LKLeonid Kolomiets

Leonid Kolomiets

*This is an algorithmically generated author record based on publicly available information.

Leonid Kolomiets has a total of 145 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    COMPREHENSIVE ASSESSMENT OF TWO-PHASE FLOW DURING REFRIGERANT BOILING INSIDE PROFILED HORIZONTAL TUBES

    by V.V. Gorin, L.V. Kolomiets, Ya.E. Trokoz

    This paper presents an evaluation of research results on hydrodynamics and heat transfer during the boiling of refrigerant R22 inside a heat exchange tube with internal longitudinal fins, based on models and correlations proposed by various authors in the available literature. The models demonstrate different approaches to representing correlations for heat transfer calculations, taking into account the influence of hydrodynamic forces such as surface tension, viscosity, and inertia, which affect the motion of two-phase flow in tubes and channels and contribute to the understanding of physical phenomena. The study describes the experimental setup, where heat transfer during refrigerant boiling was investigated under the following operating parameters: heat flux density q = 5, 10, and 20 kW/(m2⋅K), mass flux G = 70, 110, and 200 kg/(m2⋅s), local vapor quality x = 0.01–0.64, and refrigerant saturation temperature ts=15 °C. The influence of heat flux, mass flux, and vapor quality on heat transfer was analyzed, providing valuable insights into heat transfer processes during two-phase refrigerant boiling in tubes and channels. A manufacturing technique for longitudinal fins and unique mandrels for drawing inside copper tubes was developed. Flow visualization revealed stratified, wavy, wavy-slugs, and annular flow regimes. Verification of two-phase flow regimes was performed by comparing experimental results with calculations based on corresponding dependencies from existing flow regime maps. Experimental data were processed using an appropriate methodology for calculating heat transfer coefficients. Based on the obtained results, heat transfer during boiling of two-phase R22 flow inside the finned tube was calculated using 14 models and correlations. The analysis identified models and correlations that most accurately describe the experimental results and can be recommended for engineering practice. Bibl. 31, Tab. 4, Fig. 4.

  • Open Access

    DEVELOPMENT AND RESEARCH OF METHODS FOR AUTOMATION OF MEASURING PROCESSES AT AUTOMATIC STATIONS

    by L. V. Kolomiets, T.I. Pokhlebina, V.F. Kuznetsov, L.V. Kuznetsova

    The article substantiates the relevance of studying modern measuring systems used for monitoring petroleum products at fuel filling stations (FFSs). It is shown that FFS networks constitute an essential component of the petroleum product supply infrastructure; therefore, improving the efficiency of their operation is of considerable practical importance. Reliable measurement of fuel quantity during receipt, storage, and dispensing is a key prerequisite for accurate inventory accounting, reduction of product losses, and compliance with current metrological and regulatory requirements. Modern information and measurement systems installed at fuel filling stations are designed for continuous monitoring of fuel inventory in storage tanks. Such systems integrate level gauges, sensors, and control units to automatically determine fuel level, volume, density, and temperature, as well as to record changes in fuel inventory in real time. The implementation of automated measuring systems significantly improves the accuracy and reliability of measurements, reduces the influence of the human factor, enhances inventory management, and increases the operational efficiency of fuel filling stations. A comparative analysis of the equipment used at fuel filling stations in the southern region of Ukraine was carried out. It was established that ultrasonic and magnetostrictive level gauges are the most widely used instruments for monitoring fuel receipt, storage, and dispensing. These devices differ in their operating principles, metrological performance, functional capabilities, and operating conditions. Based on the comparative analysis of their technical and metrological characteristics, recommendations are proposed for selecting level gauges according to measurement accuracy requirements, operating conditions, and regional climatic features. The proposed recommendations can be applied to improve the metrological support of fuel filling stations, increase the reliability of fuel accounting, and enhance the efficiency of modern information and measurement systems. У статті обґрунтовано актуальність дослідження сучасних засобів вимірювальної техніки, що застосовуються для контролю параметрів нафтопродуктів на автозаправних станціях. Проведено порівняльний аналіз технічних і метрологічних характеристик ультразвукових та магнітострикційних рівнемірів, які використовуються на АЗС південного регіону України. Визначено їх переваги, обмеження та особливості експлуатації. Розроблено рекомендації щодо вибору рівнемірів залежно від умов експлуатації, вимог до точності вимірювань і кліматичних особливостей регіону. Запропоновані рекомендації спрямовані на підвищення достовірності обліку нафтопродуктів, удосконалення метрологічного забезпечення АЗС та підвищення ефективності їх функціонування.

  • DIAGNOSTICS OF STRESSES AND DEFORMATIONS IN ELASTIC ELEMENTS OF FORCE METERS

    by L. Kolomiets, O. Lymarenko, A. Perederko, A. Tomkevych, S. Bieletskyi

    The article demonstrates that, when measuring forces using weighing devices under long-term dynamic loading, particular importance is attached to maintaining the metrological parameters of resistive strain force sensors over a specified time interval. The study of elastic elements with different geometries presents significant mathematical difficulties in solving the corresponding problems of elasticity theory. In addition, accounting for the dynamic components of external loads acting on the elastic element considerably complicates the derivation of closed-form solutions. An analysis of previous studies and relevant publications has shown that the finite element method (FEM), one of the most well-developed and effective methods for structural analysis, is an appropriate approach for determining the stress–strain state of elastic elements. The method is implemented in the ANSYS finite element analysis software and makes it possible to analyze and design force sensors under a wide range of loading conditions. A promising design of a resistive strain force sensor has been developed. The sensor incorporates an analog-to-digital converter (ADC) with temperature and position sensing functions. Two blind holes are provided in the central part of the elastic element, in which resistive strain gauges are mounted as close as possible to the axis of symmetry of the elastic element, corresponding to the zone of maximum strain. The strain gauges are protected from mechanical damage by two covers installed on the outer surface of the sensor. Positioning the resistive strain gauges as close as possible to the axis of symmetry of the elastic element makes it possible to reduce the influence of adverse factors on the accuracy and stability of measurement results. У статті показано, що під час вимірювання сил ваговимірювальними приладами в умовах тривалих динамічних навантажень особливого значення набуває збереження метрологічних параметрів резистивних тензодатчиків сили протягом певного часового інтервалу. Дослідження пружних елементів різної форми супроводжується значними математичними труднощами під час розв’язання відповідних задач теорії пружності. Врахування динамічних складових зовнішніх впливів на пружний елемент також суттєво ускладнює отримання їх аналітичного розв’язання. Аналіз результатів досліджень і відомих публікацій показав, що для визначення напружено-деформованого стану пружних елементів доцільним є застосування одного з найбільш розвинених та ефективних методів розрахунку конструкцій - методу скінченних елементів, реалізованого в ANSYS. Розроблено перспективну конструкцію резистивного тензометричного датчика сили, яка містить аналого-цифровий перетворювач із функціями вимірювання температури та визначення положення. У центральній частині пружного елемента датчика сили виконано два глухі отвори, всередині яких встановлено резистивні тензодатчики в безпосередній близькості до осі симетрії пружного елемента, що відповідає зоні максимальних деформацій.

  • Open Access

    RESEARCH OF THE ACCURACY AND RELIABILITY OF LOAD LIMITERS FOR CRANES

    by L. Kolomiets, O. Lymarenko, A. Tomkevych, V. Tiupa, M. Matviichuk, H. Oliash

    It is shown that the increase in productivity, reliability and safety of operation of a truck crane largely depends on the use of safety devices, in particular load limiters. A method for monitoring the safe operation of a truck crane has been developed, which involves the use of sensors for load capacity, hook lifting height, boom angle and length, as well as stress-strain state meters located in the "critical" zones of the crane metal structure, where maximum stresses and displacements occur that can cause damage or destruction of structural elements. A full-scale experiment was conducted, the results of which determined the actual stress-strain state of individual elements of the metal structure of a truck crane. Experimental data obtained using primary measuring transducers made it possible to assess the real nature of the distribution of loads and deformations of the metal structure of a truck crane under operating conditions. Mathematical models of the elements of the supporting system of a truck crane were built and their software implementation was performed using the ANSYS and MATLAB software packages. The results of calculations for six calculation cases showed that the values of stresses and deformations do not exceed the permissible values and are consistent with the results of full-scale experimental studies. The design of a safety device with a transmission mechanism for controlling the tension force of a truck crane cargo rope was studied. It was established that placing the safety device at the point of attachment of the rope makes it possible to reduce the error in measuring its tension force, caused by friction losses in the block bearings and the rigidity of the rope during its bending. The results of the studies confirm the feasibility of using the proposed method of controlling the stress-strain state and design solutions of safety devices to improve the safety of operation of truck cranes. The combination of computational modeling with the results of field measurements makes it possible to timely identify critical areas of a metal structure and increase the reliability of monitoring its technical condition. Показано, що підвищення надійності та безпеки експлуатації кранаів значною мірою залежить від застосування обмежувачів вантажопідіймальності та обґрунтованого вибору місця їх розміщення на металоконструкції. Розроблено спосіб контролю безпечної роботи автомобільного крана із застосуванням датчиків вантажопідйомності, висоти підйому гака, кута та довжини стріли, а також вимірювачів напружено-деформованого стану елементів металоконструкції. Експериментально визначено фактичний напружено-деформований стан металоконструкції крана. Побудовані математичні моделі та проведені розрахунки в програмних комплексах ANSYS і MATLAB підтвердили, що напруження і деформації не перевищують допустимих значень та узгоджуються з результатами натурних досліджень. Досліджено конструкцію обмежувачів вантажопідіймальності для контролю зусилля натягу вантажного каната крана.

  • Open Access

    ANALYSIS OF METROLOGICAL SUPPORT FOR FUEL FILLING STATIONS DURING PERIODIC VERIFICATION OF LEVEL GAUGES (OVERVIEW)

    by L. Kolomiets, V. Kuznetsov, L. Kuznetsova

    The article examines current challenges in the metrological support of fuel filling stations (FFSs) and identifies the main directions for improving measurement reliability and operational efficiency. It is shown that metrological support represents a comprehensive system of scientific, organizational, and technical measures aimed at ensuring the uniformity, accuracy, reliability, and traceability of measurements throughout fuel storage and dispensing processes. Particular attention is paid to the automated monitoring of fuel parameters in storage tanks using ultrasonic and magnetostrictive level gauges operating in real time. These information and measurement systems continuously determine fuel level, volume, density, and temperature, prevent unauthorized fuel losses, improve inventory control, and ensure compliance with current regulatory and metrological requirements. The study demonstrates that compliance with metrological regulations and technical standards is an essential prerequisite for the safe, reliable, and economically efficient operation of fuel filling stations. The accuracy of level gauges directly affects the financial security of fuel retail enterprises by minimizing losses during storage and distribution, preventing inventory discrepancies, and ensuring transparent accounting of petroleum products. Reliable measurements enable operators to compare the quantity of fuel delivered by tank trucks with the amount actually dispensed through fuel dispensers. Even minor measurement errors may lead to significant financial losses, particularly for large fuel distribution networks. Therefore, reducing measurement uncertainty requires the implementation of modern automated information and measurement systems together with regular verification of measuring instruments and continuous metrological supervision. The analysis of the current state of metrological support revealed several significant problems, including a shortage of qualified personnel, insufficient availability of modern equipment for the verification of level gauges, the continued use of outdated measurement methods, and the inadequate condition of the national metrological reference infrastructure. These shortcomings limit the effective implementation of advanced information and measurement systems and reduce the reliability of measurement results. The paper concludes that modernization of metrological infrastructure, improvement of verification procedures, updating of the regulatory framework, and continuous professional training of specialists are essential for enhancing the accuracy, traceability, and reliability of measurements at fuel filling stations. У статті розглянуті проблеми метрологічного забезпечення та наведено можливі шляхи рішення. Метрологічне забезпечення на АЗС містить наукові, організаційні та технічні засоби для точних вимірювань. Актуальною є організація контролю палива у резервуарах, яка здійснюється онлайн через ультрозвукові або магнітострикційні рівнеміри. Вони фіксують обсяг, густину і температуру палива, запобігають зливам та забезпечують облік згідно нормативам. Показано, що виконання вимог нормативних документів є критично важливим для безпеки різних виробничих процесів, їх ефективності. Аналіз стану метрологічного забезпечення виявив такі проблеми, як відсутність кваліфікованих кадрів, відсутність сучасного вимірювального обладнання для повірки рівнемірів та використання застарілих методів вимірювань, при великому асортименті пропонованих на ринку сучасних імпортних засобів вимірювань, а саме ІВС, та невідповідний стан еталонної бази.

  • Open Access

    RESEARCH OF METROLOGICAL CHARACTERISTICS OF HANGING SAFETY AND WEIGHING DEVICES

    by L. V. Kolomiets, A. L. Perederko, O. V. Banzak, H. D. Bratchenko, H. I. Oliash, Г. І. Оляш

    The article shows that in the complex mechanization and automation of production processes, the elimination of heavy manual labor when performing basic and auxiliary production operations, a large role is assigned to highly productive, reliable and safe-to-operate lifting machines. Increasing the productivity, reliability and safety of lifting machines in many cases depend on the safety and weighing devices used in them. The most effective and rational installation locations for safety devices and scales on lifting machines have been analyzed. We established that the rational installation of scales on the hook and in the hook suspension is. The article describes safety and weighing devices that implement this mounting option. It is shown that the most promising direction for creating safety devices is the development of combined devices that contain force-measuring devices along with the mechanical basis; the possibility of placing all equipment, except for force-measuring sensors, in the crane operator's cab or on the console; and ease of integration into the design of signaling devices. The authors' studies show that for mounted devices, random measurement errors are characteristic, caused by skew in the lifting-lowering load process due to the random nature of friction forces in the hoist system blocks. To reduce the specified error, the authors conducted studies that enabled the creation of crane electronic strain gauge scales with a load capacity of 20 to 200 kN, designed for weighing loads transported by cranes. The scales have individual battery power sources and an indication of the load mass on a light board. The results of experimental and field tests showed that the relative error and variation of measurement readings of these devices under static weighing conditions did not exceed 0.06 % of the measured value, which is within the permissible errors of the scales. У статті показано,що в комплексній механізації та автоматизації виробничих процесів, виключенні важкої ручної праці при виконанні основних і допоміжних виробничих операцій велика роль відводиться високопродуктивним, надійним та безпечним в експлуатації вантажопідіймальним машинам. Підвищення продуктивності, надійності та безпеки їх роботи суттєво залежить від застосовуваних в них запобіжних і зважуючих пристроїв. Проведено аналіз найбільш ефективних та раціональних місць установки вказаних пристроїв на вантажопідіймальних машинах, чим встановлено, що раціональною є установка пристоїв на гаку та в гаковій підвісці. Наведено опис запобіжних та зважуючих пристроїв, які реалізують цей варіант установки. Проведені дослідження показують, що найбільш істотною похибкою таких пристроїв є похибка, що виникає через тертя у напрямних хвостовика гака, яка зменшується зі збільшенням ККД блоків поліспасту.

  • Open Access

    MODERN GRAVIMETERS OF AVIATION GRAVIMETRIC SYSTEM

    by О. М. Безвесільна, L. V. Kolomiets, T. O. Tolochko

    Information about the Earth's gravitational field is used in seismology (earthquake forecasting), aviation and space technology (correction of inertial navigation systems of rockets, airplanes, orbits of spacecraft), for the study of geodynamic phenomena, the implementation of tasks in engineering geology, archeology, cartography, etc. The feasibility of using AGS for gravimetric measurements and obtaining information about the Earth's gravitational field is substantiated. The analysis of currently existing gravimeters of aviation gravimetric systems is carried out, their main shortcomings are identified: low measurement accuracy (3-10 mGal); the mandatory need to apply the procedure for filtering the output signal of the AGS gravimeter; instability of the static transfer coefficient of the AGS gravimeter, caused by changes in the properties of structural elements; low speed. Modern promising developments (gyroscopic, ballistic, piezoelectric, capacitive, string gravimeters) in the field of creating new-type aviation gravimeters with higher accuracy (1-2 mGal) and speed than known ones, as a result of choosing the natural frequency of the gravimeter at the intersection point of the spectral densities of the useful PST signal and the main interference of vertical acceleration, are considered. This frequency is 0.1 s–1. Then the gravimeter performs the functions of a filter of the main disturbing vibration accelerations, the frequency of which exceeds 0.1 s–1. It is proposed to use a two-channel (differential) method of measuring PST in all gravimeter designs. Then the useful signal is doubled by 2g, and the signals of the main disturbing vertical acceleration, instrumental errors from the influence of changes in temperature, pressure and other factors of the external environment are canceled. Інформацію про гравітаційне поле Землі використовують у сейсмології (прогноз землетрусів), авіаційній і космічній техніці (корекція систем інерціальної навігації ракет, літаків, орбіт космічних літальних апаратів), для дослідження геодинамічних явищ, реалізації завдань інженерної геології, археології, картографії тощо. Обґрунтовано доцільність використання авіаційних гравіметричних систем для проведення гравіметричних вимірювань та отримання інформації про гравітаційне поле Землі. Проведено аналіз відомих нині гравіметрів авіаційних гравіметричних систем, визначено їх переваги та недоліки. Розглянуто сучасні перспективні розробки у галузі конструювання авіаційних гравіметрів нового типу з високою точністю та швидкодією порівняно з відомими.

  • Open Access

    ECOMANAGEMENT AS A TOOL FOR IMPROVING THE SAFETY OF FILLING STATIONS

    by State University of Intelligent Technology and Communications, L. Kolomiets, T. Pokhlebina, V. Kuznetsov, L. Kuznetsova

    The presented article analyzes the main environmental impacts that arise during the operation of gas stations. An assessment of the environmental risks that occur during the operation of gas stations is given. The need to develop and implement an environmental management system for gas stations is considered, which will allow the enterprise to limit negative impacts on the environment, reduce losses of petroleum products, and reduce waste volumes. Based on the fact that many companies have already implemented quality management systems, the authors propose to take these systems as a basis and supplement them with the necessary components of the environmental management system. It is shown that to prevent the occurrence of environmentally unsafe situations during the operation of gas stations, it is necessary to: equip underground fuel tanks with double walls, equipped with automated devices for controlling the leakage of petroleum products; equip facilities for cleaning surface rainwater accidentally contaminated with petroleum products; to strengthen the requirements for oil product vapor capture systems in the direction of introducing waste-free technologies; to introduce additional stages of wastewater treatment of auto-washing stations; to periodically carry out preventive cleaning of soils in areas adjacent to stations from oil products, using special preparations; to conduct a periodic assessment of man-made and environmental risks caused by objective and subjective factors of the stations’ activities; to introduce a mandatory monitoring system within the scope of influence of gas stations and ensure the implementation of the plan for mandatory periodic technical diagnostics of station equipment. У статті проаналізовані основні екологічні впливи, які виникають при експлуатації автозаправних станцій (АЗС). Надана оцінка екологічним ризикам, що мають місце при експлуатації АЗС. Розглянута необхідність розробки та впровадження системи екологічного менеджменту для АЗС, що дасть можливість підприємству обмежити негативні впливи на навколишнє середовище, скоротити втрати нафтопродуктів, знизити об’єми відходів. Враховуючи те, що на багатьох об’єктах напівстаціонарної роздрібної торгівлі з продажу пального для автотранспортних засобів з використанням спеціального обладнання запроваджені системи управління якістю (СУЯ), авторами запропоновано взяти елементи цих систем за основу та доповнити необхідними компонентами системи екологічного менеджменту.

  • Open Access

    IMPLEMENTATION OF THE ISO 37001:2025 STANDARD AS A TOOL FOR PREVENTING CORRUPTION IN THE HIGHER EDUCATION SYSTEM

    by State University of Intelligent Technology and Communications, L. V. Kolomiets

    Corruption as an anti-social factor creates significant difficulties on the path to the formation and development of legal statehood, as it contributes to the destruction of the most important values guaranteed to us by the Basic Law of Ukraine - the Constitution. The article analyzes the corruption risks of educational entities and central executive bodies that ensure the formation and implementation of state policy in the fields of education and science. Based on the research conducted, it is shown that the International Organization for Standardization (ISO) creates universal tools for management, including in the field of combating corruption, which allow organizations to implement sustainable and controllable management systems in accordance with the best international practices. The paper considers the possibilities of applying the international standard ISO 37001:2025 "Anti-corruption management systems" in higher education institutions. The key elements of the standard, its adaptation to the educational environment and the potential for increasing the transparency and accountability of management processes are analyzed. Recommendations are given for the integration of anti-corruption mechanisms into the internal control system of higher education institutions. A Priority Action Plan for the implementation of the international standard ISO 37001 in educational institutions, adapted to the university environment, has been proposed. A training module plan for the ISO 37001 standard for employees of higher education institutions is proposed, which includes four main modules: Module 1. Introduction to anti-corruption management; Module 2. Basic requirements of ISO 37001; Module 3. Practical application; Module 4. Responsibility and consequences. Examples of the transformation of ISO 37001:2025 into draft educational standards (national level or internal university standard) are provided. У статті проведено аналіз корупційних ризиків суб’єктів освітньої діяльності та центральних органів виконавчої влади, що забезпечують формування та реалізацію державної політики у сферах освіти і науки. На підставі проведених досліджень показано, що Міжнародна організація зі стандартизації (ISO) створює універсальні інструменти для управління, у тому числі у сфері протидії корупції, які дозволяють організаціям впроваджувати стійкі та контрольовані системи управління відповідно до кращих світових практик. В роботі розглядаються можливості застосування міжнародного стандарту ISO 37001:2025 «Системи менеджменту протидії корупції» в установах вищої освіти. Аналізуються ключові елементи стандарту, його адаптація до освітнього середовища та потенціал у підвищенні транспарентності та підзвітності управлінських процесів. Подано рекомендації щодо інтеграції антикорупційних механізмів у систему внутрішнього контролю закладів вищої освіти (ЗВО). Наведені приклади трансформації ISO 37001:2025 в проєкти освітнього стандарту (на­ціонального рівня або внутрішнього стандарту університету).

  • Open Access

    PROCESS MODEL FOR MEASURING AND ASSESSING THE QUALITY OF EDUCATIONAL SERVICES PROVISION

    by State University of Intellectual Technology and Telecommunications, L. V. Kolomiets, O. I. Kyselyova, О. В. Грабовський, А. А. Haber, О. І. Кисельова

    In the course of the study, a process model was developed for measuring and evaluating the quality of educational services provided by institution of higher education. The basis of the model is the integration of Harringtons function approaches and international standards ISO 25010, ISO 25022. This model allows for a systematic assessment of the quality of the provision of educational services based on clearly defined criteria and indicators. The application of the Harrington function provides the possibility of converting quantitative indicators of quality into a convenient scale of perception, which allows to more accurately reflect the level of satisfaction of consumers of educational services (students, teachers, administration) and facilitates the decision-making process for improving quality. The use of ISO 25010, ISO 25022 standards made it possible to clearly define quality assessment criteria at each stage of the provision of educational services, including such aspects as functionality, reliability, ease of use, efficiency and support. These standards contribute to the formalization of quality measurement processes and increase the transparency of the entire educational cycle. Two groups of methods for evaluating the quality of educational activities of higher education institutions have been developed, namely, preparation for the evaluation of the quality of educational services at the design stage and evaluation of the quality of the provision of educational services at the operational stage. The process model developed as part of the research allows not only to evaluate the final results of training, but also to analyze each stage of the educational process - from planning training programs to evaluating the knowledge of higher education students. This contributes to the timely identification of problems and the implementation of corrective measures to improve the quality of the provision of educational services. The model aligns with modern higher education needs in a globalized, competitive market, based on international standards and addressing stakeholder needs. Its implementation ensures transparency and reliability in internal quality control systems.