Pobitra Halder
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Pobitra Halder has a total of 98 co-authors. Here are the top co-authors by number of shared publications:
- Kalpit Shah
Australian Research Council Training Centre for the Transformation of Australia’s Biosolids Resource, Royal Melbourne Institute of Technology University, Bundoora, VIC 3083, Australia
10 shared publications - Sazal Kundu
Process Safety and Environment Protection Research Group, School of Engineering, The University of Newcastle, Callaghan, NSW 2308, Australia
9 shared publications - Jorge Paz-Ferreiro
School of Engineering, RMIT University, Melbourne 3000, Australia
7 shared publications Savankumar Patel
7 shared publicationsAravind Surapaneni
6 shared publications- Abul Kalam Azad
School of Engineering and Technology, Central Queensland University, Melbourne, VIC 3000, Australia
5 shared publications
Latest Publications
- Top Cited PapersOpen Access
- 10 May 2024
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 199
Performance, emissions and economic analyses of hydrogen fuel cell vehicles
- 10 May 2024
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 199
Top Cited PapersOpen AccessPerformance, emissions and economic analyses of hydrogen fuel cell vehicles
- Top Cited PapersOpen Access
- 8 August 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 52, 973-1004
Advancements in hydrogen production, storage, distribution and refuelling for a sustainable transport sector: Hydrogen fuel cell vehicles
- 8 August 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 52, 973-1004
Top Cited PapersOpen AccessAdvancements in hydrogen production, storage, distribution and refuelling for a sustainable transport sector: Hydrogen fuel cell vehicles
- 18 July 2023
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 173
Enhancing the pyrolytic conversion of biosolids to value-added products via mild acid pre-treatment
- 18 July 2023
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 173
Enhancing the pyrolytic conversion of biosolids to value-added products via mild acid pre-treatment
- 6 January 2023
- Published by Elsevier in Bioresource Technology
- Vol. 371, 128587
Techno-economic analysis of ionic liquid pre-treatment integrated pyrolysis of biomass for co-production of furfural and levoglucosenone
- 6 January 2023
- Published by Elsevier in Bioresource Technology
- Vol. 371, 128587
Techno-economic analysis of ionic liquid pre-treatment integrated pyrolysis of biomass for co-production of furfural and levoglucosenone
- 26 October 2021
- Published by SAGE Publications in WORK: A Journal of Prevention, Assessment & Rehabilitation
- Vol. 70 (2) , 657-671
Garments furniture design for Bangladeshi workers considering ergonomic principles
BACKGROUND: In Bangladesh, workers typically spend at least eight hours a day at garment factories in sitting and/or standing position. Prolonged sitting on ergonomically unfit furniture causes back, neck, and shoulder pain, which reduces the working efficiency and leading to low productivity. OBJECTIVE: The aim of this study is to design ergonomically correct furniture for Bangladeshi garment workers considering multivariate analysis on the anthropometric data. METHODS: Twelve anthropometric measures and five furniture dimensions were measured. The sample comprised of 600 volunteer workers from different garment industry. The furniture dimensions were compared with the relevant anthropometric characteristics and found a high level of mismatch (e.g. seat height (male 18%, female 94.25%), seat depth (male 96%, female 63.50%), seat width (male 9.50%, female 36.25%), sewing table height (male 56.50%, female 50%), and desk height for inspection, cutting and ironing table (male 100%, female 100%). RESULTS: New design specifications were proposed of the worker which improved the match percentage. The multivariate anthropometric analysis generated 8 cases and for each case the ranges of anthropometric measurements have been identified. CONCLUSION: The results will help to design robust ergonomic garments furniture.
- 26 October 2021
- Published by SAGE Publications in WORK: A Journal of Prevention, Assessment & Rehabilitation
- Vol. 70 (2) , 657-671
Garments furniture design for Bangladeshi workers considering ergonomic principles
BACKGROUND: In Bangladesh, workers typically spend at least eight hours a day at garment factories in sitting and/or standing position. Prolonged sitting on ergonomically unfit furniture causes back, neck, and shoulder pain, which reduces the working efficiency and leading to low productivity. OBJECTIVE: The aim of this study is to design ergonomically correct furniture for Bangladeshi garment workers considering multivariate analysis on the anthropometric data. METHODS: Twelve anthropometric measures and five furniture dimensions were measured. The sample comprised of 600 volunteer workers from different garment industry. The furniture dimensions were compared with the relevant anthropometric characteristics and found a high level of mismatch (e.g. seat height (male 18%, female 94.25%), seat depth (male 96%, female 63.50%), seat width (male 9.50%, female 36.25%), sewing table height (male 56.50%, female 50%), and desk height for inspection, cutting and ironing table (male 100%, female 100%). RESULTS: New design specifications were proposed of the worker which improved the match percentage. The multivariate anthropometric analysis generated 8 cases and for each case the ranges of anthropometric measurements have been identified. CONCLUSION: The results will help to design robust ergonomic garments furniture.
- 16 December 2020
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 7 (3) , 638-649
Removal of PFASs from biosolids using a semi-pilot scale pyrolysis reactor and the application of biosolids derived biochar for the removal of PFASs from contaminated water
This study focuses on the conversion of biosolids to biochar and its further use in adsorbing per- and polyfluoroalkyl substances (PFASs) from contaminated water.
- 16 December 2020
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 7 (3) , 638-649
Removal of PFASs from biosolids using a semi-pilot scale pyrolysis reactor and the application of biosolids derived biochar for the removal of PFASs from contaminated water
This study focuses on the conversion of biosolids to biochar and its further use in adsorbing per- and polyfluoroalkyl substances (PFASs) from contaminated water.
- Open Access
Performance, Emission and Combustion Characteristics of a Diesel Engine Powered by Macadamia and Grapeseed Biodiesels
Biodiesel is an alternative, eco-friendly and renewable source of energy. It can be produced from a wide range of feedstocks which can be grown in marginal land use. It has drawn more attention to the researchers. In this study, the oil extraction, biodiesel conversion, and physiochemical properties of Macadamia (Macadamia integrifolia) and Grapeseed (Vitis vinifera) biodiesels are presented. The experimental investigation of diesel engine performance, emissions and combustion characteristics were conducted using B5 (5% biodiesel and 95% diesel by volume) and B10 (10% biodiesel and 90% diesel by volume) blends. The engine performance parameters, such as brake power (BP), brake specific fuel consumption (BSFC), and brake thermal efficiency (BTE) have been investigated in this experiment. The emission parameters, for example, carbon monoxide (CO), the ratio of CO2/CO, nitrogen oxide (NOx), hydrocarbon (HC), particulate matter (PM) have been measured during the experiment. Finally, the combustion parameters such as cylinder pressure (CP) were recorded, and heat release rate (HRR) was analysed and compared with that of diesel fuel. The study revealed that the Macadamia biodiesel performed better than Grapeseed biodiesel and behaved closely to that of diesel fuel. A significant reduction of engine emissions was found in the case of Macadamia biodiesel with a minimal reduction of engine performance. Further analysis of energy, exergy and tribological characteristics of the Macadamia biodiesel is recommended for assessing its feasibility for commercial application.
Open AccessPerformance, Emission and Combustion Characteristics of a Diesel Engine Powered by Macadamia and Grapeseed Biodiesels
Biodiesel is an alternative, eco-friendly and renewable source of energy. It can be produced from a wide range of feedstocks which can be grown in marginal land use. It has drawn more attention to the researchers. In this study, the oil extraction, biodiesel conversion, and physiochemical properties of Macadamia (Macadamia integrifolia) and Grapeseed (Vitis vinifera) biodiesels are presented. The experimental investigation of diesel engine performance, emissions and combustion characteristics were conducted using B5 (5% biodiesel and 95% diesel by volume) and B10 (10% biodiesel and 90% diesel by volume) blends. The engine performance parameters, such as brake power (BP), brake specific fuel consumption (BSFC), and brake thermal efficiency (BTE) have been investigated in this experiment. The emission parameters, for example, carbon monoxide (CO), the ratio of CO2/CO, nitrogen oxide (NOx), hydrocarbon (HC), particulate matter (PM) have been measured during the experiment. Finally, the combustion parameters such as cylinder pressure (CP) were recorded, and heat release rate (HRR) was analysed and compared with that of diesel fuel. The study revealed that the Macadamia biodiesel performed better than Grapeseed biodiesel and behaved closely to that of diesel fuel. A significant reduction of engine emissions was found in the case of Macadamia biodiesel with a minimal reduction of engine performance. Further analysis of energy, exergy and tribological characteristics of the Macadamia biodiesel is recommended for assessing its feasibility for commercial application.
- 10 December 2019
- Published by Creative Decisions Foundation in International Journal of the Analytic Hierarchy Process
- Vol. 11 (3) , 389-414
CUSTOMER DRIVEN QUALITY IMPROVEMENT OF A SPECIFIC PRODUCT THROUGH AHP AND ENTROPY BASED QFD: A CASE STUDY
Understanding the voice of the customers (VOCs) and properly incorporating their preferences and perceptions into the conceptual design process is the core step of customer-driven product development. To improve customer satisfaction and market profitability, the design team should have a customer-driven quality management and product development system. Quality function deployment (QFD) is an important customer-driven quality management tool that helps identify customer requirements and translate them into proper technical measures. This paper focuses on the application of the AHP and an entropy-based QFD approach on a manufacturing company to improve the quality of its product (blender) and determine the priorities for further improvement. The paper shows how customer requirements can be identified and applied to prioritize the design requirements for improving the quality of a blender. The Analytic Hierarchy Process (AHP) is integrated to determine the final importance of the weights of the customer needs, and entropy is used to determine the set of priority ratings. This integrated framework can help achieve an effective evaluation of the final design solution for product development by overcoming the pitfalls of the traditional QFD approach. An application in a Bangladeshi company that produces blenders is presented to illustrate the performance of the proposed approach.
- 10 December 2019
- Published by Creative Decisions Foundation in International Journal of the Analytic Hierarchy Process
- Vol. 11 (3) , 389-414
CUSTOMER DRIVEN QUALITY IMPROVEMENT OF A SPECIFIC PRODUCT THROUGH AHP AND ENTROPY BASED QFD: A CASE STUDY
Understanding the voice of the customers (VOCs) and properly incorporating their preferences and perceptions into the conceptual design process is the core step of customer-driven product development. To improve customer satisfaction and market profitability, the design team should have a customer-driven quality management and product development system. Quality function deployment (QFD) is an important customer-driven quality management tool that helps identify customer requirements and translate them into proper technical measures. This paper focuses on the application of the AHP and an entropy-based QFD approach on a manufacturing company to improve the quality of its product (blender) and determine the priorities for further improvement. The paper shows how customer requirements can be identified and applied to prioritize the design requirements for improving the quality of a blender. The Analytic Hierarchy Process (AHP) is integrated to determine the final importance of the weights of the customer needs, and entropy is used to determine the set of priority ratings. This integrated framework can help achieve an effective evaluation of the final design solution for product development by overcoming the pitfalls of the traditional QFD approach. An application in a Bangladeshi company that produces blenders is presented to illustrate the performance of the proposed approach.
- 1 November 2019
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 144
Slow pyrolysis of biosolids in a bubbling fluidised bed reactor using biochar, activated char and lime
- 1 November 2019
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 144
Slow pyrolysis of biosolids in a bubbling fluidised bed reactor using biochar, activated char and lime