Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hironori Nakajima has a total of 177 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Transient Behavior of Liquid Water Permeability in the Porous Transport Layer for an Interdigitated Anode Flow Field of a Polymer Electrolyte Membrane Water Electrolyzer with Internal Gas–Liquid

    by Hironori Nakajima, Asuka Sakado, Sae Nishitani, Motohiko Sato, Asuka Shima, Yoshitsugu Sone

    A novel interdigitated flow field for polymer electrolyte membrane (PEM) water electrolyzers has been developed for both space and ground applications1), which are supposed to work in a hybrid system with a low temperature Sabatier reactor for effective use of heat2),3). This design features separate oxygen exhaust channels and liquid water feed channels, enabling the separation of oxygen gas and liquid water within the flow channels without relying on buoyancy. As a result, it eliminates the need for water circulators to remove bubbles in electrolyzers and external separators that rely on natural or centrifugal buoyancy. In this electrolyzer, pressurized liquid water is injected in the in-plane direction from the water channels to the catalyst layer through an anode porous transport layer (PTL)1). The produced oxygen gas is discharged in the through-plane direction of the PTL to the oxygen channels, utilizing the capillary pressure in a hydrophobic PTL. This study conducted liquid water permeability tests on a commercial platinum-coated titanium PTL with pressurized liquid water by measuring the weight of liquid water that penetrated through the PTL to the PTL surface under ambient air pressure. The results show a gradual decrease in permeability over time for different liquid water pressures. This permeability is a key parameter for optimizing the structural design of this electrolyzer. Similar trends have been observed for hydrophobic carbon fiber PTLs with and without a microporous layer in our previous report4). Additionally, a test on the PTL after drying revealed partial recovery of permeability. Thus the formation of liquid water networks inside the PTL may contribute to the observed decrease in permeability. This phenomenon is a critical issue not only for this electrolyzer but also for the conventional PEM electrolyzer. Acknowledgment This study is based on results obtained from a project, JPNP21014, "Development of Innovative Methanation Technology Using Low-Temperature Processes, Green Innovation Fund Project", commissioned by the New Energy and Industrial Technology Development (NEDO). We would like to thank the Innovative Methanation Technology Development Team at Tokyo Gas Co., Ltd. for their valuable discussions. References 1) H. Nakajima, V. Vediyappan, H. Matsumoto, M. Sato, O.S. Mendoza-Hernandez, A. Shima, and Y. Sone, Water Transport Analysis in a Polymer Electrolyte Electrolysis Cell Comprised of Gas/Liquid Separating Interdigitated Flow Fields, Electrochemistry, 90 (2022) 017002. https://doi.org/10.5796/electrochemistry.21-00097 2) H. Nakajima, A. Shima, M. Inoue, T. Abe, H. Matsumoto, O.S. Mendoza-Hernandez, and Y. Sone, Three-Dimensional Numerical Modeling of a Low-Temperature Sabatier Reactor for a Tandem System of CO2 Methanation and Polymer Electrolyte Membrane Water Electrolysis, Electrochemistry, 90 (2022) 22–00035. https://doi.org/10.5796/electrochemistry.22-00035 3) A. Shima, M. Sakurai, Y. Sone, H. Nakajima, M. Inoue, and T. Abe, Improvement of the Full-Scale Model of Carbon Dioxide Reduction-Oxygen Production Tandem Reactor, in: 53rd International Conference on Environmental Systems, 2024: ICES-2024-120. https://hdl.handle.net/2346/98827 4) S. Kubota, H. Nakajima, M. Sato, A. Shima, M. Sakurai, and Y. Sone, Liquid Water Permeability in a Hydrophobic Microporous Layer for the Anode Interdigitated Flow Field of a Gas-Liquid Separating Polymer Electrolyte Membrane Water Electrolyzer, ECS Transactions, 112 (4) (2023) 207-214. https://doi.org/10.1149/11204.0207ecst

  • Data-Driven Surrogate Model Trained on Experimentally Validated Multiphysics Simulations for High-Temperature Polymer Electrolyte Membrane Fuel Cell Stacks for Electric Aircraft Propulsion

    by Takumi Matsuda, Haruya Oka, Yusaku Katsuki, Hironori Nakajima, Chihiro Inoue

    Electrified propulsion systems powered by hydrogen-fueled fuel cells can potentially reduce carbon dioxide emissions from aircraft. However, achieving a substantial increase in the gravimetric/volumetric power density of fuel cell systems poses a considerable challenge. In this study, we focus on high temperature polymer electrolyte membrane fuel cells (HT-PEMFCs) working between 100 and 200°C. To design an HT-PEMFC stack incorporated in an optimized system for an electric aircraft, we have developed a numerical model that employs the finite element method (FEM) (COMSOL Multiphysics) to couple electrochemistry, gas diffusive and convective transports, and heat transfer in fuel cell components such as separators, gas flow channels, gas diffusion layers, catalyst layers, and a PEM. The model is experimentally validated using current density distributions acquired in situ via the electrode segmentation method1). We thereby three-dimensionally visualized the current, hydrogen, oxygen, and water vapor concentration distributions, as well as the temperature distribution in a single cell. We further develop a machine learning (surrogate) model using data outputs from the FEM model as training data to reduce the computational costs2) for the fuel cell stack model incorporated into a system-level numerical model. Acknowledgement This study is based on results obtained from a project, JPNP14004 (Innovative Energy Conversion and Propulsion System Technology for Fuel Cell Aircraft, Feasibility Study Program on Energy and New Environmental Technology), commissioned by the New Energy and Industrial Technology Development Organization (NEDO). We are indebted to Boeing Research & Technology, Boeing Japan for their support and discussions. We are also grateful to Professor Motoaki Kawase of Kyoto University for his fruitful suggestions. Thanks are offered to Professor Kohei Ito and Associate Professor Tatsumi Kitahara of Kyushu University for their valuable discussions. Referemces 1) H. Oka, Y. Katsuki, H. Nakajima, C. Inoue, Numerical Modeling of a Polymer Electrolyte Membrane Fuel Cell for Electric Aircraft Propulsion, ECS Transactions 114 (2024) 575–580. https://doi.org/10.1149/11405.0575ecst. 2) Y. Chi, K. Yokoo, H. Nakajima, K. Ito, J. Lin, Y. Song, Optimizing the Homogeneity and Efficiency of a Solid Oxide Electrolysis Cell Based on Multiphysics Simulation and Data-driven Surrogate Model, Journal of Power Sources, 562 (2023) 232760. https://doi.org/10.1016/j.jpowsour.2023.232760.

  • Evaluation of the Electrode Characteristics in a Pressurized Solid Oxide Fuel Cell for Electric Aircraft Propulsion

    by Takumi Matsuda, Shuya Wada, Hironori Nakajima, Keiichi Okai, Takayuki Kojima

    This study investigates the characteristics of a pressurized solid oxide fuel cell (SOFC) for a hybrid electric propulsion system in aircraft, which combines gas turbine (jet engine) electric power generation with SOFC operation1)2). The cathode (air electrode) and anode (hydrogen electrode) are electrochemically characterized by evaluating the dependence of exchange current densities on air and hydrogen partial pressures, respectively. Symmetrical tubular electrolyte-supported cells using yttria-stabilized zirconia (YSZ) were prepared to measure the single-electrode reaction resistances of the cathode (Lanthanum Strontium Manganite (LSM)/YSZ) and anode (Ni/YSZ) with electrochemical impedance spectroscopy (EIS). These measurements yield exchange current densities of the cathode and anode independently, which are essential electrochemical kinetic parameters for modeling the respective electrodes in a numerical simulation of a cell3). Such simulations are crucial for optimizing the design and operating conditions of SOFC cells and stacks. Acknowledgments Thanks are offered to Professor Kohei Ito and Associate Professor Tatsumi Kitahara of Kyushu University for their valuable discussions. References 1) K. Okai, H. Nomura, T. Tagashira, A. Nishizawa, Effects of Fuel Type on Aircraft Electric Propulsion with SOFC/GT Hybrid Core, in: 53rd AIAA/SAE/ASEE Joint Propulsion Conference, American Institute of Aeronautics and Astronautics, Reston, Virginia, 2017. https://doi.org/10.2514/6.2017-4957. 2) T. Kojima, K. Okai, Investigation of Weight and Flight-Path Constraints on Liquid Hydrogen Fueled SOFC/GT Hybrid Propulsion System, in: AIAA SCITECH 2023 Forum, American Institute of Aeronautics and Astronautics, Reston, Virginia, 2023. https://doi.org/10.2514/6.2023-1325. 3) H. Nakajima, J. Yamashita, K. Okai, T. Kojima, Numerical Modeling of a Pressurized Solid Oxide Fuel Cell for Electric Aircraft, ECS Meeting Abstract MA2023-01 (2023) 2726–2726. https://doi.org/10.1149/MA2023-01562726mtgabs.

  • Three-Dimensional Numerical Modeling of a Pressurized Solid Oxide Fuel Cell for Electric Aircraft Propulsion Systems Using Kinetic Parameters Determined By Impedance Spectroscopy

    by Hironori Nakajima, Shuya Wada, Takumi Matsuda, Keiichi Okai, Takayuki Kojima

    We focus on the design of a pressurized solid oxide fuel cell integrated into a hybrid electric power generation system with a gas turbine (GT) (jet engine), aimed at propelling electric aircraft1)2). Compared to conventional aircraft, distributed propulsion with electric motors is expected to enhance the propulsion system efficiency. We have thus developed a three-dimensional numerical model of a planar SOFC pressurized for the combination with a GT for the optimal design and operation of practical cells and stacks3). A software package with the finite element method (COMSOL Multiphysics) is employed to analyze the current and temperature distributions in a cell. Exchange current densities for the anode and cathode under pressurized conditions are experimentally evaluated using an electrolyte-supported (YSZ) symmetrical tubular test cell for the electrochemical kinetics in the model by using impedance spectroscopy. Acknowledgments Thanks are offered to Professor Kohei Ito and Associate Professor Tatsumi Kitahara of Kyushu University for their valuable discussions. References 1) T. Kojima, K. Okai, T. Tagashira, Y. Fukuyama, Experimental Study on SOFC/GT Hybrid Engine for Liquid Hydrogen Fueled Electric Propulsion System, in: AIAA Aviat. 2023 Forum, American Institute of Aeronautics and Astronautics, Reston, Virginia, 2023. https://doi.org/10.2514/6.2023-3989. 2) K. Okai, T. Himeno, T. Watanabe, H. Nomura, T. Tagashira, A. Nishizawa, Potential of Aircraft Electric Propulsion with SOFC/GT Hybrid Core, in: 52nd AIAA/SAE/ASEE Jt. Propuls. Conf., American Institute of Aeronautics and Astronautics, Reston, Virginia, 2016. https://doi.org/10.2514/6.2016-4713. 3) H. Nakajima, J. Yamashita, K. Okai, T. Kojima, Numerical Modeling of a Pressurized Solid Oxide Fuel Cell for Electric Aircraft, ECS Meeting Abstract MA2023-01 (2023) 2726–2726. https://doi.org/10.1149/MA2023-01562726mtgabs.

  • Influence of Light Irradiation on Methanol Steam Reforming over Cu/ZnO Nanowire Catalysts

    by Kento Kobayashi, Hironori Nakajima

    Cu/ZnO nanowire (NW) catalysts for methanol steam reforming have been developed to supply hydrogen for fuel cells1). Methanol steam reforming occurs at 200–300°C with the NW catalysts as conventional nanoparticle catalysts and can utilize heat sources2) such as solar energy. The nanowires are expected to exhibit greater durability than conventional nanoparticle catalysts due to their microstructure, which helps prevent aggregation. In this study, we aim to additionally harness sunlight and evaluated the effect of light irradiation on the NW catalysts. The NW catalysts were prepared by hydrothermal synthesis of ZnO nanowires with lengthwise growth (LG) mode and branched growth (BG) mode followed by CuO coating through thermal decomposition of aqueous copper nitrate solutions. Reforming tests under light irradiation at 300°C demonstrated an enhanced methanol conversion rate, which is found to follow the order: Mercury-Xenon lamp (UV light) > Xenon lamp (simulated solar light) > no light irradiation. In the LG mode, the influence of the simulated solar light was minimal, whereas in the BG mode, a localized surface plasmon resonance (LSPR) effect—enhanced by nanowire branching—was possibly observed with the simulated solar light. Increasing the overcrowding density of nanowires led to a decrease in methanol conversion rate but enhanced LSPR activity. These nanowire catalysts demonstrated effective light absorption from UV (LG, BG modes) to visible light (BG mode), and the balance between UV and visible light utilization can be designed by controlling LG/BG modes and nanowire density. The findings provide a useful guideline for the rational design of catalysts for efficient solar-driven methanol reforming. Acknowledgments Thanks are offered to Professor Kohei Ito and Associate Professor Tatsumi Kitahara of Kyushu University for their valuable discussions. References 1) H. Nakajima, D. Lee, M. Lee, C.P. Grigoropoulos, Hydrogen production with CuO / ZnO Nanowire Catalyst for a Nanocatalytic Solar Thermal Steam-Methanol Reformer, International Journal of Hydrogen Energy (2016) 2–6. https://doi.org/10.1016/j.ijhydene.2016.07.039. 2) E. Matsumoto, H. Nakajima, D. Lee, M.-T. Lee, C. P. Grigoropoulos, Methanol Steam Reforming with Hierarchical ZnO/CuO Nanowire Catalysts, The Proceedings of the Thermal Engineering Conference 2021 (2021) 0085. https://doi.org/10.1299/jsmeted.2021.0085.

  • Water Permeability and Oxygen Transport Resistance of Hydrophilic and Hydrophobic Composite Microporous Layer Coated Gas Diffusion Layer

    by Peng Wang, Hironori Nakajima, Tatsumi Kitahara

    Water management is vital to enhance the performance of polymer electrolyte fuel cells (PEFCs). Previously, a hydrophilic and hydrophobic composite microporous layer (MPL) coated gas diffusion layer (GDL) was developed to promote robustness to humidity. It was proved that the composite MPL containing hydrophilic and hydrophobic pores in the same layer was effective in reducing the oxygen transport resistance from measured limiting current density under conditions of the cell temperature of 35°C, supplied gas relative humidity of 200% and flow rate of 1000 cm3 min-1. However, directly distinguishing the hydrophobic and hydrophilic microporous structures in the composite MPL is difficult. In this study, we try to clarify the ratio of hydrophobicity and hydrophilicity contributed to liquid water distribution and oxygen transport resistance. The water permeability test across hydrophilic, hydrophobic, and composite MPLs established the relationship between water flow rates under varying pressure conditions. The water breakthrough pressure obtained with the composite MPL was similar to that obtained with hydrophilic MPL. The composite MPL demonstrated two different rising slopes of the water flow rate. The hydrophilic pores caused the initial slope, which followed the tendency of hydrophilic MPL because water could readily pass through the hydrophilic pores. The following slope changed when the water supply pressure was high enough to pass the hydrophobic pores, and the slope was close to the pure hydrophobic MPL. The water flow rate obtained with the composite MPL was much higher than that obtained with the hydrophobic MPL. Based on the water permeability characteristics, it is considered that the hydrophobic and hydrophilic pores were separately generated in the composite MPL. To further clarify the contribution of hydrophobicity and hydrophilicity ratio to water transport, liquid water flow rate values for MPLs were derived from Darcy's law to fit the water permeability test data under identical pressure. According to the fitting results, a composition comprising 4% hydrophilicity and 96% hydrophobicity was determined to yield results consistent with the water permeability test, in which the actual composite MPL possessed 10 mass% PVDF, 7.5 mass% Nafion, 2.5 mass% TiO2 and 80 mass% carbon black. Based on this ratio, the Leverett function was employed to assess the distribution of liquid water saturation within hydrophobic, hydrophilic, and composite MPLs. In the composite MPL, liquid water saturation reached higher levels from the substrate to the hydrophilic pores in the MPL and almost remained constant from the MPL to the MPL/catalyst layer (CL) interface, indicating that the hydrophilic pores were utilized as water transport pathways. Conversely, hydrophobic pores in the MPL were not fully saturated, leaving most pores empty for gas transport. This balanced configuration of hydrophilicity and hydrophobicity substantially reduced the oxygen transport resistance. An additional assessment of the properties ratio was conducted, assuming that the cell operating current density was 3 A cm-2 and the water flow generated in the reaction was obtained. Under the same water flow rate conditions, increasing the hydrophilicity ratio from 0% to 4% resulted in decreased oxygen transport resistance, attributed to a reduction in water breakthrough pressure at the interface between the MPL and CL, facilitated the expelling of liquid water at the MPL/CL interface more effectively compared with a conventional hydrophobic MPL. However, further elevating the hydrophilicity ratio from 4% to 30% resulted in lower water breakthrough pressure but higher water saturation within the MPL. The saturated MPL possessed fewer pathways for gas transport, raising the oxygen transport resistance. Therefore, the inappropriate hydrophilicity and hydrophobicity ratio disrupted the optimal water-gas equilibrium, causing increased oxygen transport resistance. Through a comparative analysis of experimental and calculated data, the optimal formulation emerges, comprising 10 mass% PVDF, 7.5 mass% Nafion, 2.5 mass% TiO2, and 80 mass% carbon black, delineating hydrophilicity and hydrophobicity ratios of 4% and 96%, respectively.

  • Numerical Modeling of Water Transport in a Microporous Layer-Coated Porous Transport Layer for a Polymer Electrolyte Membrane Water Electrolyzer with an Interdigitated Flow Field for Internal Gas-Liquid Separation

    by Hironori Nakajima, Linda Bolay, Henrik Ekström, Asuka Shima, Göran Lindbergh, Yoshitsugu Sone

    We have developed a novel interdigitated flow field for polymer electrolyte membrane electrolyzers (proton exchange membrane water electrolysis cells) for ground and space applications1),2), which are supposed to work in a hybrid system with a low temperature Sabatier reactor for effective use of heat3),4). This design separates the oxygen and liquid water inside the anode of the cell. It dispenses with water circulators and external separators that use natural or centrifugal buoyancy. To date, we have developed a numerical model for optimizing cell structures. Finite element modeling (COMSOL Multiphysics) of water transport is three-dimensionally conducted for the anode porous transport layer coated with a hydrophobic microporous layer (MPL) (SIGRACET 29BC, SGL Carbon Inc.) assembled with the interdigitated flow field. The MPL can separate the evolved oxygen gas and pressurized liquid water owing to capillary pressure5). The electrochemical kinetic parameters for the model are determined using electrochemical impedance spectra. We model the current densities and the current ratio between the reactant liquid water and water vapor at the interface between the MPL and catalyst layer (CL)6). The model involves the fractional bubble coverage of the produced oxygen gas at the CL, as well as liquid water saturation and liquid water permeability in the MPL7). The vapor evaporating from the liquid water in the MPL is assumed to be mixed with the evolved oxygen for diffusive water transport. The volumetric evaporation rate was estimated from experimental data8). Acknowledgement This study is based on results obtained from a project, JPNP21014, commissioned by the New Energy and Industrial Technology Development (NEDO). References 1) Y. SONE, O.S. HERNANDEZ-MENDOZA, A. SHIMA, M. SATO, H. NAKAJIMA, and H. MATSUMOTO, Water Electrolysis by the Direct Water Supply to the Solid Polymer Electrolyte through the Interdigitated Structure of the Electrode, Electrochemistry, 89 (2021) 138–140. https://doi.org/10.5796/electrochemistry.20-00145. 2) H. NAKAJIMA, V. VEDIYAPPAN, H. MATSUMOTO, M. SATO, O.S. MENDOZA-HERNANDEZ, A. SHIMA, and Y. SONE, Water Transport Analysis in a Polymer Electrolyte Electrolysis Cell Comprised of Gas/Liquid Separating Interdigitated Flow Fields, Electrochemistry, 90 (2022) 017002. https://doi.org/10.5796/electrochemistry.21-00097 3) H. NAKAJIMA, A. SHIMA, M. INOUE, T. ABE, H. MATSUMOTO, O.S. MENDOZA-HERNANDEZ, and Y. SONE, Three-Dimensional Numerical Modeling of a Low-Temperature Sabatier Reactor for a Tandem System of CO2 Methanation and Polymer Electrolyte Membrane Water Electrolysis, Electrochemistry, 90 (2022) 22–00035. https://doi.org/10.5796/electrochemistry.22-00035 4) A. Shima, M. Sakurai, Y. Sone, H. Nakajima, M. Inoue, and T. Abe, Development of CO2 Reduction-Water Electrolysis Tandem Device as a Full-Scale Model, in: 52nd Int. Conf. Environ. Syst., 2023: ICES-2023-196. https://hdl.handle.net/2346/89622 5) H. Nakajima, S. Iwasaki, and T. Kitahara, Pore network modeling of a microporous layer for polymer electrolyte fuel cells under wet conditions, J. Power Sources, 560 (2023) 232677. https://doi.org/10.1016/j.jpowsour.2023.232677 6) H. Nakajima, H. Ekström, A. Shima, Y. Sone, and G. Lindbergh, Water Transport Modeling in a Microporous Layer for a Polymer Electrolyte Membrane Water Electrolyzer Having a Gas-Liquid Separating Interdigitated Flow Field, ECS Transactions, 112 (4) (2023) 273–281. https://doi.org/10.1149/11204.0273ecst 7) S. Kubota, H. Nakajima, M. Sato, A. Shima, M. Sakurai, and Y. Sone, Liquid Water Permeability in a Hydrophobic Microporous Layer for the Anode Interdigitated Flow Field of a Gas-Liquid Separating Polymer Electrolyte Membrane Water Electrolyzer, ECS Transactions, 112 (4) (2023) 207-214. https://doi.org/10.1149/11204.0207ecst 8) P. Wang, H. Nakajima, and T. Kitahara, Effect of Hydrophilic Layer in Double Microporous Layer Coated Gas Diffusion Layer on Performance of a Polymer Electrolyte Fuel Cell, J. Electrochem. Soc., 170 (2023) 124514. https://doi.org/10.1149/1945-7111/ad13da

  • Numerical Modeling of a Polymer Electrolyte Membrane Fuel Cell for Electric Aircraft Propulsion

    by Haruya Oka, Yusaku Katsuki, Hironori Nakajima, Chihiro Inoue

    Electrified propulsion systems with hydrogen-fueled fuel cells can potentially reduce carbon dioxide emissions from aircraft. However, achieving a substantial increase in the gravimetric/volumetric power density of fuel cell systems poses a considerable challenge. In this study, we focus on polymer electrolyte membrane fuel cells (PEMFCs) working between 100 and 200°C. To design an optimized PEMFC structure for an electric aircraft, we have developed a numerical model that employs the finite element method (FEM) (COMSOL Multiphysics) to couple electrochemistry, gas diffusive and convective transports, and heat transfer in fuel cell components such as separators, gas flow channels, gas diffusion layers, catalyst layers, and a PEM1)2). We thereby three-dimensionally visualized the current, hydrogen, oxygen, and water vapor concentration distributions, as well as the temperature distributions, assuming conditions in aircraft operations. Moreover, we developed a machine learning model from the data outputs of the FEM model, which serves as training data, to reduce the computational costs for the fuel cell stack design incorporated in a system-level numerical model. Acknowledgement This study is based on results obtained from a project, JPNP14004, commissioned by the New Energy and Industrial Technology Development (NEDO). We are indepted to Boeing Research & Technology, Boeing Japan for their support and discussions. We are also grateful to Professor Motoaki Kawase of Kyoto University for his fruitful suggestions. Thanks are offered to Professor Kohei Ito and Associate Professor Tatsumi Kitahara of Kyushu University for their valuable discussions. References 1) Ö. Aydın, T. Ochiai, H. Nakajima, T. Kitahara, K. Ito, Y. Ogura, J. Shimano, Mass transport limitation in inlet periphery of fuel cells: Studied on a planar Solid Oxide Fuel Cell, Int. J. Hydrogen Energy, 43 (2018) 17420–17430. https://doi.org/10.1016/j.ijhydene.2018.07.030 2) X. Wang, H. Nakajima, Y. Iwanaga, K. Ito, Numerical and experimental investigation of a cathode-supported microtubular solid oxide electrolysis cell from current and temperature variations in-situ assessed with electrode-segmentation method, J. Energy Storage, 72 (2023) 108459. https://doi.org/10.1016/j.est.2023.108459