Giuseppe Francesco Nallo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Giuseppe Francesco Nallo has a total of 66 co-authors. Here are the top co-authors by number of shared publications:
- Fabio Subba
Politecnico di Torino
6 shared publications - Roberto Zanino
Politecnico di Torino
5 shared publications - Laura Savoldi
Politecnico di Torino
3 shared publications R. Zanino
Politecn Torino, Dipartimento Energia, NEMO Grp, Corso Duca Abruzzi 24, I-10129 Turin, Italy
3 shared publicationsAntonino Lombardo
2 shared publicationsG. Mazzitelli
Fusion and Technologies for Nuclear Safety Department, ENEA, C.R. Frascati, C.P. 65-00044 Frascati, Rome, Italy
2 shared publications
Latest Publications
- Open Access
- 27 April 2026
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 58 (9)
Benchmark of system thermal-hydraulic codes for the test section of the dip cooler instability test facility
- 27 April 2026
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 58 (9)
Open AccessBenchmark of system thermal-hydraulic codes for the test section of the dip cooler instability test facility
- Open Access
- 8 April 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 47
Analysis of H-mode and L-mode plasmas with a liquid Sn CPS divertor test unit in the ASDEX Upgrade tungsten divertor
- 8 April 2026
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 47
Open AccessAnalysis of H-mode and L-mode plasmas with a liquid Sn CPS divertor test unit in the ASDEX Upgrade tungsten divertor
- 26 September 2024
- Published by Taylor & Francis in Nuclear Technology
- Vol. 211 (10) , 2490-2507
Development of a New Thermal-Hydraulic Module for FRENETIC, a Code for the Multiphysics Analysis of Liquid Metal–Cooled Reactors
- 26 September 2024
- Published by Taylor & Francis in Nuclear Technology
- Vol. 211 (10) , 2490-2507
Development of a New Thermal-Hydraulic Module for FRENETIC, a Code for the Multiphysics Analysis of Liquid Metal–Cooled Reactors
- Open Access
- 24 July 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 428
Development and preliminary validation of TIFONE, a design-oriented code for the inter-wrapper flow and heat transfer in liquid-metal-cooled reactors
- 24 July 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 428
Open AccessDevelopment and preliminary validation of TIFONE, a design-oriented code for the inter-wrapper flow and heat transfer in liquid-metal-cooled reactors
- Open Access
- 23 August 2023
- Published by Springer Nature in Journal of Fusion Energy
- Vol. 42 (2) , 1-8
Towards Integrated Target–SOL–Core Plasma Simulations for Fusion Devices with Liquid Metal Targets
Self-healing liquid metal divertors (LMDs) based on the Capillary Porous Structure (CPS) concept are currently being considered among the possible solutions to the power exhaust problem in future fusion reactors. Indeed, the passive replenishment of the plasma-facing surface by capillary forces and the self-shielding of the target via vapor emission can potentially improve the divertor lifetime and its resilience to transient loads. On the other hand, the LMD target erosion can be significant due to evaporation and thermal sputtering, on top of physical sputtering, possibly leading to unacceptable core plasma dilution/power losses (for a low-Z/high-Z metal such as Li and Sn, respectively). For this reason, it is necessary to assess whether an LMD is compatible with an European DEMO (EU-DEMO) plasma scenario. This requires a self-consistent model of the impurity emission from the target, the plasma in both the scrape-off layer (SOL) and the core regions and the transport of impurities therein. In this paper, an an integrated modelling approach is proposed, which is based on SOLPS-ITER and includes its coupling with a target erosion model written in FreeFem++ and a core plasma model (ASTRA/STRAHL). An application of the coupled SOL-target model to simulate experiments performed in the Magnum-PSI linear plasma device with a CPS target filled with Li is also included to provide a first demonstration of the capabilities of the approach. Results are promising, being in good agreement (within a few degrees) with the measured target temperature distribution. In perspective, the modelling framework presented here will be applied to the EU-DEMO with an Sn divertor.
- 23 August 2023
- Published by Springer Nature in Journal of Fusion Energy
- Vol. 42 (2) , 1-8
Open AccessTowards Integrated Target–SOL–Core Plasma Simulations for Fusion Devices with Liquid Metal Targets
Self-healing liquid metal divertors (LMDs) based on the Capillary Porous Structure (CPS) concept are currently being considered among the possible solutions to the power exhaust problem in future fusion reactors. Indeed, the passive replenishment of the plasma-facing surface by capillary forces and the self-shielding of the target via vapor emission can potentially improve the divertor lifetime and its resilience to transient loads. On the other hand, the LMD target erosion can be significant due to evaporation and thermal sputtering, on top of physical sputtering, possibly leading to unacceptable core plasma dilution/power losses (for a low-Z/high-Z metal such as Li and Sn, respectively). For this reason, it is necessary to assess whether an LMD is compatible with an European DEMO (EU-DEMO) plasma scenario. This requires a self-consistent model of the impurity emission from the target, the plasma in both the scrape-off layer (SOL) and the core regions and the transport of impurities therein. In this paper, an an integrated modelling approach is proposed, which is based on SOLPS-ITER and includes its coupling with a target erosion model written in FreeFem++ and a core plasma model (ASTRA/STRAHL). An application of the coupled SOL-target model to simulate experiments performed in the Magnum-PSI linear plasma device with a CPS target filled with Li is also included to provide a first demonstration of the capabilities of the approach. Results are promising, being in good agreement (within a few degrees) with the measured target temperature distribution. In perspective, the modelling framework presented here will be applied to the EU-DEMO with an Sn divertor.
- 1 March 2022
- Published by IOP Publishing in Nuclear Fusion
- Vol. 62 (3) , 036008
SOLPS-ITER simulations of a CPS-based liquid metal divertor for the EU DEMO: Li vs Sn
In this work, we study the effect of installing a liquid metal divertor (LMD) using a capillary-porous structure in the EU DEMO tokamak within the same envelope of the baseline solid divertor. We used the SOLPS-ITER code to model the scrape-off layer (SOL) plasma and neutrals, coupled to a target thermal model to enable the self-consistent calculation of the LM target erosion rate, and adopting a fluid neutral model for the sake of simplicity. First calculations considering only D and Li (or Sn) showed a significant reduction of the steady state target heat load with respect to simulations considering only D, thanks to vapor shielding. Nevertheless, the computed peak target heat flux (∼31 MW m−2 and ∼44 MW m−2 for Li and Sn, respectively) was still larger than/borderline to the power handling limit of the LMD concepts considered. Moreover, the impurity concentration in the pedestal—a proxy for the core plasma dilution/contamination—was computed to be above/close to tolerability limits suggested by previous COREDIV calculations. These results indicate that the operational window of an LMD for the EU DEMO, without any additional impurity seeding, might be too narrow, if it exists, and that Sn looks more promising than Li. A second set of calculations was then performed simulating Ar seeding in the SOL, to further reduce the target heat load, and consequently the metal erosion rate. It was found that the mitigation of the plasma heat load due to Ar radiation in the SOL effectively replaces the radiation associated to vapor shielding in front of the target, thus allowing to operate the LMD in a regime of low target erosion. The resulting operational window was found to be significantly wider, both in terms of tolerable peak target heat flux and of acceptable core plasma contamination.
- 1 March 2022
- Published by IOP Publishing in Nuclear Fusion
- Vol. 62 (3) , 036008
SOLPS-ITER simulations of a CPS-based liquid metal divertor for the EU DEMO: Li vs Sn
In this work, we study the effect of installing a liquid metal divertor (LMD) using a capillary-porous structure in the EU DEMO tokamak within the same envelope of the baseline solid divertor. We used the SOLPS-ITER code to model the scrape-off layer (SOL) plasma and neutrals, coupled to a target thermal model to enable the self-consistent calculation of the LM target erosion rate, and adopting a fluid neutral model for the sake of simplicity. First calculations considering only D and Li (or Sn) showed a significant reduction of the steady state target heat load with respect to simulations considering only D, thanks to vapor shielding. Nevertheless, the computed peak target heat flux (∼31 MW m−2 and ∼44 MW m−2 for Li and Sn, respectively) was still larger than/borderline to the power handling limit of the LMD concepts considered. Moreover, the impurity concentration in the pedestal—a proxy for the core plasma dilution/contamination—was computed to be above/close to tolerability limits suggested by previous COREDIV calculations. These results indicate that the operational window of an LMD for the EU DEMO, without any additional impurity seeding, might be too narrow, if it exists, and that Sn looks more promising than Li. A second set of calculations was then performed simulating Ar seeding in the SOL, to further reduce the target heat load, and consequently the metal erosion rate. It was found that the mitigation of the plasma heat load due to Ar radiation in the SOL effectively replaces the radiation associated to vapor shielding in front of the target, thus allowing to operate the LMD in a regime of low target erosion. The resulting operational window was found to be significantly wider, both in terms of tolerable peak target heat flux and of acceptable core plasma contamination.
- 15 February 2022
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 78 (3) , 186-198
Identification of the Postulated Initiating Events of Accidents of a CPS-Based Liquid Metal Divertor for the EU DEMO Fusion Reactor
A preliminary but systematic safety analysis of a liquid metal divertor (LMD) for the EU DEMO performed by means of the Functional Failure Mode and Effect Analysis (FFMEA) is presented. This methodology is suitable for the analysis of the LMD, which is undergoing preconceptual design. In fact, the FFMEA compensates for the lack of detailed design information by postulating the loss of a system function, rather than a specific component failure. The implementation of the FFMEA led to a better understanding of the safety and operational issues associated with the system and to the identification of a list of postulated initiating events (PIEs), i.e., the most challenging conditions for the plant. The PIEs, together with their possible consequences, represent an input for future quantitative safety analyses. Due to the early design stage of the LMD and the iterative nature of the methodology, this list will evolve alongside the design detail and with improvements in the understanding of phenomena driving reactor behavior. The study highlighted some safety-relevant issues, e.g., those related to materials compatibility and system modularity, to be addressed in the perspective of a safety-driven design evolution.
- 15 February 2022
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 78 (3) , 186-198
Identification of the Postulated Initiating Events of Accidents of a CPS-Based Liquid Metal Divertor for the EU DEMO Fusion Reactor
A preliminary but systematic safety analysis of a liquid metal divertor (LMD) for the EU DEMO performed by means of the Functional Failure Mode and Effect Analysis (FFMEA) is presented. This methodology is suitable for the analysis of the LMD, which is undergoing preconceptual design. In fact, the FFMEA compensates for the lack of detailed design information by postulating the loss of a system function, rather than a specific component failure. The implementation of the FFMEA led to a better understanding of the safety and operational issues associated with the system and to the identification of a list of postulated initiating events (PIEs), i.e., the most challenging conditions for the plant. The PIEs, together with their possible consequences, represent an input for future quantitative safety analyses. Due to the early design stage of the LMD and the iterative nature of the methodology, this list will evolve alongside the design detail and with improvements in the understanding of phenomena driving reactor behavior. The study highlighted some safety-relevant issues, e.g., those related to materials compatibility and system modularity, to be addressed in the perspective of a safety-driven design evolution.
- 1 November 2021
- Published by Elsevier in Fusion Engineering and Design
- Vol. 172
Parametric study of the radiative load distribution on the EU-DEMO first wall due to SPI-mitigated disruptions
- 1 November 2021
- Published by Elsevier in Fusion Engineering and Design
- Vol. 172
Parametric study of the radiative load distribution on the EU-DEMO first wall due to SPI-mitigated disruptions