RNRadoslav Novotný

Radoslav Novotný

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Radoslav Novotný has a total of 96 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Insights into the hydration reactions of low-carbon cements

    by Tomáš Iľanovský, Martin T. Palou, Radoslav Novotný, Masilko Jiří, Matúš Žemlička, Wilińska Iwona, Peter Czirák

  • Open Access

    Carbonation reactivity of hydrated calcium aluminate phases: A comparative study

    by Jan Koplík, Radoslav Novotný, Jiří Švec, Martin Sedlačík, Jiří Másilko

  • Open Access

    Thermal analysis, hydration kinetics, and rheological behaviour of non-kaolinitic waste clay materials for low-cost mixed cement

    by Vojtěch Florian, Pavel Šiler, Patrik Sokola, Radoslav Novotný, Jiří Másilko, Jiří Švec, OndřEj Kunovský, Michal Marko, František Šoukal


  • Open Access

    Calorimetric study of gamma dicalcium silicate during the accelerated carbonation process

    by Jiří Másilko, Eva Bartoníčková, Radoslav Novotný, Jiří Švec, Martin Sedlačík, Vladislav Cába, David Markusík, Jan Koplík, Lukáš Kalina, Matěj BřEzina

    This paper is focused on investigating the chemical processes during the carbonation of a gamma dicalcium silicate ( γ -C 2 S). Isothermal calorimetry, in particular, provides valuable insights into the heat flow associated with the carbonation process under controlled conditions. The carbonation reactivity of γ -C 2 S under varying CO 2 pressure and water-to-solid ratio (w/s) using isothermal calorimetry was examined. The influence of these parameters on the extent of the carbonation reaction and the resulting proportions of calcium carbonate polymorphs (calcite, vaterite, and aragonite) was explored. Furthermore, the carbonation products were characterized using X-ray diffraction analysis (XRD), thermogravimetric and differential thermal analysis (TG–DTA), and scanning electron microscopy (SEM) to provide a comprehensive understanding of the reaction mechanism and the properties of the formed products. The results indicated that the partial pressure of CO 2 had a limited influence on the carbonation degree, whereas the water-to-solid ratio greatly enhanced the extent of the reaction. Aragonite and calcite were identified as the predominant reaction products. Subsequent analyses at high temperatures revealed a transformation of aragonite into calcite at approximately 500 °C, followed by its decomposition into calcium oxide approximately at 800 °C.


  • Open Access

    Structural and compositional changes in ladle furnace slag during CO2 capture

    by Vladislav Cába, Radoslav Novotný, Martin Sedlačík, Vlastimil Bílek, Jiří Másilko

    To facilitate the optimization of carbon capture and utilization through ladle furnace slag (LFS), it is essential to develop a deeper understanding of the interrelated evolution of reaction, microstructure, and performance. To this end, a novel carbonation-isothermal-calorimetry setup was devised and integrated with multiscale characterization (including TG–DTA, CS analysis, XRD, SEM–EDS, MIP, and DFT) to observe the reaction kinetics of LFS in real time. This comprehensive strategy reveals a significant temporal mismatch between chemical conversion and the development of mechanical properties. Notably, the majority of the chemical reaction and CO 2 sequestration is completed within the first 30 min, as confirmed by calorimetry and thermal analysis. In stark contrast, the primary increase in compressive strength is significantly delayed, occurring rapidly only between 30 and 45 min. This decoupling clarifies that the ultimate performance of the material is not kinetically limited by the initial rapid CO 2 reaction. Instead, strength development is governed by subsequent diffusion-limited processes, including the recrystallization of initial metastable phases into stable calcite and the progressive densification of the silica-rich binding matrix through pore refinement.


  • Open Access

    Comparison of commercial nitrate-based accelerators and their pure constituents on hydration kinetics, composition, and hydration degree of zinc oxide blended Portland cement

    by Lukas Matejka, Pavel Siler, Jiri Svec, Jiri Masilko, Jan Koplik, Martin Sedlacik, Radoslav Novotny, Frantisek Soukal

    The rising concentration of zinc in ordinary Portland cement has a concerning impact on the behaviour of cement-based mortars by drastically prolonging setting time and decreasing early mechanical properties. The current theory behind the mechanism of the effect of this contaminant is the depletion of Ca2+ ions from pore solution and the formation of a semipermeable layer of CaZn2(OH)6·2 H2O on the surface of silicate cement phases, thus retarding their hydration. The cement industry employs various additives to counteract these problems in the form of water-soluble salts of alkali metals such as sodium nitrate. The induction period, which describes the time interval before the setting of cement, can be easily determined by various calorimetric methods. One of the simplest methods is isoperibolic calorimetry, which gives information about the natural behaviour of samples in a set environment by measuring temperature changes in the sample placed in a stable ambient environment. This factor can be determined using differential thermal analysis, indicating the degree of retardation. X-ray diffraction and scanning electron microscopy can also study composition changes. These methods are commonly used to determine phase changes in materials. Pure nitrates proved to be more effective at reducing setting time than commercial additives. Calcium and sodium nitrates reduced the setting time of zinc-contaminated Portland cement from ~ 200 h to about 60 h. The commercial accelerators reduced setting time to about 120 h. Every accelerator used to mitigate retardation of setting reduced setting time without compromising mechanical properties. The highest doses of pure nitrates slightly increased setting time and decreased compressive strength, probably due to the destabilisation of ettringite in a high alkali environment and the displacement of sulphate ions by nitrate ions. This indicates a hard limit for the dose of nitrates. This phenomenon was not observed in high doses of commercial accelerators.


  • Open Access

    Influence of alkali metal formates and calcium formate on workability, hydration and basic properties of reactive powder concrete

    by Nikola Šuleková, František Šoukal, Radoslav Novotný, Martin Sedlačík, Jiří Švec, Jiří Másilko, Petr Ptáček, Luboš Bocian, Jan Hajzler, Michal Marko

    This work aims to study whether it would be possible to use alkali metal formates and calcium formate in order to increase the workability of reactive powder concrete (RPC) and how these additives affect hydration, mechanical properties and mineralogical composition of RPC. These substances were added together with superplasticizer. Therefore, paper deals with possibility of increase in workability which would be higher when compared to the sole addition of only the superplasticizer themself. The effect of alkali metal formates and their replacement with calcium formate on slump flow, mechanical properties and pH of RPC was studied. Furthermore, the influence of potassium formate and its replacement with calcium formate and with calcium oxide on the hydration of RPC was observed with the help of isothermal calorimetry and thermal analysis. The results showed that the addition of studied compounds allows to achieve an increase in RPC slump flow. However, it is necessary to add these substances in an optimal ratio of alkali metal formate/calcium formate because a higher content of calcium formate leads to a decrease in slump flow. For ideal ratios, the compressive strength after 90 days is still above 218 MPa and the flexural strength is still above 23 MPa. In calorimetric measurements, it was observed that the addition of potassium formate leads to a decrease in the total amount of heat developed in the induction period. According to thermal analysis, additions of the studied additives to RPC caused changes in the content of portlandite and calcite.


  • Open Access

    Hydration kinetics of C3A: effect of lithium, copper and sulfur-based mineralizers

    by Eva Bartonickova, Petr Ptacek, Radoslav Novotny, Jakub Palovcik, Jiri Masilko, Jiri Svec, Martin Sedlacik, Jan Koplik, Theodor Stanek, Dusan Hemzal

    Calcium aluminate phases have a particular effect on the early heat release during setting initiation and have a substantial influence on the further workability of ordinary Portland cement. The nature of the calcium aluminate hydration products and its kinetics strongly depends on sulfate content and humidity. The effect of mineralisers on melt formation and viscosity is well described for calcium silicate systems, but information is still lacking for calcium aluminates. Therefore, the synergistic effect on the crystal structure and hydration mechanism of the tricalcium aluminate phase of the addition of mineralizers, i.e. Li2O, CuO, SO3 to the raw meal is here investigated. Co-doped calcium aluminate structures were formed during high-temperature treatment. Thermal analysis (TG–DTA and heating microscopy) was used to describe the ongoing high-temperature reaction. Resulting phase composition was dependent on the concentration of the mineralizer. While phase pure system was prepared with low mineralizer concentrations, with increasing mineralizer content the secondary phases were formed. Raman spectroscopy and XPS analysis were used to investigate the cation substitution and to help describe the cations bonding in co-doped calcium aluminate system. Prepared powders have been hydrated in a controlled manner at different temperatures (288, 298, 308 K). The resulting calorimetric data have been used to investigate the hydration kinetics and determine the rate constant of hydration reaction. First-order reaction (FOR) model was here applied for the activation energy and frequency factor calculations. The metastable and stable calcium aluminate hydrates were formed according to initial phase composition. In phase pure systems with low S content, the formation of stable and metastable hydrates was depended on the reaction temperature. Conversely, in systems with secondary phases and higher S content, the hydration mechanism resembled that which appears in calcium sulfoaluminates.


  • Open Access

    The Effects of Silica Fume and Superplasticizer Type on the Properties and Microstructure of Reactive Powder Concrete

    by František Šoukal, Luboš Bocian, Radoslav Novotný, Lucie Dlabajová, Nikola Šuleková, Jan Hajzler, Ondřej Koutný, Martina Drdlová

    This paper deals with the optimization of reactive powder concrete mixtures with respect to the addition of silica fume and the type of polycarboxylate superplasticizer used. First, the properties of reactive powder concrete with eight different commercial polycarboxylate superplasticizers were tested in terms of workability, specific weight, and mechanical properties. It was found that different commercially available superplasticizers had significant effects on the slump flow, specific weight, and compressive and flexural strengths. The optimal superplasticizer (BASF ACE430) was selected for further experiments in order to evaluate the influences of silica fume and superplasticizer content on the same material properties. The results showed that the silica fume and superplasticizer content had considerable effects on the mini-cone slump flow value, specific weight, flexural and compressive strengths, and microstructure. There were clearly visible trends and local minima and maxima of the measured properties. The optimal reactive powder concrete mixture had a composition of 3.5–4.0% superplasticizer and 15–25% silica fume.


  • Open Access

    Influence of Fumed Nanosilica on Ballistic Performance of UHPCs

    by David Markusík, Luboš Bocian, Radoslav Novotný, Jakub Palovčík, Markéta Hrbáčová

    This research delves into the potential use of fumed nanosilica in ultra-high performance concrete for ballistic protection. First, the mechanical properties, slump flow, and specific gravity of UHPC with different contents of Aerosil 200 were determined. Then, calorimetric studies were conducted on these cement composites. Lastly, the differential efficiency factor and spalling area of UHPC with fumed nanosilica were determined. It was found out that the slump flow, the mechanical properties, and differential efficiency factor are slightly decreased by the addition of fumed nanosilica. However, the addition of the fumed nanosilica is beneficial in terms of the spalling area decrease and it is highly reactive during the induction period. Some of the results are supported by BSEM imaging.