Nelson Pereira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Nelson Pereira has a total of 133 co-authors. Here are the top co-authors by number of shared publications:
- Senentxu Lanceros Mendez
BCMaterials, Basque Center for Materials, Applications and Nanostructures, UPV/EHU Science Park, 48940 Leioa, Spain
24 shared publications - Pedro Martins
Centre of Molecular and Environmental Biology (CBMA), University of Minho, 4710-057 Braga, Portugal
9 shared publications - Carmen Rial Tubio
BCMaterials, Basque Center for Materials Applications and Nanostructures UPV/EHU Science Park Leioa Spain
5 shared publications - Daniela Maria Correia
University of Minho
5 shared publications - Vitor Correia
Centro/Departamento de Física, Universidade do Minho, Braga, Portugal
5 shared publications - Ana Catarina Lima
Centro/Departamento de Física, Universidade do Minho, 4710-057 Braga, Portugal
4 shared publications
Latest Publications
- 20 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (43) , 20107-20118
Photopyroelectric Nanocomposites: A Strategy for Continuous Self-Disinfection of High-Traffic Surfaces
High-traffic surfaces act as persistent reservoirs for pathogen transmission, motivating the development of durable, non-leaching self-disinfecting coatings. Here, gold nanostars were integrated into poly(vinylidene fluoride-co-trifluoroethylene) [P(VDF−TrFE)] to create an electroactive plasmonic nanocomposite that converts light stimuli into antibacterial surface activity. Under red/near-infrared illumination, localized surface plasmon resonance (LSPR)-mediated heating at the nanofiller-matrix interface triggers the pyroelectric response of P(VDF−TrFE). This photothermal-pyroelectric coupling produced nanostar dose-dependent antibacterial and antibiofilm activity against Escherichia coli and Staphylococcus aureus, achieving bacterial reductions exceeding 90% under illumination while maintaining biocompatibility with fibroblasts under standard culture conditions. Importantly, the inherent piezoelectric response of P(VDF−TrFE) enables surface charge generation under mechanical pressure, suggesting a complementary activation pathway relevant to frequently touched interfaces. This work establishes a versatile, durable, and non-leaching nanomaterial platform for multi-responsive antimicrobial surfaces in high-contact settings.
- 20 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (43) , 20107-20118
Photopyroelectric Nanocomposites: A Strategy for Continuous Self-Disinfection of High-Traffic Surfaces
High-traffic surfaces act as persistent reservoirs for pathogen transmission, motivating the development of durable, non-leaching self-disinfecting coatings. Here, gold nanostars were integrated into poly(vinylidene fluoride-co-trifluoroethylene) [P(VDF−TrFE)] to create an electroactive plasmonic nanocomposite that converts light stimuli into antibacterial surface activity. Under red/near-infrared illumination, localized surface plasmon resonance (LSPR)-mediated heating at the nanofiller-matrix interface triggers the pyroelectric response of P(VDF−TrFE). This photothermal-pyroelectric coupling produced nanostar dose-dependent antibacterial and antibiofilm activity against Escherichia coli and Staphylococcus aureus, achieving bacterial reductions exceeding 90% under illumination while maintaining biocompatibility with fibroblasts under standard culture conditions. Importantly, the inherent piezoelectric response of P(VDF−TrFE) enables surface charge generation under mechanical pressure, suggesting a complementary activation pathway relevant to frequently touched interfaces. This work establishes a versatile, durable, and non-leaching nanomaterial platform for multi-responsive antimicrobial surfaces in high-contact settings.
- Open Access
- 14 October 2026
- Published by Elsevier in Applied Materials Today
- Vol. 53
Textile-integrated iontronic foam for scalable and robust pressure sensing in wearable systems
- 14 October 2026
- Published by Elsevier in Applied Materials Today
- Vol. 53
Open AccessTextile-integrated iontronic foam for scalable and robust pressure sensing in wearable systems
- 24 September 2026
- Published by Wiley in Polymer Composites
Sustainable High‐Performance Structural Adhesives With Intrinsic Thermo‐ and Piezoresistive Sensing Capabilities
Epoxy adhesives are key enablers of lightweight, high‐performance structures, providing efficient bonding of dissimilar materials for demanding engineering applications. Meanwhile, sustainable bio‐based formulations with performances comparable to petroleum‐derived systems are emerging as environmentally friendly alternatives. By incorporating carbon nanotubes (CNTs), these adhesives become multifunctional materials capable of simultaneously carrying loads and monitoring their structural state. Herein, a commercial Araldite epoxy and a bio‐based resin, together with their composites containing 1, 3, and 5 wt% CNTs, were processed using a three‐roll mill and systematically characterized. The bioresin exhibited higher tensile strength but lower strain‐at‐break than Araldite, while CNT incorporation caused only a slight reduction in the mechanical performance of both matrices. Although lap shear strength decreased after functionalization, all formulations remained suitable for semi‐structural bonding applications. Thermoresistive sensitivity was maximized near the electrical percolation threshold, reaching ST ≈ −0.29 and −0.23% °C −1 between 30°C and 100°C for Araldite and the bioresin, respectively. Load sensing was successfully demonstrated under shear loading in single‐lap joints up to 50 N, with piezoresistive sensitivities approaching 300 Ω/N for Araldite containing 3 wt% CNTs and 25 Ω/N for the bioresin with 5 wt% CNTs. These findings demonstrate that both petroleum‐based and bio‐based epoxy adhesives can be transformed into sustainable multifunctional bonding materials with integrated thermo‐ and piezoresistive sensing capabilities for next‐generation structural applications.
- 24 September 2026
- Published by Wiley in Polymer Composites
Sustainable High‐Performance Structural Adhesives With Intrinsic Thermo‐ and Piezoresistive Sensing Capabilities
Epoxy adhesives are key enablers of lightweight, high‐performance structures, providing efficient bonding of dissimilar materials for demanding engineering applications. Meanwhile, sustainable bio‐based formulations with performances comparable to petroleum‐derived systems are emerging as environmentally friendly alternatives. By incorporating carbon nanotubes (CNTs), these adhesives become multifunctional materials capable of simultaneously carrying loads and monitoring their structural state. Herein, a commercial Araldite epoxy and a bio‐based resin, together with their composites containing 1, 3, and 5 wt% CNTs, were processed using a three‐roll mill and systematically characterized. The bioresin exhibited higher tensile strength but lower strain‐at‐break than Araldite, while CNT incorporation caused only a slight reduction in the mechanical performance of both matrices. Although lap shear strength decreased after functionalization, all formulations remained suitable for semi‐structural bonding applications. Thermoresistive sensitivity was maximized near the electrical percolation threshold, reaching ST ≈ −0.29 and −0.23% °C −1 between 30°C and 100°C for Araldite and the bioresin, respectively. Load sensing was successfully demonstrated under shear loading in single‐lap joints up to 50 N, with piezoresistive sensitivities approaching 300 Ω/N for Araldite containing 3 wt% CNTs and 25 Ω/N for the bioresin with 5 wt% CNTs. These findings demonstrate that both petroleum‐based and bio‐based epoxy adhesives can be transformed into sustainable multifunctional bonding materials with integrated thermo‐ and piezoresistive sensing capabilities for next‐generation structural applications.
- Open Access
- 28 April 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
Electrical double-layer based wearable tensile and pressure sensors: optimizing materials and architecture for improved sensing response
A materials-to-architecture design rule for iontronic textiles optimizes dense films for strain and porous scaffolds for pressure, enabling motion discrimination.
- 28 April 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
Open AccessElectrical double-layer based wearable tensile and pressure sensors: optimizing materials and architecture for improved sensing response
A materials-to-architecture design rule for iontronic textiles optimizes dense films for strain and porous scaffolds for pressure, enabling motion discrimination.
- Open Access
- 1 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (8)
3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs
This work presents the development and characterization of 3D‐printed mechanically driven giant magnetoresistance (GMR) sensors using self‐compliant spring structures and piezoresistive materials. Fused deposition modeling 3D printing has been employed to fabricate sensors from conductive and magnetic polylactic acid composite materials, enabling low‐cost and highly customizable designs. Three sensor topologies were fabricated to optimize magnetoresistive and piezoresistive responses. Electromechanical and magnetic characterizations showed that the self‐compliant spring arm width influences the device mechanical stiffness, piezoresistive response, and magnetoresistive sensitivity. Sensitivities up to 0.34%/mm for piezoresistive sensors with a 3‐mm arm under direct mechanical deformation and 0.77%/mT for the magnetoresistive sensors with a 1‐mm arm were obtained, with a response 10 times higher in sensitivity than other printed spin‐dependent GMR devices in the literature. The applicability was demonstrated in pressure sensing and noncontact magnetic position detection, integrated in a Bluetooth low energy application. The sensors showcased reliable performance under dynamic conditions at a frequency range of 0.1, 0.25, and 0.5 Hz, highlighting their potential in automotive, robotics, and consumer electronics. This work establishes self‐compliant structural design as an effective tool for fabricating mechanically driven GMR‐like sensors using low‐cost, additive manufacturing techniques, allowing further integration of geometry‐driven devices into increasingly interconnected IoT networks.
- 1 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (8)
Open Access3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs
This work presents the development and characterization of 3D‐printed mechanically driven giant magnetoresistance (GMR) sensors using self‐compliant spring structures and piezoresistive materials. Fused deposition modeling 3D printing has been employed to fabricate sensors from conductive and magnetic polylactic acid composite materials, enabling low‐cost and highly customizable designs. Three sensor topologies were fabricated to optimize magnetoresistive and piezoresistive responses. Electromechanical and magnetic characterizations showed that the self‐compliant spring arm width influences the device mechanical stiffness, piezoresistive response, and magnetoresistive sensitivity. Sensitivities up to 0.34%/mm for piezoresistive sensors with a 3‐mm arm under direct mechanical deformation and 0.77%/mT for the magnetoresistive sensors with a 1‐mm arm were obtained, with a response 10 times higher in sensitivity than other printed spin‐dependent GMR devices in the literature. The applicability was demonstrated in pressure sensing and noncontact magnetic position detection, integrated in a Bluetooth low energy application. The sensors showcased reliable performance under dynamic conditions at a frequency range of 0.1, 0.25, and 0.5 Hz, highlighting their potential in automotive, robotics, and consumer electronics. This work establishes self‐compliant structural design as an effective tool for fabricating mechanically driven GMR‐like sensors using low‐cost, additive manufacturing techniques, allowing further integration of geometry‐driven devices into increasingly interconnected IoT networks.
- Open Access
- 16 November 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 11 (4)
Ionic Liquid‐Enhanced 3D Printed Flexible Resin for Pressure‐Sensing Applications
Iontronic materials show high performance for applications as pressure sensors due to the formation of the electric double layers (EDLs) at the dielectric/electrode interface. The properties of iontronic materials can be tuned, allowing the sensor to be customized for varied pressure ranges and ambient conditions. Furthermore, additive printing techniques enable to obtain customized cost‐effective complex sensor designs, opening up new applications in the fields of medical devices, automotive systems, and consumer electronics. This work demonstrates the manufacturing process of a pressure sensor by stereolithography (SLA) 3D printing of a Liqcreate Flexible X resin in a gyroid framework, accounting for structural density variations. Furthermore, different concentrations (5 and 20% wt.) of the ionic liquid (IL) 1‐butyl‐3‐methyl imidazolium thiocyanate ([Bmim][SCN]) are used to tune the EDL and maximize the sensor sensitivity. The capacitance response to applied pressure is analyzed across different designs. The configuration with 20% wt. IL content and lower quantity of pores exhibited superior performance, achieving a pressure sensitivity of 0.065 kPa −1 throughout a pressure range of 60 kPa. This study demonstrated the simple manufacturing process and ability to improve commercially available resins with ionic liquid, to achieve highly customized sensors.
- 16 November 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 11 (4)
Open AccessIonic Liquid‐Enhanced 3D Printed Flexible Resin for Pressure‐Sensing Applications
Iontronic materials show high performance for applications as pressure sensors due to the formation of the electric double layers (EDLs) at the dielectric/electrode interface. The properties of iontronic materials can be tuned, allowing the sensor to be customized for varied pressure ranges and ambient conditions. Furthermore, additive printing techniques enable to obtain customized cost‐effective complex sensor designs, opening up new applications in the fields of medical devices, automotive systems, and consumer electronics. This work demonstrates the manufacturing process of a pressure sensor by stereolithography (SLA) 3D printing of a Liqcreate Flexible X resin in a gyroid framework, accounting for structural density variations. Furthermore, different concentrations (5 and 20% wt.) of the ionic liquid (IL) 1‐butyl‐3‐methyl imidazolium thiocyanate ([Bmim][SCN]) are used to tune the EDL and maximize the sensor sensitivity. The capacitance response to applied pressure is analyzed across different designs. The configuration with 20% wt. IL content and lower quantity of pores exhibited superior performance, achieving a pressure sensitivity of 0.065 kPa −1 throughout a pressure range of 60 kPa. This study demonstrated the simple manufacturing process and ability to improve commercially available resins with ionic liquid, to achieve highly customized sensors.
- 22 July 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 10 (21)
3D‐Printed Linear Variable Differential Transformer (LVDT) for Cost‐Effective Displacement Sensing
The IoT and Industry 4.0 have increased demand for smart, wireless, customized, and sustainable sensors in industrial environments. Linear Variable Differential Transformers (LVDTs) are crucial for precision displacement sensing due to their high resolution and durability, but face challenges like complex assembly and high manufacturing costs. In this work, a fully printed LVDT position/force sensor is presented, fabricated using fused filament fabrication (FFF) and 5‐axis piezo‐jet printing, enabling the integration of complex geometries and conductive coil patterns directly onto curved surfaces. Two core configurations are evaluated: a commercial MnZn core and a magnetic poly(lactic acid) (PLA) composite core printed via FFF. Electromagnetic and magnetic characterizations revealed that the MnZn core provided superior sensitivity of 1054.3 ± 11.32 µV·mm −1 with respect to the printed core, which exhibited a lower sensitivity of 3.86 ± 0.07 µV·mm −1 . The sensors' wireless are integrated with a custom signal conditioning circuit based on the AD598 and an ESP32 microcontroller, allowing real‐time data transmission via Bluetooth Low Energy (BLE). The sensor is implemented in a pressure sensing application, showcasing a linear response with a sensitivity of 3.18 ± 0.22 mV·N −1 , offering a highly versatile, scalable, and low‐cost solution for next‐generation industrial sensing in IoT‐enabled environments.
- 22 July 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 10 (21)
3D‐Printed Linear Variable Differential Transformer (LVDT) for Cost‐Effective Displacement Sensing
The IoT and Industry 4.0 have increased demand for smart, wireless, customized, and sustainable sensors in industrial environments. Linear Variable Differential Transformers (LVDTs) are crucial for precision displacement sensing due to their high resolution and durability, but face challenges like complex assembly and high manufacturing costs. In this work, a fully printed LVDT position/force sensor is presented, fabricated using fused filament fabrication (FFF) and 5‐axis piezo‐jet printing, enabling the integration of complex geometries and conductive coil patterns directly onto curved surfaces. Two core configurations are evaluated: a commercial MnZn core and a magnetic poly(lactic acid) (PLA) composite core printed via FFF. Electromagnetic and magnetic characterizations revealed that the MnZn core provided superior sensitivity of 1054.3 ± 11.32 µV·mm −1 with respect to the printed core, which exhibited a lower sensitivity of 3.86 ± 0.07 µV·mm −1 . The sensors' wireless are integrated with a custom signal conditioning circuit based on the AD598 and an ESP32 microcontroller, allowing real‐time data transmission via Bluetooth Low Energy (BLE). The sensor is implemented in a pressure sensing application, showcasing a linear response with a sensitivity of 3.18 ± 0.22 mV·N −1 , offering a highly versatile, scalable, and low‐cost solution for next‐generation industrial sensing in IoT‐enabled environments.
- Open Access
- 26 August 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (36) , 48547-48555
AC/DC Magnetic Field Sensing Based on a Piezoelectric Polymer and a Fully Printed Planar Spiral Coil
Additive manufacturing (AM) is emerging as an eco-friendly method for minimizing waste, as the demand for responsive materials in IoT and Industry 4.0 is on the rise. Magnetoactive composites, which are manufactured through AM, facilitate nonintrusive remote sensing and actuation. Printed magnetoelectric composites are an innovative method that utilizes the synergies between magnetic and electric properties. The study of magnetoelectric effects, including the recently validated piezoinductive effect, demonstrates the generation of electric voltage through external AC and DC magnetic fields. This shift in magnetic sensors, utilizing piezoinductive effect of the piezoelectric polymer poly(vinylidene fluoride), PVDF, eliminates the need for magnetic fillers in printed devices, aligning with sustainability principles, essential for the deployment of IoT and Industry 4.0. The achieved sensitivity surpasses other studies by 100 times, showcasing linear outputs for both applied AC and DC magnetic fields. Additionally, the sensor capitalizes on the linear phase shift of the generated signal with an applied DC magnetic field, an unprecedented effect. Thus, this work introduces a remarkable magnetoactive device with a sensitivity of ST = 95.1 ± 0.9 μV Oe-1 mT-1, a significantly improved performance compared to magnetoelectric devices using polymer composites. As a functional proof of concept of the developed system, a magnetic position sensor has been demonstrated.
- 26 August 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (36) , 48547-48555
Open AccessAC/DC Magnetic Field Sensing Based on a Piezoelectric Polymer and a Fully Printed Planar Spiral Coil
Additive manufacturing (AM) is emerging as an eco-friendly method for minimizing waste, as the demand for responsive materials in IoT and Industry 4.0 is on the rise. Magnetoactive composites, which are manufactured through AM, facilitate nonintrusive remote sensing and actuation. Printed magnetoelectric composites are an innovative method that utilizes the synergies between magnetic and electric properties. The study of magnetoelectric effects, including the recently validated piezoinductive effect, demonstrates the generation of electric voltage through external AC and DC magnetic fields. This shift in magnetic sensors, utilizing piezoinductive effect of the piezoelectric polymer poly(vinylidene fluoride), PVDF, eliminates the need for magnetic fillers in printed devices, aligning with sustainability principles, essential for the deployment of IoT and Industry 4.0. The achieved sensitivity surpasses other studies by 100 times, showcasing linear outputs for both applied AC and DC magnetic fields. Additionally, the sensor capitalizes on the linear phase shift of the generated signal with an applied DC magnetic field, an unprecedented effect. Thus, this work introduces a remarkable magnetoactive device with a sensitivity of ST = 95.1 ± 0.9 μV Oe-1 mT-1, a significantly improved performance compared to magnetoelectric devices using polymer composites. As a functional proof of concept of the developed system, a magnetic position sensor has been demonstrated.
- Open Access
- 5 April 2024
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 6 (4) , 2152-2160
Improving Definition of Screen-Printed Functional Materials for Sensing Application
Screen printing is one of the most used techniques for developing printed electronics. It stands out for its simplicity, scalability, and effectivity. Specifically, the manufacturing of hybrid integrated circuits has promoted the development of the technique, and the photovoltaic industry has enhanced the printing process by developing high-performance metallization pastes and high-end screens. In recent years, fine lines of 50 μm or smaller are about to be adopted in mass production, and screen printing has to compete with digital printing techniques such as inkjet printing, which can reach narrower lines. In this sense, this work is focused on testing the printing resolution of a high-performance stainless-steel screen with commercial conductive inks and functional lab-made inks based on reduced graphene oxide using an interdigitated structure. We achieved electrically conductive functional patterns with a minimum printing resolution of 40 μm for all inks.
- 5 April 2024
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 6 (4) , 2152-2160
Open AccessImproving Definition of Screen-Printed Functional Materials for Sensing Application
Screen printing is one of the most used techniques for developing printed electronics. It stands out for its simplicity, scalability, and effectivity. Specifically, the manufacturing of hybrid integrated circuits has promoted the development of the technique, and the photovoltaic industry has enhanced the printing process by developing high-performance metallization pastes and high-end screens. In recent years, fine lines of 50 μm or smaller are about to be adopted in mass production, and screen printing has to compete with digital printing techniques such as inkjet printing, which can reach narrower lines. In this sense, this work is focused on testing the printing resolution of a high-performance stainless-steel screen with commercial conductive inks and functional lab-made inks based on reduced graphene oxide using an interdigitated structure. We achieved electrically conductive functional patterns with a minimum printing resolution of 40 μm for all inks.