Xian-Ci Zhong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xian-Ci Zhong has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Ke-Shi Zhang
Key Lab of Disaster Prevention and Structural Safety, College of Civil Engineering and Architecture, Guangxi University, Nanning 530004, China
8 shared publications Xiao-Yu Long
4 shared publicationsFang-Shi Duan
2 shared publicationsHan-Mei Wei
School of Mathematics and Information ScienceGuangxi University, Nanning, P.R. China
2 shared publications- Kang Yong Lee
Yonsei University
2 shared publications Q. A. Huang
School of Mathematics and Information Science, Guangxi University, Nanning, Guangxi, P.R. China
2 shared publications
Latest Publications
- 6 September 2026
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 341
A thermal-medium Dugdale–Barenblatt crack model with equal saturation and yielding zone lengths
- 6 September 2026
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 341
A thermal-medium Dugdale–Barenblatt crack model with equal saturation and yielding zone lengths
- 26 February 2026
- Published by Springer Nature in Natural Hazards
- Vol. 122 (6) , 242
Evaluating and enhancing the performance of satellite precipitation products by considering uncertainty in rain gauge observations
- 26 February 2026
- Published by Springer Nature in Natural Hazards
- Vol. 122 (6) , 242
Evaluating and enhancing the performance of satellite precipitation products by considering uncertainty in rain gauge observations
- 27 September 2025
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 241, 763-786
Optimization-driven group decision making with XOR comparison matrices
- 27 September 2025
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 241, 763-786
Optimization-driven group decision making with XOR comparison matrices
- Open Access
Stress–Strain Hysteresis Loop-Based Machine Learning Models for Predicting Metal Fatigue Life Under Uncertainty
This paper reports machine learning models for predicting metal fatigue life under uncertainty by extracting stress–strain data from hysteresis loops. First, the hysteresis loops of Q235B under strain-controlled constant amplitude loading are analyzed. The values of stress and strain in six key points are extracted from each hysteresis loop at the earliest stages of the fatigue process, and transformed into polar coordinates. Second, the uncertainty is quantified by extending the applied strain amplitude and the selected stress–strain values to intervals. A great deal of data are generated randomly in each interval for coping with the challenge of a small fatigue test dataset. Third, three machine learning models are constructed, where the parameters of the back-propagation neural network model are optimized by using the leave-one-out cross-validation technique, and the models of support vector regression and random forest are selected carefully. The point and interval predictions of the low-cycle-fatigue life of Q235B are reported to reveal the feasibility and advantage of the proposed models. The results help to identify how to understand the fatigue behavior of materials by combining machine learning models and stress–strain hysteresis loops.
Open AccessStress–Strain Hysteresis Loop-Based Machine Learning Models for Predicting Metal Fatigue Life Under Uncertainty
This paper reports machine learning models for predicting metal fatigue life under uncertainty by extracting stress–strain data from hysteresis loops. First, the hysteresis loops of Q235B under strain-controlled constant amplitude loading are analyzed. The values of stress and strain in six key points are extracted from each hysteresis loop at the earliest stages of the fatigue process, and transformed into polar coordinates. Second, the uncertainty is quantified by extending the applied strain amplitude and the selected stress–strain values to intervals. A great deal of data are generated randomly in each interval for coping with the challenge of a small fatigue test dataset. Third, three machine learning models are constructed, where the parameters of the back-propagation neural network model are optimized by using the leave-one-out cross-validation technique, and the models of support vector regression and random forest are selected carefully. The point and interval predictions of the low-cycle-fatigue life of Q235B are reported to reveal the feasibility and advantage of the proposed models. The results help to identify how to understand the fatigue behavior of materials by combining machine learning models and stress–strain hysteresis loops.
- 5 November 2022
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 276
A process-data-driven BP neural network model for predicting interval-valued fatigue life of metals
- 5 November 2022
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 276
A process-data-driven BP neural network model for predicting interval-valued fatigue life of metals
- 13 March 2022
- Published by Elsevier in Applied Mathematical Modelling
- Vol. 107, 508-529
Approximate structures of thermoelastic fields induced by a penny-shaped thermal-medium crack in a transversely isotropic layer
- 13 March 2022
- Published by Elsevier in Applied Mathematical Modelling
- Vol. 107, 508-529
Approximate structures of thermoelastic fields induced by a penny-shaped thermal-medium crack in a transversely isotropic layer
- 22 October 2019
- Published by Springer Nature in Acta Mechanica Solida Sinica
- Vol. 33 (4) , 521-545
An Extended Dielectric Crack Model for Fracture Analysis of a Thermopiezoelectric Strip
- 22 October 2019
- Published by Springer Nature in Acta Mechanica Solida Sinica
- Vol. 33 (4) , 521-545
An Extended Dielectric Crack Model for Fracture Analysis of a Thermopiezoelectric Strip
- 27 July 2019
- Published by SAGE Publications in Mathematics and Mechanics of Solids
- Vol. 24 (12) , 4078-4100
Thermoelastic analysis of a cracked orthotropic strip under heat conduction effect of crack interior
The problem of a Griffith crack embedded in an orthotropic strip is investigated under a combination of thermal and mechanical loadings. The extended thermal-medium crack model is used to address the effects of thermal conductivity of crack interior on the fracture parameters of concerns. Using the Fourier transform technique, the boundary-value problem is reduced to solving singular integral equations with Cauchy kernel. The closed-form solutions of temperature fields are determined. In solving the elastic fields, the Lobatto–Chebyshev integration formula is applied to discretize the obtained singular integral equations as a system of algebraic equations, which is solved by elaborating an algorithm. Numerical results are reported to illustrate the effects of the thermal conductivity inside crack and the thickness of orthotropic strip on the partial insulation coefficient, the thermal stress intensity factor, and the strain energy density factor. The crack initiation behavior is analyzed according to the normalized strain energy density factor. The observations reveal that the crack-tip thermoelastic fields in an orthotropic strip are dependent on the combined effects of the thermoelastic loadings, the physical and geometrical properties of the material and crack. Some comparisons with the existing works are offered to show the novelty and applicability of the obtained results.
- 27 July 2019
- Published by SAGE Publications in Mathematics and Mechanics of Solids
- Vol. 24 (12) , 4078-4100
Thermoelastic analysis of a cracked orthotropic strip under heat conduction effect of crack interior
The problem of a Griffith crack embedded in an orthotropic strip is investigated under a combination of thermal and mechanical loadings. The extended thermal-medium crack model is used to address the effects of thermal conductivity of crack interior on the fracture parameters of concerns. Using the Fourier transform technique, the boundary-value problem is reduced to solving singular integral equations with Cauchy kernel. The closed-form solutions of temperature fields are determined. In solving the elastic fields, the Lobatto–Chebyshev integration formula is applied to discretize the obtained singular integral equations as a system of algebraic equations, which is solved by elaborating an algorithm. Numerical results are reported to illustrate the effects of the thermal conductivity inside crack and the thickness of orthotropic strip on the partial insulation coefficient, the thermal stress intensity factor, and the strain energy density factor. The crack initiation behavior is analyzed according to the normalized strain energy density factor. The observations reveal that the crack-tip thermoelastic fields in an orthotropic strip are dependent on the combined effects of the thermoelastic loadings, the physical and geometrical properties of the material and crack. Some comparisons with the existing works are offered to show the novelty and applicability of the obtained results.
- Open Access
- 1 January 2019
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2019 (1)
A Particle Swarm Optimization‐Based Method for Numerically Solving Ordinary Differential Equations
The Euler method is a typical one for numerically solving initial value problems of ordinary differential equations. Particle swarm optimization (PSO) is an efficient algorithm for obtaining the optimal solution of a nonlinear optimization problem. In this study, a PSO‐based Euler‐type method is proposed to solve the initial value problem of ordinary differential equations. In the typical Euler method, the equidistant grid points are always used to obtain the approximate solution. The existing shortcoming is that when the iteration number is increasing, the approximate solution could be greatly away from the exact one. Here, it is considered that the distribution of the grid nodes could affect the approximate solution of differential equations on the discrete points. The adopted grid points are assumed to be free and nonequidistant. An optimization problem is constructed and solved by particle swarm optimization (PSO) to determine the distribution of grid points. Through numerical computations, some comparisons are offered to reveal that the proposed method has great advantages and can overcome the existing shortcoming of the typical Euler formulae.
- 1 January 2019
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2019 (1)
Open AccessA Particle Swarm Optimization‐Based Method for Numerically Solving Ordinary Differential Equations
The Euler method is a typical one for numerically solving initial value problems of ordinary differential equations. Particle swarm optimization (PSO) is an efficient algorithm for obtaining the optimal solution of a nonlinear optimization problem. In this study, a PSO‐based Euler‐type method is proposed to solve the initial value problem of ordinary differential equations. In the typical Euler method, the equidistant grid points are always used to obtain the approximate solution. The existing shortcoming is that when the iteration number is increasing, the approximate solution could be greatly away from the exact one. Here, it is considered that the distribution of the grid nodes could affect the approximate solution of differential equations on the discrete points. The adopted grid points are assumed to be free and nonequidistant. An optimization problem is constructed and solved by particle swarm optimization (PSO) to determine the distribution of grid points. Through numerical computations, some comparisons are offered to reveal that the proposed method has great advantages and can overcome the existing shortcoming of the typical Euler formulae.
- Open Access
Experimental Investigations on Subsequent Yield Surface of Pure Copper by Single-Sample and Multi-Sample Methods under Various Pre-Deformation
Using copper thin-walled tubular specimens, the subsequent yield surfaces under pre-tension, pre-torsion and pre-combined tension-torsion are measured, where the single-sample and multi-sample methods are applied respectively to determine the yield stresses at specified offset strain. The rule and characteristics of the evolution of the subsequent yield surface are investigated. Under the conditions of different pre-strains, the influence of test point number, test sequence and specified offset strain on the measurement of subsequent yield surface and the concave phenomenon for measured yield surface are studied. Moreover, the feasibility and validity of the two methods are compared. The main conclusions are drawn as follows: (1) For the single or multi-sample method, the measured subsequent yield surfaces are remarkably different from cylindrical yield surfaces proposed by the classical plasticity theory; (2) there are apparent differences between the test results from the two kinds of methods: the multi-sample method is not influenced by the number of test points, test order and the cumulative effect of residual plastic strain resulting from the other test point, while those are very influential in the single-sample method; and (3) the measured subsequent yield surface may appear concave, which can be transformed to convex for single-sample method by changing the test sequence. However, for the multiple-sample method, the concave phenomenon will disappear when a larger offset strain is specified.
Open AccessExperimental Investigations on Subsequent Yield Surface of Pure Copper by Single-Sample and Multi-Sample Methods under Various Pre-Deformation
Using copper thin-walled tubular specimens, the subsequent yield surfaces under pre-tension, pre-torsion and pre-combined tension-torsion are measured, where the single-sample and multi-sample methods are applied respectively to determine the yield stresses at specified offset strain. The rule and characteristics of the evolution of the subsequent yield surface are investigated. Under the conditions of different pre-strains, the influence of test point number, test sequence and specified offset strain on the measurement of subsequent yield surface and the concave phenomenon for measured yield surface are studied. Moreover, the feasibility and validity of the two methods are compared. The main conclusions are drawn as follows: (1) For the single or multi-sample method, the measured subsequent yield surfaces are remarkably different from cylindrical yield surfaces proposed by the classical plasticity theory; (2) there are apparent differences between the test results from the two kinds of methods: the multi-sample method is not influenced by the number of test points, test order and the cumulative effect of residual plastic strain resulting from the other test point, while those are very influential in the single-sample method; and (3) the measured subsequent yield surface may appear concave, which can be transformed to convex for single-sample method by changing the test sequence. However, for the multiple-sample method, the concave phenomenon will disappear when a larger offset strain is specified.