JRJohn W. Rudnicki

John W. Rudnicki

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


John W. Rudnicki has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Reaction‐Driven Crack Propagation Controlled by Vein Extension in a Dilute Fracture System

    by Rui Feng, John Rudnicki

    Permanent mineral trapping of in ultramafic rocks can be accelerated if carbonate precipitation wedges open microcracks and sustains crack growth, thereby increasing permeability and reactive surface area. We develop a vein‐extension controlled model for carbonation reaction‐driven cracking in a dilute fracture system that couples (a) a singular integral equation for crack opening, (b) crystallization pressure‐limited precipitation kinetics for vein thickening, (c) a growth law for the mineralized vein length , and (d) a propagation criterion based on the critical stress intensity factor. The growth law for captures the competition between diffusive supply and reaction rate, reduced when reactant residence time is insufficient for precipitation, providing a minimal representation of the non‐collocated nature of carbonation. Non‐dimensionalization identifies three governing controls: a Damköhler‐type number quantifying the competition between precipitation kinetics and diffusion, a chemical supply strength characterizing solute availability relative to host stiffness, and a normalized fracture toughness. Semi‐analytical solutions reproduce a prolonged initiation stage during which stress intensity builds while crack length remains fixed, followed by stable wedge‐loaded propagation once toughness is reached. Initiation time and onset propagation speed depend nonmonotonically on transport conditions, producing an optimum region (e.g., near Damköhler number for the reference half crack length mm) where initiation time is minimized and propagation rate is maximized. The framework provides quantitative criteria to assess the feasibility of reaction‐induced cracking and to identify mechanisms for accelerating carbonation‐driven cracking in natural and engineered mineralization settings.

  • Open Access

    Effects of Oscillating Pore Pressure of Fluid Injection on Fault Slip Described by Rate and State Friction

    by Micaela Mercuri, John W. Rudnicki

    Injection of pore fluid can substantially affect fault slip, often resulting in seismic activity. We simulate the axisymmetric compression experiments of Noël, Passelégue, et al. (2019), https://doi.org/10.1029/2019jb018517 on a saw‐cut specimen of Fontainebleau sandstone subjected to periodic oscillations of fluid pore pressure. We adopt a simple spring‐block model obeying rate and state frictional sliding. Results depend strongly on , the ratio of the period of pore pressure oscillation to time scale of rate and state effects. For small pore pressure oscillation dominates and simulations with constant rate and state parameters show that peak velocities align with pore pressure peaks but not for every peak. For large rate and state effects dominate: multiple velocity peaks occur for each pore pressure period and velocity peaks can occur near the trough or the peak of pore pressure oscillation. In the experiments, measured values of the rate and state parameters varied with velocity. When this variation is included in the simulations, results are consistent with observations at higher confining stress imposed in the experiments. However, for the lower confining stress, it is necessary to include a dependence of the parameters on the effective normal stress for the simulations to be consistent with the observations. In both cases, the magnitude of velocity peaks increases with pore pressure amplitude but the magnitude is less for the higher confining stress. This is consistent with the fewer number of stick‐slip and acoustic emission events observed in the experiments at higher confining stress.

  • Open Access

    Homogeneous and Membrane Pore Fluid Diffusion in Spring Block Simulations of Fault Slip With Rate and State Friction

    by J. W. Rudnicki, Cheng Mei

    Spring block, and sometimes continuum, models of the effects of the coupling of fluid flow and frictional slip often employ the membrane approximation. This approximation assumes that the fluid flux between the slipping layer and a remote pore fluid reservoir is proportional to the difference between the value of pore pressure in the reservoir and in the slipping zone. In contrast, Darcy's law states that the fluid flux is proportional to the gradient of the pore pressure. We analyze and compare these two formulations by asymptotic analysis of the fluid flow equations and numerical simulations of a spring–block model using rate and state friction. This analysis shows that membrane diffusion agrees with homogeneous diffusion in the limit of undrained conditions and for nearly drained conditions. For homogeneous diffusion and essentially undrained conditions, both the asymptotic analysis and numerical simulations indicate the formation of a boundary layer near the shear zone where gradients of pore pressure are large. Outside this layer the pore pressure rapidly approaches the drained solution. A linearized stability analysis derives the dependence of the non‐dimensional critical stiffness () on fluid diffusivity, dilatancy factor (), and shear zone thickness. The homogeneous and membrane diffusion models exhibit nearly identical in the limits of drained and undrained conditions, but differ between the two limits. In this intermediate range, numerical simulations show that the two models produce similar slip behavior for but significant differences in slip velocity and recurrence patterns for .


  • Open Access

    Effects of Oscillating Pore Pressure of Fluid Injection on Fault Slip Described by Rate and State Friction

    by Micaela Mercuri, John W. Rudnicki

    Injection of pore fluid can substantially affect fault slip, often resulting in seismic activity. We simulate axisymmetric compression experiments on a saw-cut specimen of Fontainebleau sandstone (Noel et al. 2019) subjected to periodic oscillations of pore fluid pressure. We adopt a simple spring-block model obeying rate and state frictional sliding. Results depend strongly on Tp, the ratio of the period of pore pressure oscillation to time scale of rate and state effects. For small Tp pore pressure oscillation dominates and simulations with constant rate and state parameters show that peak velocities align with pore pressure peaks but not for every peak. For large Tp, rate and state effects dominate: simulations show that multiple velocity peaks occur for each pore pressure period and that velocity peaks can occur near the trough or peak of the pore pressure oscillation. In the experiments, measured values of the rate and state parameters varied with velocity. When this variation was included in the simulations, the results are consistent with the observations at the higher confining stress imposed in the experiments. However, for the lower confining stress, it was necessary to include a dependence of the parameters on the effective normal stress for the simulations to be consistent with the observations. In both cases, the magnitude of velocity peaks increases with pore pressure amplitude but the magnitude is less for the higher confining stress. This is consistent with the fewer number of stick-slip and acoustic emission events observed in the experiments at higher confining stress.


  • Open Access

    Coupled Fracture Mechanics‐Geochemical Model of Reaction‐Driven Cracking

    by Rui Feng, Pouyan Asem, John Rudnicki, Emmanuel Detournay

    Reaction‐driven cracking has been discussed for decades. One mechanism is the extension of a microcrack resulting from precipitation. This mechanism can create porosity, permeability and reactive surface area in low‐permeability rock. We model this problem as a fracture loaded over a fraction of its length by a vein. The loading causes crack propagation when the stress intensity factor reaches its critical value. We calculate the conditions for the onset of crack growth, the time required, pressure distribution around the vein, and the crack surface displacements. These results are relevant to many problems. One application is to geological storage of by mineralization. Results depend strongly on rock parameters but using representative values from experiments, our calculations suggest an initiation time within tens of years at low temperature and dilute fluid conditions. Lower critical stress intensity factor, higher reaction rate, and greater carbonate filling ratio reduce the time to initiation.


  • Open Access

    Microphysical Modeling of Fault Slip and Stability Transition in Hydrothermal Conditions

    by Cheng Mei, John W. Rudnicki

    Field and laboratory observations indicate that the frictional behaviors of faults depend on hydrothermal conditions. We extend the microphysical Chen‐Niemeijer‐Spiers (CNS) model to hydrothermal conditions by using the observed temperature variation of indentation hardness to infer the temperature dependence of a microphysical parameter . This parameter is assumed constant in previous versions of the CNS model. A simple spring‐slider system is used to simulate the fault system and investigate the steady‐state frictional behaviors of wet granite gouges. Our numerical results quantitatively reproduce experimental data showing the frictional‐plastic transition. The results also describe the transition from velocity‐strengthening at low temperatures (370°C). In our extended CNS model, these results suggest that the dominant shear deformation mechanism does transition from frictional granular flow to fully plastic creep with increasing temperature.


  • Open Access

    Rate and State Simulation of Two Experiments with Pore Fluid Injection Under Creep Conditions

    by John Rudnicki

    Recent industrial processes that involve injection of fluids, such as geothermal stimulation, disposal of waste water from hydraulic fracturing and carbon sequestration, have induced seismicity that has caused concern and resulted in discontinuation of the activity. Although field observations are the ultimate test of the effects of pore fluid on failure, their interpretation is complicated by heterogeneity of hydrologic and mechanical structure, and pumping and loading history. In particular circumstances, well-designed field tests can overcome some of these limitations. Laboratory experiments, despite their limited size and time scales, provide a more controlled environment that can yield an understanding of fundamental processes. Simple models that simulate the experiments can assess whether the mechanisms included in the models are sufficient to describe well the response or more complex formulations are needed. In addition, simulations can extend results for parameter values and loading programs beyond those achievable in experiments and aid in extrapolation to field applications.This work uses a spring-block model and rate and state friction to simulate experiments conducted in a double direct shear apparatus on simulated carbonate fault gouge (Scuderi et al., EPSL, 2017) and on a shale bearing rock (Scuderi and Collettini, JGR, 2018). Both sets of experiments used the same loading protocol and injected pore fluid under creep conditions. When velocity strengthening rate and state friction is used to simulate the experiments on the simulated carbonate fault gouge the results agree well with the observed onset of tertiary creep in the experiment. Thus, the simulation reinforces the observation that pore fluid injection can induce rapid slip even when the friction relation is velocity strengthening. The rate and state framework provides an interpretation alternative to the standard one of the Mohr's circle moving to the left as pressure increases. In the rate and state framework, the friction coefficient must increase with pore pressure increase. The shale has a very low nominal friction coefficient (0.28) and is much more velocity strengthening than the carbonate. The simulation agrees with the observations that increases in pore pressure induce an increase in slip velocity but the magnitudes reach only about 100 µm/s by the end of the experiment. The simulation predicts reasonably well the times at which representative values of the slip velocity and displacement occur but the overall agreement of simulation and observation is not as good as for the carbonate. Mechanisms other than rate and state friction, for example, direct dependence of the friction coefficient on slip and porosity changes, may be significant.

  • Open Access

    Rate and State Simulation of Two Experiments With Pore Fluid Injection Under Creep Conditions

    by J. W. Rudnicki

    This study uses a spring‐block model and rate and state friction to simulate experiments conducted in a double direct‐shear apparatus on carbonate fault gouge (Scuderi et al., 2017, https://doi.org/10.1016/j.epsl.2017.08.009) and on shale bearing rock (Scuderi & Collettini, 2018, https://doi.org/10.1029/2018jb016084). Both sets of experiments used the same loading protocol and injected pore fluid under creep conditions. When velocity strengthening rate and state friction is used to simulate the experiments on the carbonate fault gouge the results agree well with the observed onset of tertiary creep in the experiment. Thus, the simulation reinforces the observation that pore fluid injection can induce rapid slip even when the friction relation is velocity strengthening. The rate and state framework provides an interpretation alternative to the standard one of the Mohr's circle moving to the left as pressure increases. In the rate and state framework, the friction coefficient must increase with pore pressure increase. The shale has a low nominal friction coefficient (0.28) and is much more velocity strengthening than the carbonate. The simulation agrees with the observations that increases in pore pressure induce an increase in slip velocity but the magnitudes reach only about 100 microns/s by the end of the experiment. The simulation for the shale also agrees well with the magnitude of the observed displacement at the end of the experiment but observed displacement is increasing much more rapidly the calculated. Although the calculations agree well with features of the observations near failure, the overall curves of displacement and velocity are significantly different.