William J. Doucette
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
William J. Doucette has a total of 104 co-authors. Here are the top co-authors by number of shared publications:
Bruce Bugbee
Utah Water Research Laboratory, Utah State University, 8200 Old Main Hill, Logan, Utah 84322-8200, United States
6 shared publicationsAnders W. Andren
5 shared publicationsJulie K. Chard
Utah State University, Utah Water Research Laboratory, 8200 Old Main Hill, Logan, Utah 84322-8200, and Environmental Management Division, Hill Air Force Base, Utah
5 shared publicationsRonald C. Sims
Utah State University , Logan , Utah , USA
4 shared publications- Jon A. Arnot
ARC Arnot Research & Consulting, Toronto, Ontario, Canada
3 shared publications Kyle Gorder
Technology Insertion and Innovation Branch, Hill Air Force Base, UT, USA
3 shared publications
Latest Publications
- 1 March 2023
- Published by Oxford University Press (OUP) in Environmental Toxicology and Chemistry
- Vol. 42 (3) , 655-662
Quantifying the Root-to-Shoot Transfer of 4,4ʹ-Methylenedianiline Using Pressure Chamber and Intact Plant Methods
The high-production-volume chemical 4,4ʹ-methylenedianiline (4,4ʹ-MDA) is an aromatic amine used to manufacture 4,4ʹ-methylenedianiline diisocyanate for polyurethane production. Based on 4,4ʹ-MDA's octanol/water partition coefficient (KOW) and correlations with the transpiration stream concentration factor (TSCF), significant plant uptake and root-to-shoot transfer are predicted. However, most correlations between KOW and TSCF were developed for neutral organics and may not be applicable for ionizable bases such as 4,4ʹ-MDA. To investigate, TSCF values for 4,4ʹ-MDA were measured using pressure chamber and intact plant approaches for tomato, soybean, and wheat (intact plants only). 14C-labeled 4,4'-MDA was used to increase analytical sensitivity and facilitate measurement of distribution within plant tissues. The TSCF of 14C-MDA determined using the pressure chamber method was 0.04 ± 0.00 for tomato and 0.17 ± 0.10 for soybean. These values were lower than predicted from log KOW and within the range of values for 14C-pyrene also measured in our study (0.14 ± 0.00 for tomato and 0.16 ± 0.09 for soybean). The TSCF values calculated from measurements made from intact plants grown to maturity were statistically equivalent to those obtained from the pressure chamber method for soybean and tomato. The distributions of 14C within the three plants species were similar, with the roots > leaves ≈ stems > fruit. The log root concentration factors for 4,4ʹ-MDA ranged from 3.68 to 4.33 for the three plant species. This finding indicates that the aromatic amine sorption to root materials is much greater than would be predicted based on its log KOW and may be the reason for the limited root-to-shoot transfer observed in the pressure chamber and intact plant studies. Environ Toxicol Chem 2023;42:655–662. © 2023 SETAC
- 1 March 2023
- Published by Oxford University Press (OUP) in Environmental Toxicology and Chemistry
- Vol. 42 (3) , 655-662
Quantifying the Root-to-Shoot Transfer of 4,4ʹ-Methylenedianiline Using Pressure Chamber and Intact Plant Methods
The high-production-volume chemical 4,4ʹ-methylenedianiline (4,4ʹ-MDA) is an aromatic amine used to manufacture 4,4ʹ-methylenedianiline diisocyanate for polyurethane production. Based on 4,4ʹ-MDA's octanol/water partition coefficient (KOW) and correlations with the transpiration stream concentration factor (TSCF), significant plant uptake and root-to-shoot transfer are predicted. However, most correlations between KOW and TSCF were developed for neutral organics and may not be applicable for ionizable bases such as 4,4ʹ-MDA. To investigate, TSCF values for 4,4ʹ-MDA were measured using pressure chamber and intact plant approaches for tomato, soybean, and wheat (intact plants only). 14C-labeled 4,4'-MDA was used to increase analytical sensitivity and facilitate measurement of distribution within plant tissues. The TSCF of 14C-MDA determined using the pressure chamber method was 0.04 ± 0.00 for tomato and 0.17 ± 0.10 for soybean. These values were lower than predicted from log KOW and within the range of values for 14C-pyrene also measured in our study (0.14 ± 0.00 for tomato and 0.16 ± 0.09 for soybean). The TSCF values calculated from measurements made from intact plants grown to maturity were statistically equivalent to those obtained from the pressure chamber method for soybean and tomato. The distributions of 14C within the three plants species were similar, with the roots > leaves ≈ stems > fruit. The log root concentration factors for 4,4ʹ-MDA ranged from 3.68 to 4.33 for the three plant species. This finding indicates that the aromatic amine sorption to root materials is much greater than would be predicted based on its log KOW and may be the reason for the limited root-to-shoot transfer observed in the pressure chamber and intact plant studies. Environ Toxicol Chem 2023;42:655–662. © 2023 SETAC
- 3 July 2018
- Published by Taylor & Francis in Environmental Forensics
- Vol. 19 (3) , 185-190
Emission rates of chlorinated volatile organics from new and used consumer products found during vapor intrusion investigations: Impact on indoor air concentrations
Consumer products can emit chlorinated volatile organic compounds (CVOCs) that complicate vapor intrusion (VI) assessments. Assessment protocols acknowledge the need to remove these products during VI investigations, but they can be problematic to identify and locate. Predicting if the products cause detectable air concentrations is also difficult since emission rate information is limited and can vary with product use and age. In this study, the emission rates of 1,2-dichloroethane, trichloroethene, tetrachloroethene, and carbon tetrachloride from four consumer products identified as indoor sources during VI field investigations were measured under laboratory conditions using a flow through system. Emissions of PCE from an adhesive container tube ranged from 1.33 ± 1.13 μg/min (unopened) to 23.9 ± 2.93 μg/min (previously opened). The laboratory-measured emission rates were used to estimate indoor air concentrations, which were then compared to concentrations measured after the products placed were into an actual residence. The estimated and measured indoor air concentrations were generally comparable, showing that emission rate information can be used to determine the relative impact of internal CVOC sources.
- 3 July 2018
- Published by Taylor & Francis in Environmental Forensics
- Vol. 19 (3) , 185-190
Emission rates of chlorinated volatile organics from new and used consumer products found during vapor intrusion investigations: Impact on indoor air concentrations
Consumer products can emit chlorinated volatile organic compounds (CVOCs) that complicate vapor intrusion (VI) assessments. Assessment protocols acknowledge the need to remove these products during VI investigations, but they can be problematic to identify and locate. Predicting if the products cause detectable air concentrations is also difficult since emission rate information is limited and can vary with product use and age. In this study, the emission rates of 1,2-dichloroethane, trichloroethene, tetrachloroethene, and carbon tetrachloride from four consumer products identified as indoor sources during VI field investigations were measured under laboratory conditions using a flow through system. Emissions of PCE from an adhesive container tube ranged from 1.33 ± 1.13 μg/min (unopened) to 23.9 ± 2.93 μg/min (previously opened). The laboratory-measured emission rates were used to estimate indoor air concentrations, which were then compared to concentrations measured after the products placed were into an actual residence. The estimated and measured indoor air concentrations were generally comparable, showing that emission rate information can be used to determine the relative impact of internal CVOC sources.
- 1 December 2017
- Published by Elsevier in Science of The Total Environment
- Vol. 601-602, 770-775
The sky is falling III: The effect of deposition from static solid rocket motor tests on juvenile crops
- 1 December 2017
- Published by Elsevier in Science of The Total Environment
- Vol. 601-602, 770-775
The sky is falling III: The effect of deposition from static solid rocket motor tests on juvenile crops
- 4 October 2017
- Published by Oxford University Press (OUP) in Environmental Toxicology and Chemistry
- Vol. 37 (1) , 21-33
A review of measured bioaccumulation data on terrestrial plants for organic chemicals: Metrics, variability, and the need for standardized measurement protocols
Quantifying the transfer of organic chemicals from the environment into terrestrial plants is essential for assessing human and ecological risks, using plants as environmental contamination biomonitors, and predicting phytoremediation effectiveness. Experimental data describing chemical uptake by plants are often expressed as ratios of chemical concentrations in the plant compartments of interest (e.g., leaves, shoots, roots, xylem sap) to those in the exposure medium (e.g., soil, soil porewater, hydroponic solution, air). These ratios are generally referred to as “bioconcentration factors” but have also been named for the specific plant compartment sampled, such as “root concentration factors,” “leaf concentration factors,” or “transpiration stream (xylem sap) concentrations factors.” We reviewed over 350 articles to develop a database with 7049 entries of measured bioaccumulation data for 310 organic chemicals and 112 terrestrial plant species. Various experimental approaches have been used; therefore, interstudy comparisons and data-quality evaluations are difficult. Key exposure and plant growth conditions were often missing, and units were often unclear or not reported. The lack of comparable high-confidence data also limits model evaluation and development. Standard test protocols or, at a minimum, standard reporting guidelines for the measurement of plant uptake data are recommended to generate comparable, high-quality data that will improve mechanistic understanding of organic chemical uptake by plants. Environ Toxicol Chem 2017;9999:1–13. © 2017 SETAC
- 4 October 2017
- Published by Oxford University Press (OUP) in Environmental Toxicology and Chemistry
- Vol. 37 (1) , 21-33
A review of measured bioaccumulation data on terrestrial plants for organic chemicals: Metrics, variability, and the need for standardized measurement protocols
Quantifying the transfer of organic chemicals from the environment into terrestrial plants is essential for assessing human and ecological risks, using plants as environmental contamination biomonitors, and predicting phytoremediation effectiveness. Experimental data describing chemical uptake by plants are often expressed as ratios of chemical concentrations in the plant compartments of interest (e.g., leaves, shoots, roots, xylem sap) to those in the exposure medium (e.g., soil, soil porewater, hydroponic solution, air). These ratios are generally referred to as “bioconcentration factors” but have also been named for the specific plant compartment sampled, such as “root concentration factors,” “leaf concentration factors,” or “transpiration stream (xylem sap) concentrations factors.” We reviewed over 350 articles to develop a database with 7049 entries of measured bioaccumulation data for 310 organic chemicals and 112 terrestrial plant species. Various experimental approaches have been used; therefore, interstudy comparisons and data-quality evaluations are difficult. Key exposure and plant growth conditions were often missing, and units were often unclear or not reported. The lack of comparable high-confidence data also limits model evaluation and development. Standard test protocols or, at a minimum, standard reporting guidelines for the measurement of plant uptake data are recommended to generate comparable, high-quality data that will improve mechanistic understanding of organic chemical uptake by plants. Environ Toxicol Chem 2017;9999:1–13. © 2017 SETAC
- Open Access
- 1 October 2016
- Published by Elsevier in Journal of Environmental Management
- Vol. 181, 374-384
Improving plant bioaccumulation science through consistent reporting of experimental data
- 1 October 2016
- Published by Elsevier in Journal of Environmental Management
- Vol. 181, 374-384
Open AccessImproving plant bioaccumulation science through consistent reporting of experimental data
- Open Access
- 1 August 2015
- Published by Oxford University Press (OUP) in Integrated Environmental Assessment and Management
- Vol. 12 (1) , 123-134
Review of existing terrestrial bioaccumulation models and terrestrial bioaccumulation modeling needs for organic chemicals
Protocols for terrestrial bioaccumulation assessments are far less-developed than for aquatic systems. This article reviews modeling approaches that can be used to assess the terrestrial bioaccumulation potential of commercial organic chemicals. Models exist for plant, invertebrate, mammal, and avian species and for entire terrestrial food webs, including some that consider spatial factors. Limitations and gaps in terrestrial bioaccumulation modeling include the lack of QSARs for biotransformation and dietary assimilation efficiencies for terrestrial species; the lack of models and QSARs for important terrestrial species such as insects, amphibians and reptiles; the lack of standardized testing protocols for plants with limited development of plant models; and the limited chemical domain of existing bioaccumulation models and QSARs (e.g., primarily applicable to nonionic organic chemicals). There is an urgent need for high-quality field data sets for validating models and assessing their performance. There is a need to improve coordination among laboratory, field, and modeling efforts on bioaccumulative substances in order to improve the state of the science for challenging substances. Integr Environ Assess Manag 2016;12:123–134. © 2015 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of SETAC. Key Points The report reviews models available for assessing the bioaccumulation potential of organic compounds in terrestrial food webs. Major limitations in terrestrial bioaccumulation modeling include the lack of QSARs for biotransformation and dietary assimilation efficiencies for terrestrial species, and the lack of models and QSARs for important terrestrial species such as insects, amphibians and reptiles. Other limitations include the limited chemical domain of existing bioaccumulation models and QSARs, and the lack of standardized testing protocols for plants that has limited development of plant models.
- 1 August 2015
- Published by Oxford University Press (OUP) in Integrated Environmental Assessment and Management
- Vol. 12 (1) , 123-134
Open AccessReview of existing terrestrial bioaccumulation models and terrestrial bioaccumulation modeling needs for organic chemicals
Protocols for terrestrial bioaccumulation assessments are far less-developed than for aquatic systems. This article reviews modeling approaches that can be used to assess the terrestrial bioaccumulation potential of commercial organic chemicals. Models exist for plant, invertebrate, mammal, and avian species and for entire terrestrial food webs, including some that consider spatial factors. Limitations and gaps in terrestrial bioaccumulation modeling include the lack of QSARs for biotransformation and dietary assimilation efficiencies for terrestrial species; the lack of models and QSARs for important terrestrial species such as insects, amphibians and reptiles; the lack of standardized testing protocols for plants with limited development of plant models; and the limited chemical domain of existing bioaccumulation models and QSARs (e.g., primarily applicable to nonionic organic chemicals). There is an urgent need for high-quality field data sets for validating models and assessing their performance. There is a need to improve coordination among laboratory, field, and modeling efforts on bioaccumulative substances in order to improve the state of the science for challenging substances. Integr Environ Assess Manag 2016;12:123–134. © 2015 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of SETAC. Key Points The report reviews models available for assessing the bioaccumulation potential of organic compounds in terrestrial food webs. Major limitations in terrestrial bioaccumulation modeling include the lack of QSARs for biotransformation and dietary assimilation efficiencies for terrestrial species, and the lack of models and QSARs for important terrestrial species such as insects, amphibians and reptiles. Other limitations include the limited chemical domain of existing bioaccumulation models and QSARs, and the lack of standardized testing protocols for plants that has limited development of plant models.
- 1 March 2015
- Published by Elsevier in Chemosphere
- Vol. 122, 32-37
Plant leaves as indoor air passive samplers for volatile organic compounds (VOCs)
- 1 March 2015
- Published by Elsevier in Chemosphere
- Vol. 122, 32-37
Plant leaves as indoor air passive samplers for volatile organic compounds (VOCs)
- 1 June 2014
- Published by Elsevier in Science of The Total Environment
- Vol. 482-483, 36-41
The sky is falling II: Impact of deposition produced during the static testing of solid rocket motors on corn and alfalfa
- 1 June 2014
- Published by Elsevier in Science of The Total Environment
- Vol. 482-483, 36-41
The sky is falling II: Impact of deposition produced during the static testing of solid rocket motors on corn and alfalfa
- 8 August 2013
- Published by Oxford University Press (OUP) in Environmental Toxicology and Chemistry
- Vol. 32 (11) , 2478-2481
Root-to-Shoot transfer and distribution of endosulfan in the wetland macrophyte Bidens laevis L.
Endosulfan is genotoxic in somatic cells of Bidens laevis, and reproduction could be affected if translocated from roots to flower buds. Hydroponic experiments were conducted to quantify this transfer. While the root uptake of [14C] endosulfan and its transfer to aboveground tissues was relatively low, the resulting average flower bud concentration (1.01 ± 0.76 ng/g) after 30 d of exposure to an aqueous concentration of 5 μg/L could still represent a genotoxic risk for germ cells. Environ Toxicol Chem 2013;32:2478–2481. © 2013 SETAC
- 8 August 2013
- Published by Oxford University Press (OUP) in Environmental Toxicology and Chemistry
- Vol. 32 (11) , 2478-2481
Root-to-Shoot transfer and distribution of endosulfan in the wetland macrophyte Bidens laevis L.
Endosulfan is genotoxic in somatic cells of Bidens laevis, and reproduction could be affected if translocated from roots to flower buds. Hydroponic experiments were conducted to quantify this transfer. While the root uptake of [14C] endosulfan and its transfer to aboveground tissues was relatively low, the resulting average flower bud concentration (1.01 ± 0.76 ng/g) after 30 d of exposure to an aqueous concentration of 5 μg/L could still represent a genotoxic risk for germ cells. Environ Toxicol Chem 2013;32:2478–2481. © 2013 SETAC