Petre Chipurici

This study presents an innovative upcycling methodology for the production of rigid polyurethane (PUR) foams utilizing a biopolyol (BioPol) derived from corn cob waste obtained through microwave-assisted irradiation under acidic catalysis.

Ultrasonication-derived alginate optimizes collagen interaction in chrome-free leather retanning, enhancing biodegradability and reducing waste.

Plastics, once regarded as a revolutionary material shaping modern society, now pose an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to cement factories that burn it together with other fuels. However, with some processing techniques such as catalytic pyrolysis, this fraction could be valorized. In this paper, experiments were carried out in batches at a laboratory-scale installation, with a processing capacity of 1–3 kg of waste. A pyrolysis reactor was connected to a distillation column, enabling separation of the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5–10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions (C1–C6, C6–C10, and C11–C13) in relation to the heavy fractions (C13–C20 and C20+). Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much more easily exploited by burning in an engine that drives an electric generator.

Plastics, once regarded as a revolutionary material shaping modern society, now poses an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to the cement factories that burn it together with other fuels. However, with some processing techniques such catalytic pyrolysis this fraction could be valorized. In this paper the experiments which were carried out at a laboratory scale installation, in batches with a processing capacity of 1-3 kg of waste. The pyrolysis reactor is connected to a distillation column giving the possibility to separate the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5-10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions C1-C6, C6-C10 and C11-C13) in relation to the heavy fractions C13-C20 and C20+. Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments, was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much easier exploited by burning in an engine that drives an electric generator.

Oak bark is a by-product known for its richness in polyphenols, with tanning substances being particularly interesting for their application in different fields. Vegetable tannins are mostly utilized in the leather sector, but are also widely used as adhesives, in cement plasticizers and for medical and agrochemical applications owing to their natural antimicrobial activity. This study aimed to develop a green and efficient pilot-scale technique for extracting polyphenols from oak bark by ultrasound-assisted extraction (UAE) using a modified Dual-Frequency Reactor (DFR). Different parameters, such as extraction time, temperature, and solvent type (water, sodium hydroxide or sodium sulfite and bisulfite solutions) were investigated for their influence on the total phenolic content (TPC) and the quantity of dry extract. Control experiments by conventional methods were also performed. UAE at 50 °C yielded the highest TPC and dry extract (confirmed by ANOVA analysis, p < 0.05) in just 10 min, suggesting that UAE can be considered an energy- and cost-effective alternative to conventional techniques. The most suitable solvent was found to be a 0.5% sodium hydroxide solution. The molecular profile of the extracts was assessed by FTIR-ATR spectroscopy, revealing typical signals of tannins in all extracts. Furthermore, antimicrobial activity tests demonstrated the complete absence of Gram-positive and Gram-negative bacteria in the extracts, ensuring the suitability of the product for different kinds of application.

As a renewable and sustainable resource, lignocellulosic biomass serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The alkaline sonochemical pretreatment emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis to improve the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic-assisted pretreatment revealed a higher delignification of 68% (horn) and 57% (bath) compared with conventional pretreatment. Processes were optimized using a statistical analysis based on a 2³ factorial design. The ratios between sawdust and alkaline solution (R_SL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE/g_substrate) were found as follows: a solid/liquid ratio of R_SL,opt = 1.25 g/100 mL, US amplitude of A_opt = 60%, and pretreatment temperature of t_opt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound-assisted alkaline pretreatment.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

Hedera helix L. contains phytochemicals with good biological properties which are beneficial to human health and can be used to protect plants against different diseases. The aim of this research was to find the most suitable extraction method and the most favorable parameters for the extraction of different bioactive compounds from ivy leaves. Different extraction methods, namely microwave-assisted extraction (MAE), ultrasound-assisted extraction (UAE), and conventional heating extraction (CHE), were used. The most suitable method for the extraction of saponins is MAE with an extraction efficiency of 58%, while for carbohydrates and polyphenols, the best results were achieved via UAE with an extraction efficiency of 61.7% and 63.5%, respectively. The antioxidant activity (AA) of the extracts was also determined. The highest AA was obtained via UAE (368.98 ± 9.01 µmol TR/gDM). Better results were achieved at 50 °C for 10 min of extraction, using 80% ethanol in water as solvent. In order to evaluate their in vitro cytotoxicity, the extracts richest in bioactive compounds were tested on NCTC fibroblasts. Their influence on the DNA content of RAW 264.7 murine macrophages was also tested. Until 200 µg/mL, the extracts obtained via UAE and MAE were cytocompatible with NCTC fibroblasts at 48 h of treatment. Summarizing the above, both MAE and UAE can be employed as green and efficient methods for producing extracts rich in bioactive compounds, exhibiting strong antioxidant properties and good noncytotoxic activity.

Phytochemicals from Hedera helix L. lead to extracts with good biological properties which are beneficial to human health and can be used to protect plants against different diseases. The aim of this research was to find the most suitable extraction method and the most favorable parameters for different bioactive compounds extraction from ivy leaves. Different extraction methods, namely microwave assisted extraction (MAE), ultrasound assisted extraction (UAE), and conventional heating extraction (CHE), were used. The most suitable method for saponins extraction is MAE with an extraction efficiency of 58%, while for carbohydrates and polyphenols the best results were achieved by UAE with an extraction efficiency of 61.7% and 63.5%, respectively. The antioxidant activity (AA) of the extracts was also determined. The highest AA was obtained by UAE (368.98±9.01 µmol TR/gDM). Better results were achieved at 50 °C for 10 min of extraction, using 80% ethanol in water as solvent. In order to evaluate their in vitro cytotoxicity, the extracts richest in bioactive compounds were tested on NCTC fibroblasts. Their influence on the DNA content of RAW 264.7 murine macrophages was also tested. Until 200 µg/mL, the extracts obtained by UAE and MAE were cytocompatible with NCTC fibroblasts at 48 h of treatment.

Currently there is a drive towards the minimisation and reclamation of valuable materials from the waste products of the food and beverage industry. This can be achieved through the extraction of residual nutraceuticals from such materials. Tomato pomace contains carotenoids and other chemicals which can be extracted directly into edible oils to improve the health-giving properties of such oils. We report here a novel green solvent, fatty acid ethyl esters (FAEE), which is significantly more effective than sunflower oil and hexane for the extraction of lycopene and beta-carotene from tomato skin waste. FAEE are a non-toxic renewable resource that is environmentally friendly and to our knowledge has never been used as a vegetal extraction fluid. The efficiency of FAEE extraction was significantly improved relative to both sunflower oil and hexane under ultrasound-assisted extraction (UAE) conditions. In addition, FAEE have the additional and significant advantage that once enriched with the extracted nutraceuticals can be used directly as a food additive.