Alexander Čapka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexander Čapka has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Milan Žaludek
7 shared publications- Soňa Rusnáková
Department of Production Engineering, Faculty of Technology, Tomas Bata University in Zlín, Vavrečkova 275, 760 01 Zlín, Czech Republic
6 shared publications Ladislav Fojtl
FT TBU in Zlín
4 shared publicationsVladimír Rusnák
VŠB –Technical University of Ostrava
3 shared publications- Konstantinos Karvanis
Tomas Bata University in Zlín
2 shared publications - Ladislav Fojtl
FT TBU in Zlín
2 shared publications
Latest Publications
- Open Access
- 1 October 2018
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 18 (5) , 727-731
Fatigue Life of Al-Honeycomb Core Composites Construction
Detail záznamu - Fatigue life of Al-honeycomb core composites construction - Detail záznamu - Vědecká knihovna UJEP
- 1 October 2018
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 18 (5) , 727-731
Open AccessFatigue Life of Al-Honeycomb Core Composites Construction
Detail záznamu - Fatigue life of Al-honeycomb core composites construction - Detail záznamu - Vědecká knihovna UJEP
- Open Access
- 22 May 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 362 (1) , 012005
Preparation and Dynamic Mechanical Analysis of Glass or carbon Fiber/Polymer Composites
- 22 May 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 362 (1) , 012005
Open AccessPreparation and Dynamic Mechanical Analysis of Glass or carbon Fiber/Polymer Composites
- 8 May 2017
- Published by Taylor & Francis in Quantitative InfraRed Thermography Journal
- Vol. 14 (2) , 206-217
Modelling, detecting and evaluating water ingress in aviation honeycomb panels
The use of infrared thermography for quantitative evaluation of water ingress in aviation honeycomb cells is discussed. Numerical modelling has been performed by analysing a 3D panel model where water fully or partially occupies honeycomb cells. Calculation of several test cases has allowed better understanding of how the thickness of the water layer affects surface temperature anomalies and times of their appearance in active one-sided thermal tests. Experimental results have been obtained on both reference samples and real honeycomb panels.
- 8 May 2017
- Published by Taylor & Francis in Quantitative InfraRed Thermography Journal
- Vol. 14 (2) , 206-217
Modelling, detecting and evaluating water ingress in aviation honeycomb panels
The use of infrared thermography for quantitative evaluation of water ingress in aviation honeycomb cells is discussed. Numerical modelling has been performed by analysing a 3D panel model where water fully or partially occupies honeycomb cells. Calculation of several test cases has allowed better understanding of how the thickness of the water layer affects surface temperature anomalies and times of their appearance in active one-sided thermal tests. Experimental results have been obtained on both reference samples and real honeycomb panels.
- 22 March 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 891, 542-546
Manufacturing and Mechanical Characterization of Bio-Based Laminates and Sandwich Structures
Jute fabric is well-known reinforcing material in composite science, however, there is a necessity to treat these fabrics to reduce moisture uptake and improve properties. Nevertheless, every modification increases the cost and reduces the possible applications. Presented research deals with an investigation of possibility to use untreated jute in various fabric weight as a reinforcing material in sandwich structures facings. Untreated jute reinforcements and two types of cork cores were saturated in one step during vacuum infusion creating a lightweight sandwich composite. All samples were mechanically tested in three-point bending test. Experimental results showed the most appropriate material combination and produced sandwich structure are proposed for design applications.
- 22 March 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 891, 542-546
Manufacturing and Mechanical Characterization of Bio-Based Laminates and Sandwich Structures
Jute fabric is well-known reinforcing material in composite science, however, there is a necessity to treat these fabrics to reduce moisture uptake and improve properties. Nevertheless, every modification increases the cost and reduces the possible applications. Presented research deals with an investigation of possibility to use untreated jute in various fabric weight as a reinforcing material in sandwich structures facings. Untreated jute reinforcements and two types of cork cores were saturated in one step during vacuum infusion creating a lightweight sandwich composite. All samples were mechanically tested in three-point bending test. Experimental results showed the most appropriate material combination and produced sandwich structure are proposed for design applications.
- 22 March 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 891, 516-521
Detecting Water in Composite Sandwich Panels by Using Infrared Thermography
Honeycomb composite structures widely used in aviation are sturdy and light-weight but they may accumulate water from the atmosphere during aircraft operation. The presence of water in honeycomb cells leads to a higher airplane mass and excessive corrosion of aluminum cores, while the frozen water endangers panel integrity. This work describes the use of infrared thermography for detecting water trapped in aviation honeycomb cells.
- 22 March 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 891, 516-521
Detecting Water in Composite Sandwich Panels by Using Infrared Thermography
Honeycomb composite structures widely used in aviation are sturdy and light-weight but they may accumulate water from the atmosphere during aircraft operation. The presence of water in honeycomb cells leads to a higher airplane mass and excessive corrosion of aluminum cores, while the frozen water endangers panel integrity. This work describes the use of infrared thermography for detecting water trapped in aviation honeycomb cells.
- Open Access
- 1 August 2016
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 16 (4) , 799-804
Technology and Mold Design for Production of Hollow Carbon Composite Parts
This essay aims to describe technology and mold design for production of hollow composite parts like carbon rims or sport rackets. Tested materials correspond to those used for composites in sport applications. Production technology called inf...
- 1 August 2016
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 16 (4) , 799-804
Open AccessTechnology and Mold Design for Production of Hollow Carbon Composite Parts
This essay aims to describe technology and mold design for production of hollow composite parts like carbon rims or sport rackets. Tested materials correspond to those used for composites in sport applications. Production technology called inf...
- 22 February 2016
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 827, 141-144
Analysis of Mechanical and Impact Properties of Prepreg Composites under Elevated Temperature
This paper presents an experimental investigation of mechanical and impact properties of carbon and Kevlar-glass composites prepared from pre-impregnated materials. Namely, flexural performance in three-point bending at different temperatures is evaluated. Moreover, Charpy impact test and low-velocity impact test are also conducted for classification of impact properties and character of rupture. These all properties are important for material design of sport bike rims and many sport and other applications.
- 22 February 2016
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 827, 141-144
Analysis of Mechanical and Impact Properties of Prepreg Composites under Elevated Temperature
This paper presents an experimental investigation of mechanical and impact properties of carbon and Kevlar-glass composites prepared from pre-impregnated materials. Namely, flexural performance in three-point bending at different temperatures is evaluated. Moreover, Charpy impact test and low-velocity impact test are also conducted for classification of impact properties and character of rupture. These all properties are important for material design of sport bike rims and many sport and other applications.
- 31 July 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1120-1121, 531-534
Experimental Investigation of Possibilities Vacuum Infusion Technology to Produce Composite Ribs
In the present work, mechanical properties and bending stiffness of composite structures with ribs are studied. The aim of this work was making ribbed composite structures in one step, where the ribs are inserted between glass reinforcement of composite system. In practice, the ribs on the composite structure (final products) are glued, but where there is a lower strength (according to the type of surface, the surface treatment, suitable bonding technology, the type of glue) and the adhesives are relatively expensive. The production of samples was used technology of vacuum infusion under flexible foil.
- 31 July 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1120-1121, 531-534
Experimental Investigation of Possibilities Vacuum Infusion Technology to Produce Composite Ribs
In the present work, mechanical properties and bending stiffness of composite structures with ribs are studied. The aim of this work was making ribbed composite structures in one step, where the ribs are inserted between glass reinforcement of composite system. In practice, the ribs on the composite structure (final products) are glued, but where there is a lower strength (according to the type of surface, the surface treatment, suitable bonding technology, the type of glue) and the adhesives are relatively expensive. The production of samples was used technology of vacuum infusion under flexible foil.
- 31 July 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1120-1121, 515-518
Characterization of Carbon Composites Properties for Application in Sport Industry
In the present work, mechanical properties of prepreg carbon composites are studied. Five types of composite samples with different number of layers and prepreg material corresponding to material composition used for carbon rims are manufactured by compression molding. Prepared composites are tested and compared with respect to flexural strength and modulus. Furthermore, impact performance using Charpy impact test is also evaluated.
- 31 July 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1120-1121, 515-518
Characterization of Carbon Composites Properties for Application in Sport Industry
In the present work, mechanical properties of prepreg carbon composites are studied. Five types of composite samples with different number of layers and prepreg material corresponding to material composition used for carbon rims are manufactured by compression molding. Prepared composites are tested and compared with respect to flexural strength and modulus. Furthermore, impact performance using Charpy impact test is also evaluated.