Alessandro Pirondi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alessandro Pirondi has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Fabrizio Moroni
Università degli Studi di Parma
12 shared publications - Francesco Musiari
Department of Engineering for Industrial Systems and Technologies, University of Parma, Parco Area delle Scienze 181/A, 43121 Parma, Italy
7 shared publications F. Moroni
University of Parma
5 shared publications- Luca Collini
University of Parma
4 shared publications - Claudio Favi
Università degli Studi di Parma, Parma, Italy
3 shared publications - Davide Cocchi
Dipartimento di Ingegneria Industriale, Alma Mater Studiorum - Università di Bologna, Bologna, Italy
3 shared publications
Latest Publications
- 3 June 2026
- Published by Springer Nature
- p. 159-164
Additive-Manufactured Reinforcements for Composite-Metal Joints: A Life Cycle Engineering Approach
- 3 June 2026
- Published by Springer Nature
- p. 159-164
Additive-Manufactured Reinforcements for Composite-Metal Joints: A Life Cycle Engineering Approach
- Open Access
- 31 March 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 131 (1) , 24
Multiaxial Static and Fatigue Strength of LPBF-Manufactured AlSi10Mg in as-Built and T6 Conditions
Laser powder bed fusion (LPBF) technology has now reached a significant level of commercial maturity, offering some of the most reliable solutions in the additive manufacturing (AM) field. However, AM processes may introduce defects that result in high variability of mechanical properties and low reproducibility. This entails the need to thoroughly understand the behavior of the materials used, studying their response to the different types of stresses typical of real-world applications. The research activity presented consists of the analysis of the mechanical properties of the aluminum alloy AlSi10Mg, which is widely used due to its good strength-to-density ratio. Focus is put on the response to axial, torsional, and combined axial-torsional static and fatigue strength, comparing as-built T6 heat-treated conditions.
- 31 March 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 131 (1) , 24
Open AccessMultiaxial Static and Fatigue Strength of LPBF-Manufactured AlSi10Mg in as-Built and T6 Conditions
Laser powder bed fusion (LPBF) technology has now reached a significant level of commercial maturity, offering some of the most reliable solutions in the additive manufacturing (AM) field. However, AM processes may introduce defects that result in high variability of mechanical properties and low reproducibility. This entails the need to thoroughly understand the behavior of the materials used, studying their response to the different types of stresses typical of real-world applications. The research activity presented consists of the analysis of the mechanical properties of the aluminum alloy AlSi10Mg, which is widely used due to its good strength-to-density ratio. Focus is put on the response to axial, torsional, and combined axial-torsional static and fatigue strength, comparing as-built T6 heat-treated conditions.
- 2 April 2025
- Published by Springer Nature
- p. 429-439
A Knowledge-Based Approach for a CAD-Embedded Tool Preventing Hygienic Design Issues in Food Processing Machinery
- 2 April 2025
- Published by Springer Nature
- p. 429-439
A Knowledge-Based Approach for a CAD-Embedded Tool Preventing Hygienic Design Issues in Food Processing Machinery
- 3 March 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 239 (12) , 2282-2294
Mechanical characterization of innovative recyclable monomaterial films and laminates for food packaging
This work has been done within the RE.MO.PACK (REcyclable MOnomaterial PACKaging) project, that focuses on the development of innovative flexible packaging structures made from a single type of polymer, such as polyolefins, that can be effectively integrated into the recycling technologies used in the industry. The OTR (Oxygen Transmission Rate) and WVTR (Water Vapour Transmission Rate) performance (i.e., the so-called ‘barrier’ properties of the film) is ensured by vacuum deposition of aluminium oxides (AlO x ) and lacquering on the polymer film, while still being considered a mono-material under EU regulations. However, the success in the application of a polymeric film to seal a food tray or the shaping of a laminate into a primary packaging (i.e., in direct contact with food) are much dependent on its mechanical behaviour. Therefore, a part of the RE.MO.PACK project is dedicated to the mechanical characterisation of the different types of laminates developed within the project based on PE and with either AlOx or conventional aluminium metallization for water barrier. In particular, the following tests are performed: i) tensile testing according to the standard UNI-ISO 527-1,3 in machine (MD) and transverse (TD) directions; ii) AlO x coating adhesion through custom peel tests. The results show that the AlOx deposition do not affect the mechanical properties of the base film, and its adhesion is comparable with that of the conventional aluminium coating.
- 3 March 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 239 (12) , 2282-2294
Mechanical characterization of innovative recyclable monomaterial films and laminates for food packaging
This work has been done within the RE.MO.PACK (REcyclable MOnomaterial PACKaging) project, that focuses on the development of innovative flexible packaging structures made from a single type of polymer, such as polyolefins, that can be effectively integrated into the recycling technologies used in the industry. The OTR (Oxygen Transmission Rate) and WVTR (Water Vapour Transmission Rate) performance (i.e., the so-called ‘barrier’ properties of the film) is ensured by vacuum deposition of aluminium oxides (AlO x ) and lacquering on the polymer film, while still being considered a mono-material under EU regulations. However, the success in the application of a polymeric film to seal a food tray or the shaping of a laminate into a primary packaging (i.e., in direct contact with food) are much dependent on its mechanical behaviour. Therefore, a part of the RE.MO.PACK project is dedicated to the mechanical characterisation of the different types of laminates developed within the project based on PE and with either AlOx or conventional aluminium metallization for water barrier. In particular, the following tests are performed: i) tensile testing according to the standard UNI-ISO 527-1,3 in machine (MD) and transverse (TD) directions; ii) AlO x coating adhesion through custom peel tests. The results show that the AlOx deposition do not affect the mechanical properties of the base film, and its adhesion is comparable with that of the conventional aluminium coating.
- 31 May 2024
- Published by Elsevier in Composites Science and Technology
- Vol. 255
Assessment of the effect of embedded RFID tag on a composite laminate strength
- 31 May 2024
- Published by Elsevier in Composites Science and Technology
- Vol. 255
Assessment of the effect of embedded RFID tag on a composite laminate strength
- Open Access
- 14 December 2023
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 129
Influence of high frequency on the fatigue life of metallic single lap joints
- 14 December 2023
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 129
Open AccessInfluence of high frequency on the fatigue life of metallic single lap joints
- 24 November 2023
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (1) , 115-143
Metal-metal and metal-composite joints with 3D printed aluminium substrates: effect of surface treatment on the mode I fracture toughness
- 24 November 2023
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 101 (1) , 115-143
Metal-metal and metal-composite joints with 3D printed aluminium substrates: effect of surface treatment on the mode I fracture toughness
- Open Access
- 7 October 2023
- Published by Elsevier in Journal of Food Engineering
- Vol. 363
Towards computer-aided hygienic design: Definition of a knowledge-based system for food processing equipment
- 7 October 2023
- Published by Elsevier in Journal of Food Engineering
- Vol. 363
Open AccessTowards computer-aided hygienic design: Definition of a knowledge-based system for food processing equipment