Arghya Patra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Arghya Patra has a total of 72 co-authors. Here are the top co-authors by number of shared publications:
- Beniamin Zahiri
Department of Materials Science and Engineering, University of Illinois Urbana-Champaign, Urbana, USA
13 shared publications Paul V. Braun
Department of Materials Science and Engineering
10 shared publicationsSrijan Sengupta
7 shared publicationsKarabi Das
6 shared publicationsPaul V Braun
University of Illinois at Urbana-Champaign
5 shared publications- Paul V. Braun
Department of Materials Science and Engineering
5 shared publications
Latest Publications
- Open Access
- 2 November 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Revealing the role of Li content on the structural stability of textured LiCoO 2 battery electrodes along fast diffusing directions
Facile ion transport in layered battery cathode systems require (11x) terminating facets. However, the facets that provide accelerated transport also amplify deleterious phase transitions and chemical reactions. The coupling between initial intercalant ion content (nominal lithium-ion stoichiometry), ionic mobility and phase transformations along the fastest diffusing facets remain understudied. Here, the coupling is elucidated using electrodeposited highly textured ||(sample normal direction, ND) LiCoO2 (LCO) electrodes with controlled texture, facet presentation, and initial lithium content. Contrary to powdered systems with untextured particles, here we show that minute variations in lithium content drive distinct interphase formation at (110) terminating facets and impact ion diffusivity in cathodes possessing identical IIND texture, indicating the unique importance of control of lithium content in highly oriented systems. While Lithium-poor IIND LCO cathodes provide initial good ion diffusivity, they exhibit accelerated interfacially originated degradation along directions via rapid rocksalt formation. Lithium-rich IIND LCO electrodes exhibit elevated interfacial degradation due to the poorly conducting Li2CO3 on the surface. Lithium-balanced textured LCO electrodes suppress kinetically driven degradation pathways, even at (110) terminating facets, and provide both good ion diffusivity and structural stability. The dual control of lithium content and crystallographic orientation along the fastest diffusing directions provided by the textured electrodeposited cathodes enables deterministic design of energy-dense cathodes with good ion transport kinetics and low surface reactivity, both in thin and thick electrode formats, a combination which is difficult to achieve in untextured slurry systems presenting a range of surface facets.
- 2 November 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessRevealing the role of Li content on the structural stability of textured LiCoO 2 battery electrodes along fast diffusing directions
Facile ion transport in layered battery cathode systems require (11x) terminating facets. However, the facets that provide accelerated transport also amplify deleterious phase transitions and chemical reactions. The coupling between initial intercalant ion content (nominal lithium-ion stoichiometry), ionic mobility and phase transformations along the fastest diffusing facets remain understudied. Here, the coupling is elucidated using electrodeposited highly textured ||(sample normal direction, ND) LiCoO2 (LCO) electrodes with controlled texture, facet presentation, and initial lithium content. Contrary to powdered systems with untextured particles, here we show that minute variations in lithium content drive distinct interphase formation at (110) terminating facets and impact ion diffusivity in cathodes possessing identical IIND texture, indicating the unique importance of control of lithium content in highly oriented systems. While Lithium-poor IIND LCO cathodes provide initial good ion diffusivity, they exhibit accelerated interfacially originated degradation along directions via rapid rocksalt formation. Lithium-rich IIND LCO electrodes exhibit elevated interfacial degradation due to the poorly conducting Li2CO3 on the surface. Lithium-balanced textured LCO electrodes suppress kinetically driven degradation pathways, even at (110) terminating facets, and provide both good ion diffusivity and structural stability. The dual control of lithium content and crystallographic orientation along the fastest diffusing directions provided by the textured electrodeposited cathodes enables deterministic design of energy-dense cathodes with good ion transport kinetics and low surface reactivity, both in thin and thick electrode formats, a combination which is difficult to achieve in untextured slurry systems presenting a range of surface facets.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (26) , 1367
An All-Electrodeposited Multilayered Oxide Architecture for High Energy-High Voltage Energy Storage – Building Batteries Like Semiconductors
Path towards electrification of automobiles relies on realization of high-voltage (>4.3 V vs. Li), high-reversible areal capacity (3-4 mAh/cm2) cathodes at a cell level. LiCoO2 (LCO) cathodes are conventionally cycled upto 4.2 V with a specific capacity of 140 mAh/g. Cycling to 4.6 V (~190 mAh/g) is hindered by accelerated bulk structural degradation mechanisms and surface reaction between the delithiated lattice (Li0.3CoO2) and the electrolyte (~1.0-1.2 M LiPF6 in a mixture of polycarbonates). To realize a high-voltage, high-capacity cathode design, we demonstrate an all electrochemically grown multilayer architecture with a core capable of providing high-capacity and rate capability; and a shell oxide capping layer to suppress harmful side reactions occurring at voltages beyond 4.2 V vs. Li.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (26) , 1367
An All-Electrodeposited Multilayered Oxide Architecture for High Energy-High Voltage Energy Storage – Building Batteries Like Semiconductors
Path towards electrification of automobiles relies on realization of high-voltage (>4.3 V vs. Li), high-reversible areal capacity (3-4 mAh/cm2) cathodes at a cell level. LiCoO2 (LCO) cathodes are conventionally cycled upto 4.2 V with a specific capacity of 140 mAh/g. Cycling to 4.6 V (~190 mAh/g) is hindered by accelerated bulk structural degradation mechanisms and surface reaction between the delithiated lattice (Li0.3CoO2) and the electrolyte (~1.0-1.2 M LiPF6 in a mixture of polycarbonates). To realize a high-voltage, high-capacity cathode design, we demonstrate an all electrochemically grown multilayer architecture with a core capable of providing high-capacity and rate capability; and a shell oxide capping layer to suppress harmful side reactions occurring at voltages beyond 4.2 V vs. Li.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (58) , 461
Plasma Assisted Surface Modification and Transition Metals (TMs) Doping of Lithium Cobalt Oxide (LCO) Cathode for High-Voltage Lithium-Ion Batteries
Lithium cobalt oxide cathode (LCO) is extensively used as a cathode material in lithium-ion batteries for portable electronics. It is among the highest-performing cathode materials because of its structural stability, long cycle life, and high volumetric density at a cut-off voltage of 4.2 V (vs. Li/Li+). Significant energy density increases would be provided by lifting the cut-off voltage from 4.2 V to 4.6 V (vs. Li/Li+), increasing the specific capacity from 140 mhA/g to 190 mAh/g. However, at high-voltages, the cathode material undergoes severe challenges such as unstable cathode-electrolyte interface (CEI), undesirable permanent phase transformations, and oxygen loss which limit energy density and cycle life. To improve the high-voltage stability and electrochemical performance of LCO, we demonstrate plasma-assisted surface modification and fluorine, and transition metal doping. Incorporation of fluorine, in combination with transition elemental doping, protects the surface by reconstructing the layered structure of LCO into a short-range disordered rocksalt structure. Once protected, the LCO can be cycled to higher voltages, resulting in an enhanced energy density and cycle-life. Time-of-Flight Secondary Ion Mass Spectroscopy (ToF-SIMS) analysis of both untreated and plasma engineered LCO confirms fluorination of the surface of plasma treated LCO. X-ray Fluorescence (XRF) and ToF-SIMS analyses of the plasma modified and pristine LCO show the incorporation of transition metals in the surface. High resolution STEM indicates that the surface is reconstructed from a layered LCO structure to a local disordered rocksalt structure. SEM images of the pristine and plasma treated LCO before and after cycling clearly show the increased stability of the plasma-treated material. surface modifications. At higher cycling voltages (4.6 V vs Li/Li+) plasma modified LCO cathodes show significantly improved electrochemical results including longer cycle life, higher capacity retention, and higher energy density.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (58) , 461
Plasma Assisted Surface Modification and Transition Metals (TMs) Doping of Lithium Cobalt Oxide (LCO) Cathode for High-Voltage Lithium-Ion Batteries
Lithium cobalt oxide cathode (LCO) is extensively used as a cathode material in lithium-ion batteries for portable electronics. It is among the highest-performing cathode materials because of its structural stability, long cycle life, and high volumetric density at a cut-off voltage of 4.2 V (vs. Li/Li+). Significant energy density increases would be provided by lifting the cut-off voltage from 4.2 V to 4.6 V (vs. Li/Li+), increasing the specific capacity from 140 mhA/g to 190 mAh/g. However, at high-voltages, the cathode material undergoes severe challenges such as unstable cathode-electrolyte interface (CEI), undesirable permanent phase transformations, and oxygen loss which limit energy density and cycle life. To improve the high-voltage stability and electrochemical performance of LCO, we demonstrate plasma-assisted surface modification and fluorine, and transition metal doping. Incorporation of fluorine, in combination with transition elemental doping, protects the surface by reconstructing the layered structure of LCO into a short-range disordered rocksalt structure. Once protected, the LCO can be cycled to higher voltages, resulting in an enhanced energy density and cycle-life. Time-of-Flight Secondary Ion Mass Spectroscopy (ToF-SIMS) analysis of both untreated and plasma engineered LCO confirms fluorination of the surface of plasma treated LCO. X-ray Fluorescence (XRF) and ToF-SIMS analyses of the plasma modified and pristine LCO show the incorporation of transition metals in the surface. High resolution STEM indicates that the surface is reconstructed from a layered LCO structure to a local disordered rocksalt structure. SEM images of the pristine and plasma treated LCO before and after cycling clearly show the increased stability of the plasma-treated material. surface modifications. At higher cycling voltages (4.6 V vs Li/Li+) plasma modified LCO cathodes show significantly improved electrochemical results including longer cycle life, higher capacity retention, and higher energy density.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (3) , 492
Elucidating Orientation and Interface Dependent Chemomechanical Degradation Pathways in Polycrystalline Li-Ion Battery Cathodes
Electrochemical performance and chemomechanical degradation pathways in energy storage materials are critically governed by microstructure and sub-particle architecture. At present, lithium-ion battery cathodes are limited to two distinct grain assemblies: “single-crystal cathode” with a single, continuous crystal orientation per grain, and “polycrystal (PC) cathode” consisting of grains possessing internal domains with different crystallographic orientations per grain. Even though polycrystalline cathodes possess enhanced grain boundary Li ion diffusivity due to increased solid-solid interfaces, locally misoriented grains undergo anisotropic volume changes on (de)-lithiation, leading to local phase heterogeneities, which culminate in intergranular microcracking.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (3) , 492
Elucidating Orientation and Interface Dependent Chemomechanical Degradation Pathways in Polycrystalline Li-Ion Battery Cathodes
Electrochemical performance and chemomechanical degradation pathways in energy storage materials are critically governed by microstructure and sub-particle architecture. At present, lithium-ion battery cathodes are limited to two distinct grain assemblies: “single-crystal cathode” with a single, continuous crystal orientation per grain, and “polycrystal (PC) cathode” consisting of grains possessing internal domains with different crystallographic orientations per grain. Even though polycrystalline cathodes possess enhanced grain boundary Li ion diffusivity due to increased solid-solid interfaces, locally misoriented grains undergo anisotropic volume changes on (de)-lithiation, leading to local phase heterogeneities, which culminate in intergranular microcracking.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (3) , 461
Plasma Assisted Surface Modification and Transition Metals (TMs) Doping of Lithium Cobalt Oxide (LCO) Cathode for High-Voltage Lithium-Ion Batteries
Lithium cobalt oxide cathode (LCO) is extensively used as a cathode material in lithium-ion batteries for portable electronics. It is among the highest-performing cathode materials because of its structural stability, long cycle life, and high volumetric density at a cut-off voltage of 4.2 V (vs. Li/Li+). Significant energy density increases would be provided by lifting the cut-off voltage from 4.2 V to 4.6 V (vs. Li/Li+), increasing the specific capacity from 140 mhA/g to 190 mAh/g. However, at high-voltages, the cathode material undergoes severe challenges such as unstable cathode-electrolyte interface (CEI), undesirable permanent phase transformations, and oxygen loss which limit energy density and cycle life. To improve the high-voltage stability and electrochemical performance of LCO, we demonstrate plasma-assisted surface modification and fluorine, and transition metal doping. Incorporation of fluorine, in combination with transition elemental doping, protects the surface by reconstructing the layered structure of LCO into a short-range disordered rocksalt structure. Once protected, the LCO can be cycled to higher voltages, resulting in an enhanced energy density and cycle-life. Time-of-Flight Secondary Ion Mass Spectroscopy (ToF-SIMS) analysis of both untreated and plasma engineered LCO confirms fluorination of the surface of plasma treated LCO. X-ray Fluorescence (XRF) and ToF-SIMS analyses of the plasma modified and pristine LCO show the incorporation of transition metals in the surface. High resolution STEM indicates that the surface is reconstructed from a layered LCO structure to a local disordered rocksalt structure. SEM images of the pristine and plasma treated LCO before and after cycling clearly show the increased stability of the plasma-treated material. surface modifications. At higher cycling voltages (4.6 V vs Li/Li+) plasma modified LCO cathodes show significantly improved electrochemical results including longer cycle life, higher capacity retention, and higher energy density.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (3) , 461
Plasma Assisted Surface Modification and Transition Metals (TMs) Doping of Lithium Cobalt Oxide (LCO) Cathode for High-Voltage Lithium-Ion Batteries
Lithium cobalt oxide cathode (LCO) is extensively used as a cathode material in lithium-ion batteries for portable electronics. It is among the highest-performing cathode materials because of its structural stability, long cycle life, and high volumetric density at a cut-off voltage of 4.2 V (vs. Li/Li+). Significant energy density increases would be provided by lifting the cut-off voltage from 4.2 V to 4.6 V (vs. Li/Li+), increasing the specific capacity from 140 mhA/g to 190 mAh/g. However, at high-voltages, the cathode material undergoes severe challenges such as unstable cathode-electrolyte interface (CEI), undesirable permanent phase transformations, and oxygen loss which limit energy density and cycle life. To improve the high-voltage stability and electrochemical performance of LCO, we demonstrate plasma-assisted surface modification and fluorine, and transition metal doping. Incorporation of fluorine, in combination with transition elemental doping, protects the surface by reconstructing the layered structure of LCO into a short-range disordered rocksalt structure. Once protected, the LCO can be cycled to higher voltages, resulting in an enhanced energy density and cycle-life. Time-of-Flight Secondary Ion Mass Spectroscopy (ToF-SIMS) analysis of both untreated and plasma engineered LCO confirms fluorination of the surface of plasma treated LCO. X-ray Fluorescence (XRF) and ToF-SIMS analyses of the plasma modified and pristine LCO show the incorporation of transition metals in the surface. High resolution STEM indicates that the surface is reconstructed from a layered LCO structure to a local disordered rocksalt structure. SEM images of the pristine and plasma treated LCO before and after cycling clearly show the increased stability of the plasma-treated material. surface modifications. At higher cycling voltages (4.6 V vs Li/Li+) plasma modified LCO cathodes show significantly improved electrochemical results including longer cycle life, higher capacity retention, and higher energy density.
- 12 January 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (4) , 4147-4165
Electrochemically Tuned Crystal Tectonics in Crack-Resistant Textured Oxide Cathode Films for Electrochemical Energy Storage
Electro-chemo-mechanical degradation pathways that significantly impact performance of ceramic battery electrodes are a strong function of bulk crystallographic texture, crystal size, and interfacial misorientation angle. Via electrodeposition, deterministic synthesis of textured thick (>10 μm) films of LiCoO2 having controlled size dispersity and interfaces is demonstrated, enabling study and control of these degradation pathways. The crystal morphogenesis stems from the growth parameters (current density and temperature), resulting in a bouquet of textures and microstructures. Columnar grained ⟨110⟩||ND textured films with a finer crystallite size (f4-8 μm = 0.617) can be synthesized in kinetic regimes of growth (T = 275 °C, supersaturation >0.367), whereas ⟨003⟩||ND films with coarser crystals (f8-15 μm = 0.597) originate in thermodynamic regimes of growth (T = 350 °C, supersaturation independent). Interestingly, Σ3 coincident site lattice (CSL)/twin boundaries are controllably incorporated in the ⟨110⟩||ND films (f = 0.337), whereas ⟨003⟩||ND films only possesses high-angle crystal interfaces (HACIs, f = 1.0). The morpho-structural evolution of the crystal assembly under electro-chemo-mechanical stimuli is rooted in crystal tectonics and corelated anisotropic ionic diffusion differences. Stochastic analysis of microstructures of electrochemically cycled films via electron backscatter diffraction (EBSD) and Raman spectroscopy indicates interface-, size-, and texture-dependent degradation modes. On electrochemical cycling, the ⟨003⟩||ND electrode degrades by both intercrystal and intracrystal cracking (13.3% retention), whereas the ⟨110⟩||ND electrode is only susceptible to intercrystal cleavage (89.2% retention). The cracks initiate at local lithiation heterogeneities near coarser crystals and always propagate along HACIs, with all the CSL boundaries remaining mechanically robust. Our discoveries highlight how careful orchestration of orientation and interfaces leads to unique chemomechanical stabilization strategies.
- 12 January 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (4) , 4147-4165
Electrochemically Tuned Crystal Tectonics in Crack-Resistant Textured Oxide Cathode Films for Electrochemical Energy Storage
Electro-chemo-mechanical degradation pathways that significantly impact performance of ceramic battery electrodes are a strong function of bulk crystallographic texture, crystal size, and interfacial misorientation angle. Via electrodeposition, deterministic synthesis of textured thick (>10 μm) films of LiCoO2 having controlled size dispersity and interfaces is demonstrated, enabling study and control of these degradation pathways. The crystal morphogenesis stems from the growth parameters (current density and temperature), resulting in a bouquet of textures and microstructures. Columnar grained ⟨110⟩||ND textured films with a finer crystallite size (f4-8 μm = 0.617) can be synthesized in kinetic regimes of growth (T = 275 °C, supersaturation >0.367), whereas ⟨003⟩||ND films with coarser crystals (f8-15 μm = 0.597) originate in thermodynamic regimes of growth (T = 350 °C, supersaturation independent). Interestingly, Σ3 coincident site lattice (CSL)/twin boundaries are controllably incorporated in the ⟨110⟩||ND films (f = 0.337), whereas ⟨003⟩||ND films only possesses high-angle crystal interfaces (HACIs, f = 1.0). The morpho-structural evolution of the crystal assembly under electro-chemo-mechanical stimuli is rooted in crystal tectonics and corelated anisotropic ionic diffusion differences. Stochastic analysis of microstructures of electrochemically cycled films via electron backscatter diffraction (EBSD) and Raman spectroscopy indicates interface-, size-, and texture-dependent degradation modes. On electrochemical cycling, the ⟨003⟩||ND electrode degrades by both intercrystal and intracrystal cracking (13.3% retention), whereas the ⟨110⟩||ND electrode is only susceptible to intercrystal cleavage (89.2% retention). The cracks initiate at local lithiation heterogeneities near coarser crystals and always propagate along HACIs, with all the CSL boundaries remaining mechanically robust. Our discoveries highlight how careful orchestration of orientation and interfaces leads to unique chemomechanical stabilization strategies.
- Open Access
- 1 December 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Grain engineering in electrodeposited cathodes unifies advantages of single crystal and polycrystal cathodes
Battery cathode microstructures span a spectrum of intra-particle organization, with ‘single-crystal’ and ‘polycrystal’ assemblies being the extremes. Single-crystal cathode particles suffer from poor rate capability but demonstrate high chemical stability. Polycrystal cathodes, comprising particles containing multiple grains, offer enhanced rate capability at the expense of crystallographic heterogeneity and fragile chemomechanics. Employing stochastic multi-grain analysis, our study elucidates that intergranular cracking in polycrystal cathodes is size and interface governed, and all cracking pathways propagate along high angle grain boundaries (HAGB) and never select coincidence site lattice (CSL)/twin boundaries. Drawing from the chemomechanical learnings, we advance electrodeposition as a cathode fabrication technique which unites single-crystal stability with polycrystal rate capability. The electrodeposited cathodes consist of vertically-oriented, columnar nanograins with favorable crystallographic alignment (||sample normal) and a high fraction (~0.5) of crack-resistant CSL/twin boundaries. The grain-engineered electrodes provide high grain boundary diffusivity of a polycrystal with controlled interfaces, while dramatically reducing the cathode-electrolyte surface area and side reactions. Since the electrodeposited cathodes are ~95% dense and free of electrochemically inactive components, they provide a 1.5x increase of volumetric energy density compared to conventional slurry cathodes. Our work guides the future design of grain-engineered assemblies for tunable ion and electron transport and mechanical response.
- 1 December 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessGrain engineering in electrodeposited cathodes unifies advantages of single crystal and polycrystal cathodes
Battery cathode microstructures span a spectrum of intra-particle organization, with ‘single-crystal’ and ‘polycrystal’ assemblies being the extremes. Single-crystal cathode particles suffer from poor rate capability but demonstrate high chemical stability. Polycrystal cathodes, comprising particles containing multiple grains, offer enhanced rate capability at the expense of crystallographic heterogeneity and fragile chemomechanics. Employing stochastic multi-grain analysis, our study elucidates that intergranular cracking in polycrystal cathodes is size and interface governed, and all cracking pathways propagate along high angle grain boundaries (HAGB) and never select coincidence site lattice (CSL)/twin boundaries. Drawing from the chemomechanical learnings, we advance electrodeposition as a cathode fabrication technique which unites single-crystal stability with polycrystal rate capability. The electrodeposited cathodes consist of vertically-oriented, columnar nanograins with favorable crystallographic alignment (||sample normal) and a high fraction (~0.5) of crack-resistant CSL/twin boundaries. The grain-engineered electrodes provide high grain boundary diffusivity of a polycrystal with controlled interfaces, while dramatically reducing the cathode-electrolyte surface area and side reactions. Since the electrodeposited cathodes are ~95% dense and free of electrochemically inactive components, they provide a 1.5x increase of volumetric energy density compared to conventional slurry cathodes. Our work guides the future design of grain-engineered assemblies for tunable ion and electron transport and mechanical response.
- Open Access
- 30 September 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Electrochemically tuned crystal tectonics in crack-resistant textured oxide cathode films for electrochemical energy storage
Electro-chemo-mechanical degradation pathways which significantly impact performance of ceramic (e.g., LiCoO2) battery electrodes are a strong function of bulk crystallographic texture, crystal size and interfacial misorientation angle. Via electrodeposition, deterministic synthesis of textured thick (>10 µm) films of LiCoO2 with iso-oriented crystalline domains having controlled size dispersity and interfaces enabling study and control of these degradation pathways is demonstrated. The crystal morphogenesis stem from the growth parameters (current density and growth temperature), resulting in a bouquet of textures and microstructures. Columnar grained ||ND textured films with a finer crystallite size (f4-8µm=0.617) can be synthesized in kinetic regimes of growth (T=275°C, supersaturation>0.367), whereas ||ND films with coarse, polygonal crystals (f8-15µm=0.597) originate in thermodynamic regimes of growth (T=275°C, supersaturation<0.036; T=350°C, supersaturation independent). Interestingly, Σ3 coincident site lattice (CSL) boundaries are controllably incorporated in the ||ND films as low energy interfaces (f = 0.337), whereas IIND films only possesses high angle crystal interfaces (HACIs, f = 1.0). The morpho-structural evolution of the crystal assembly under electro-chemo-mechanical stimuli is rooted in the crystal tectonics and co-related anisotropic ionic diffusion differences. Stochastic analysis of microstructures of electrochemically cycled films via electron backscatter diffraction (EBSD) and Raman spectroscopy indicates interface, size and texture-dependent degradation modes. On electrochemical cycling, ||ND electrode degrades by both intercrystal and intracrystal cracking (13.3% retention, critical size 1.79 µm), whereas ||ND electrode is only susceptible to intercrystal cleavage (89.2% retention, critical size 2.25 µm). The cracks initiate at local lithiation heterogeneities near coarser crystals and always propagate along HACIs; with all the CSL boundaries remaining mechanically robust. Our discoveries highlight how careful orchestration of orientation and interfaces leads to unique chemomechanical stabilization strategies.
- 30 September 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessElectrochemically tuned crystal tectonics in crack-resistant textured oxide cathode films for electrochemical energy storage
Electro-chemo-mechanical degradation pathways which significantly impact performance of ceramic (e.g., LiCoO2) battery electrodes are a strong function of bulk crystallographic texture, crystal size and interfacial misorientation angle. Via electrodeposition, deterministic synthesis of textured thick (>10 µm) films of LiCoO2 with iso-oriented crystalline domains having controlled size dispersity and interfaces enabling study and control of these degradation pathways is demonstrated. The crystal morphogenesis stem from the growth parameters (current density and growth temperature), resulting in a bouquet of textures and microstructures. Columnar grained ||ND textured films with a finer crystallite size (f4-8µm=0.617) can be synthesized in kinetic regimes of growth (T=275°C, supersaturation>0.367), whereas ||ND films with coarse, polygonal crystals (f8-15µm=0.597) originate in thermodynamic regimes of growth (T=275°C, supersaturation<0.036; T=350°C, supersaturation independent). Interestingly, Σ3 coincident site lattice (CSL) boundaries are controllably incorporated in the ||ND films as low energy interfaces (f = 0.337), whereas IIND films only possesses high angle crystal interfaces (HACIs, f = 1.0). The morpho-structural evolution of the crystal assembly under electro-chemo-mechanical stimuli is rooted in the crystal tectonics and co-related anisotropic ionic diffusion differences. Stochastic analysis of microstructures of electrochemically cycled films via electron backscatter diffraction (EBSD) and Raman spectroscopy indicates interface, size and texture-dependent degradation modes. On electrochemical cycling, ||ND electrode degrades by both intercrystal and intracrystal cracking (13.3% retention, critical size 1.79 µm), whereas ||ND electrode is only susceptible to intercrystal cleavage (89.2% retention, critical size 2.25 µm). The cracks initiate at local lithiation heterogeneities near coarser crystals and always propagate along HACIs; with all the CSL boundaries remaining mechanically robust. Our discoveries highlight how careful orchestration of orientation and interfaces leads to unique chemomechanical stabilization strategies.
- Open Access
- 19 August 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (2)
Single‐Step Electrochemical Battery Recycling
Sustainable battery production is a major challenge for the future of electrification with the rise in battery production leading to a massive increase in demand for battery cathode materials. Needed are environmentally responsible ways to recycle used cathodes into new cathodes to create a circular economy for batteries. While some battery recycling and recovery techniques for battery components are developed, they can involve costly and environmentally impactful multi‐step processes. This work demonstrates for the first time the simultaneous dissolution and electrochemical deposition of Li‐ion transition metal oxide cathodes, providing a path to directly fabricate new battery cathodes from old battery cathodes. The LiCoO 2 cathodes formed via this recycling process exhibit near‐theoretical capacities, are binder and additive‐free, and are phase pure. Technoeconomic and life cycle analyses show the simultaneous dissolution and electrochemical deposition process is less costly and environmentally harmful than traditional pyrometallurgical, hydrometallurgical, and direct recycling methods. This method has major potential impacts and advantages on the industrial scale as it creates battery materials in fewer steps at a lower cost and with a lower environmental impact than current battery recycling methods.
- 19 August 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (2)
Open AccessSingle‐Step Electrochemical Battery Recycling
Sustainable battery production is a major challenge for the future of electrification with the rise in battery production leading to a massive increase in demand for battery cathode materials. Needed are environmentally responsible ways to recycle used cathodes into new cathodes to create a circular economy for batteries. While some battery recycling and recovery techniques for battery components are developed, they can involve costly and environmentally impactful multi‐step processes. This work demonstrates for the first time the simultaneous dissolution and electrochemical deposition of Li‐ion transition metal oxide cathodes, providing a path to directly fabricate new battery cathodes from old battery cathodes. The LiCoO 2 cathodes formed via this recycling process exhibit near‐theoretical capacities, are binder and additive‐free, and are phase pure. Technoeconomic and life cycle analyses show the simultaneous dissolution and electrochemical deposition process is less costly and environmentally harmful than traditional pyrometallurgical, hydrometallurgical, and direct recycling methods. This method has major potential impacts and advantages on the industrial scale as it creates battery materials in fewer steps at a lower cost and with a lower environmental impact than current battery recycling methods.
- 9 October 2022
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2022-02 (24) , 996
Molten Hydroxide Electrodeposition of Transition Metal Oxide Cathodes for Electrochemical Energy Storage
State-of-the-art synthesis for layered oxide cathodes for Li and Na-ion battery involves prolonged high temperature (>700°C) multistep processing for long reaction times (~24 hours) under high oxygen pressure, followed by slurry casting after mixing with binders and additives. Here, we demonstrate an intermediate temperature (250-350°C) molten hydroxide-based electrodeposition process to grow alkali ion (Li+, Na+) intercalated transition metal oxides across multiple transition metal chemistries of the Li system (from layered LiCoO2 to cobalt-less orthorhombic LiMnO2, layered Li2MnO3, spinel LiNixMn1-xO4, LiMn2O4,) and Na system (O3 and P2 NaxCoO2, O’3 NaxMnO2) in thick film form factors. The highly textured ([110]||ND), dense (>95%) electroplated LiCoO2 cathodes can perform at ultrahigh thickness of ~200 µm (areal capacity ~13.6 mAh/cm2) in comparison to 40-60 µm for state-of-the-art slurry cast cathodes (areal capacity ~3-4 mAh/cm2 with a porosity of ~20%), a fivefold increase in areal capacity and volumetric energy density. We discuss the interplay of bulk crystallographic orientation of the electro-active material (LiCoO2), surface terminating planes interacting with the electrolyte, and electrochemically grown conformal surface protective layers on the electrochemical-chemo-mechanical degradation mechanisms during intercalation and deintercalation for high voltage operation (>4.2 V vs. Li). We also demonstrate electrochemically controllable isovalent transition metal doping and substitution in ceramic oxides (LiCoxMn1-xO2) by electrodeposition. Our findings highlight the influence of the unique molten hydroxide-based solution chemistry platform and electrochemical processing parameters, on regulating the phase assemblage, designing the microstructure, and controlling crystallographic orientation during electrocrystallization.
- 9 October 2022
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2022-02 (24) , 996
Molten Hydroxide Electrodeposition of Transition Metal Oxide Cathodes for Electrochemical Energy Storage
State-of-the-art synthesis for layered oxide cathodes for Li and Na-ion battery involves prolonged high temperature (>700°C) multistep processing for long reaction times (~24 hours) under high oxygen pressure, followed by slurry casting after mixing with binders and additives. Here, we demonstrate an intermediate temperature (250-350°C) molten hydroxide-based electrodeposition process to grow alkali ion (Li+, Na+) intercalated transition metal oxides across multiple transition metal chemistries of the Li system (from layered LiCoO2 to cobalt-less orthorhombic LiMnO2, layered Li2MnO3, spinel LiNixMn1-xO4, LiMn2O4,) and Na system (O3 and P2 NaxCoO2, O’3 NaxMnO2) in thick film form factors. The highly textured ([110]||ND), dense (>95%) electroplated LiCoO2 cathodes can perform at ultrahigh thickness of ~200 µm (areal capacity ~13.6 mAh/cm2) in comparison to 40-60 µm for state-of-the-art slurry cast cathodes (areal capacity ~3-4 mAh/cm2 with a porosity of ~20%), a fivefold increase in areal capacity and volumetric energy density. We discuss the interplay of bulk crystallographic orientation of the electro-active material (LiCoO2), surface terminating planes interacting with the electrolyte, and electrochemically grown conformal surface protective layers on the electrochemical-chemo-mechanical degradation mechanisms during intercalation and deintercalation for high voltage operation (>4.2 V vs. Li). We also demonstrate electrochemically controllable isovalent transition metal doping and substitution in ceramic oxides (LiCoxMn1-xO2) by electrodeposition. Our findings highlight the influence of the unique molten hydroxide-based solution chemistry platform and electrochemical processing parameters, on regulating the phase assemblage, designing the microstructure, and controlling crystallographic orientation during electrocrystallization.