CPChulhyun Park

Chulhyun Park

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Chulhyun Park has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A 12-Bit 125-MS/s 2.5-Bit/Cycle SAR-Based Pipeline ADC Employing a Self-Biased Gain Boosting Amplifier

    by Chulhyun Park, Tao Chen, Kyoohyun Noh, Dadian Zhou, Suraj Prakash, Mohammadhossein Naderi Alizadeh, Aydin I. Karsilayan, Degang Chen, Randall L. Geiger, Jose Silva-Martinez

    This paper introduces a 12 bit 2.5 bit/cycle SAR-based pipeline ADC employing a self-bias gain boosting amplifier. The single-stage amplifier achieves a low-frequency gain of 37 dB, while consuming 1.3 mW of power consumption with 1.3 V of analog power supply. A 2.5 bit/cycle SAR ADC realizes as the sub-ADC in each stage, and reduces both power consumption and silicon area. A two-channel sampling architecture is employed to double the sampling rate and thereby maximize circuit efficiency. A digital calibration technique is used to reduce non-linearity and mismatches due to the RDAC, as well as gain error and offset of the open-loop residue amplifier. The prototype ADC was fabricated in TSMC 40-nm technology, and consumes 10.71 mW with 1.1 V / 1.3 V digital / analog power supplies. When operating at 125 MS/s, the ADC achieves an SFDR of 66.59 dB before calibration and 80.3 dB after calibration when measured at Nyquist frequency. The experimental results show a Walden FoM of 101 fJ/c.-s. before calibration and 47 fJ/c.-s. after calibration.


  • Open Access

    Joint Viterbi detection and decoding algorithm for bluetooth low energy systems

    by Chulhyun Park, Yongchul Jung, Jihoon Kim, Yunho Jung

    An efficient joint Viterbi detection and decoding (JVDD) algorithm for a bluetooth low energy (BLE) system is proposed. Since the convolutional coded Gaussian minimum‐shift keying (GMSK) signal is specified in the BLE 5.0 standard, two Viterbi processors are needed for detection and decoding. However, the proposed JVDD scheme uses only one Viterbi processor by modifying the branch metric with inter‐symbol interference information from GMSK modulation; therefore, the hardware complexity can be significantly reduced without performance degradation.


  • A 27.7 fJ/conv-step 500 MS/s 12-Bit Pipelined ADC Employing a Sub-ADC Forecasting Technique and Low-Power Class AB Slew Boosted Amplifiers

    by Mohammad H. Naderi, Chulhyun Park, Suraj Prakash, Martin Kinyua, Eric G. Soenen, Jose Silva-Martinez

    This paper presents a 12-bit 500 MS/s pipelined ADC fabricated in the 40 nm TSMC technology, which aims to reduce the power consumption associated with residue amplifiers and comparator cells. ADC architecture employs amplifiers with minimum transconductance requirements while considering the minimum unit capacitance value to maintain matching capacitor requirements for the target ADC specifications. The power efficient operational amplifiers are equipped with a Class C slew-rate boosting circuit that achieves a high slew-rate while static power is significantly saved. In addition, a forecasting technique in the sub-ADC is proposed, which reduces the number of active comparators during the sub-ADC’s conversion phase. The sign of the incoming signal is detected, and then the number of active comparators in each conversion cycle reduces by half, which leads to a more than 46% dynamic power savings from the sub-ADCs. The ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm 2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively.


  • A 13-Bit 260MS/s Power-Efficient Pipeline ADC Using a Current-Reuse Technique and Interstage Gain and Nonlinearity Errors Calibration

    by Dadian Zhou, Carlos Briseno-Vidrios, Junning Jiang, Chulhyun Park, Qiyuan Liu, Eric G. Soenen, Martin Kinyua, Jose Silva-Martinez

    A pipeline analog-to-digital converter (ADC) with high power efficiency is implemented in this paper. The ADC architecture consists of 3.5b, 3.5b, 3.5b, and 4b sub-ADCs. For the first three stages, a current-reuse technique is employed in the current mode multiplying digital-to-analog converters (MDACs). An operational transconductance amplifier (OTA) converts an input voltage into current; A current-steering DAC reuses the OTA bias current. The OTA and the DAC generate the sub-ADC residue in a current domain. As a result, both power consumption and thermal noise for the MDAC are reduced. A transimpedance amplifier (TIA) with a feedback resistor is utilized to convert the current signal to a voltage residue signal for the next stage. An off-chip calibration scheme is used to correct interstage gain and nonlinearity errors. The fabricated ADC achieves 68.1 dB signal-to-noise-and-distortion ratio (SNDR) and 82.3 dB spurious free dynamic range (SFDR) for a sinusoidal input at 4.17 MHz. The ADC operates at a maximum sampling frequency of 260 MHz. With an input signal at 123.129 MHz, the measured SNDR/SFDR are 66.3/78.22 dB, respectively. The total power consumption for the ADC running at maximum speed is 15.38 mW. Thus, the pipeline ADC achieves a 167.4 dB figure-of-merit (FoM). The chip was manufactured in a TSMC 40-nm CMOS process.


  • Effects of Electrical Characteristics on the Non-Rectangular Gate Structure Variations for the Multifinger MOSFETs

    by Chulhyun Park, Youngkyu Song, Jung Han Kang, Seong-Ook Jung, Ilgu Yun

    In this paper, modeling methodology of electrical characteristics for non-rectangular gate structured multifinger metal-oxide-semiconductor field-effect transistors based on minimum channel length is proposed. The test structures are fabricated and the parasitic model parameters are extracted using the measured data for the proposed model. The proposed model can support better physical explanation than the previously presented integrated length model. The proposed model can precisely explain the electrical characteristics and is supported by theoretical equations for non-rectangular gates, such as the threshold voltage, the saturation voltage, the saturation current, and the leakage current. However, the previous integrated length model cannot sufficiently explain the electrical characteristics for non-rectangular gates although it is sustained by theoretical equations. Furthermore, this paper shows the relationship between gate poly area and the electrical characteristics. As a result, the electrical characteristics are dependent on the variation of the minimum of the gate length, rather than the profile of gate length variation.


  • Effects of laser drilling through silicon substrate on MOSFET device characteristics

    by Youngkyu Song, Chulhyun Park, Junghan Kang, Ik-Bu Sohn, Young-Chul Noh, Jongmin Lee, Eung Jang Lee, Seung-Han Park, Soogil Lee, Jongill Hong, et al.

    The effects of laser drilling through silicon substrate formed by femtosecond laser on n-type MOSFET device characteristics are investigated. The tested MOSFET device structures are fabricated using the commercial 130-nm process. Through via holes and laser scanning line affect the device characteristics, such as drain current and threshold voltage, depending on the distance between the location of the drilling. The device degradation and variation along with a distance from the holes or the line are examined and the device characteristic variation is analyzed to determine the reliability of MOSFET devices against laser drilling damage.

  • Statistical modeling of layout-dependent characteristic fluctuations for multi-finger MOSFETs

    by Chulhyun Park, Junghan Kang, Seong-Ook Jung, Ilgu

    Large-signal models using extracted parasitic resistance are proposed for multi-finger MOSFETs and the statistical variations of parasitic resistances are investigated using statistical modeling. The extracted model parameters for the proposed models are verified with measured data. The models can explain the large-signal characteristics of multi-finger MOSFETs. Using the equivalent circuit model, the characteristic variations are statistically modeled with varying the gate layout factors and the extracted parasitic resistances. Based on the results, the gate geometry and extracted parasitic resistances. which are closely related to the source bias, can impact on the characteristic fluctuations of multi-finger MOSFETs.