surface integrity in ultraprecision cutting of porous titanium
- 25 October 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 95 (1-4) , 479-492
Nanometer-scale chip formation and surface integrity of pure titanium in diamond turning
- 25 October 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 95 (1-4) , 479-492
Nanometer-scale chip formation and surface integrity of pure titanium in diamond turning