Yasuhiro Saito
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yasuhiro Saito has a total of 156 co-authors. Here are the top co-authors by number of shared publications:
Hideyuki Aoki
Department of Chemical Engineering, Graduate School of Engineering, Tohoku University
43 shared publicationsYohsuke Matsushita
Graduate School of Science and Technology, Hirosaki University
34 shared publications- Yoshiya Matsukawa
Department of Chemical Engineering, Graduate School of Engineering, Tohoku University
18 shared publications Masatoshi Daikoku
15 shared publicationsMinori Shirota
15 shared publicationsTakayuki Aoki
15 shared publications
Latest Publications
- Open Access
- 15 August 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (9) , 982-991
Three-dimensional Pore Network Characterization of Metallurgical Coke and Its Influence on Stress Concentration Behavior
The mechanical strength of metallurgical coke is strongly affected by its internal pore structure; however, the influence of three-dimensional pore network connectivity on stress concentration behavior remains unclear. In this study, the relationship between three-dimensional pore network structures and mechanical response in metallurgical coke was investigated by combining X-ray computed tomography (CT), pore network analysis, and finite element method (FEM)–based stress analysis. Three-dimensional coke models reconstructed from X-ray CT images were analyzed using the Burn method, breadth-first search, and the maximal ball method to quantify pore size, connectivity, and network structure. Uniaxial compression was simulated using voxel-based FEM to evaluate the maximum principal stress. In addition, matrix properties were examined by nanoindentation and X-ray diffraction.The results showed that a coke sample with a uniformly connected and isotropic pore network exhibited a systematic decrease in maximum principal stress with increasing pore size and relatively small stress variability. In contrast, a coke sample with an inhomogeneous and anisotropic pore network, characterized by isolated pores and insufficient throat development, showed large scatter in maximum principal stress, even for pores with similar sizes or coordination numbers. These findings indicate that stress concentration behavior is not uniquely determined by a single structural parameter but is instead influenced by the overall connectivity and spatial arrangement of the three-dimensional pore network.
- 15 August 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (9) , 982-991
Open AccessThree-dimensional Pore Network Characterization of Metallurgical Coke and Its Influence on Stress Concentration Behavior
The mechanical strength of metallurgical coke is strongly affected by its internal pore structure; however, the influence of three-dimensional pore network connectivity on stress concentration behavior remains unclear. In this study, the relationship between three-dimensional pore network structures and mechanical response in metallurgical coke was investigated by combining X-ray computed tomography (CT), pore network analysis, and finite element method (FEM)–based stress analysis. Three-dimensional coke models reconstructed from X-ray CT images were analyzed using the Burn method, breadth-first search, and the maximal ball method to quantify pore size, connectivity, and network structure. Uniaxial compression was simulated using voxel-based FEM to evaluate the maximum principal stress. In addition, matrix properties were examined by nanoindentation and X-ray diffraction.The results showed that a coke sample with a uniformly connected and isotropic pore network exhibited a systematic decrease in maximum principal stress with increasing pore size and relatively small stress variability. In contrast, a coke sample with an inhomogeneous and anisotropic pore network, characterized by isolated pores and insufficient throat development, showed large scatter in maximum principal stress, even for pores with similar sizes or coordination numbers. These findings indicate that stress concentration behavior is not uniquely determined by a single structural parameter but is instead influenced by the overall connectivity and spatial arrangement of the three-dimensional pore network.
- Open Access
- 21 July 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 338
Three-dimensional reconstruction framework for a static liquid-jet model using SfM–MVS and surface-texture characterization
- 21 July 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 338
Open AccessThree-dimensional reconstruction framework for a static liquid-jet model using SfM–MVS and surface-texture characterization
- Open Access
- 13 July 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 337
Gas–liquid flow characteristics in random packed columns with different packing diameters for a pressure-swing desorber
- 13 July 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 337
Open AccessGas–liquid flow characteristics in random packed columns with different packing diameters for a pressure-swing desorber
- Open Access
- 4 July 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 336
Three-dimensional behavior of a liquid jet in gas crossflow under an electric field using depth-from-defocus imaging
- 4 July 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 336
Open AccessThree-dimensional behavior of a liquid jet in gas crossflow under an electric field using depth-from-defocus imaging
- Open Access
- 20 April 2026
- Published by The Japan Institute of Energy in Journal of the Japan Institute of Energy
- Vol. 105 (4) , 85-95
Numerical Analysis of CO2 Deposition in a Sublimation Tank and Evaluation of Property Parameter Effects
CO2 deposition under low-pressure conditions plays a key role in sublimation-based CO2 separation processes; however, numerical studies on this phenomenon remain limited. In this study, CO2 deposition behavior was investigated using a combination of a global tank-scale model and a local model that resolves the growth of the dry-ice layer. The global model evaluated heat transfer and fluid flow inside the tank using CO2 properties corresponding to 100 kPa and 1 kPa, while the local model analyzed the growth of the deposited layer and its influence on the near-wall temperature. Experiments conducted under reduced-pressure conditions provided two key datasets—the temporal evolution of gas temperature near the cold plate and the growth of the dry-ice layer—which were used as reference indicators for comparison with the simulations. Although the simulations reproduced the initial temperature decrease, they failed to capture the subsequent temperature rise observed experimentally, suggesting that heat release associated with CO2 deposition significantly affects the thermal behavior. When this heat release was incorporated as an additional boundary condition, the characteristic temperature rise observed in the experiments was successfully reproduced. These results clarify the respective roles and limitations of the global and local models in representing CO2 deposition behavior and provide guidance for developing more accurate numerical models.
- 20 April 2026
- Published by The Japan Institute of Energy in Journal of the Japan Institute of Energy
- Vol. 105 (4) , 85-95
Open AccessNumerical Analysis of CO2 Deposition in a Sublimation Tank and Evaluation of Property Parameter Effects
CO2 deposition under low-pressure conditions plays a key role in sublimation-based CO2 separation processes; however, numerical studies on this phenomenon remain limited. In this study, CO2 deposition behavior was investigated using a combination of a global tank-scale model and a local model that resolves the growth of the dry-ice layer. The global model evaluated heat transfer and fluid flow inside the tank using CO2 properties corresponding to 100 kPa and 1 kPa, while the local model analyzed the growth of the deposited layer and its influence on the near-wall temperature. Experiments conducted under reduced-pressure conditions provided two key datasets—the temporal evolution of gas temperature near the cold plate and the growth of the dry-ice layer—which were used as reference indicators for comparison with the simulations. Although the simulations reproduced the initial temperature decrease, they failed to capture the subsequent temperature rise observed experimentally, suggesting that heat release associated with CO2 deposition significantly affects the thermal behavior. When this heat release was incorporated as an additional boundary condition, the characteristic temperature rise observed in the experiments was successfully reproduced. These results clarify the respective roles and limitations of the global and local models in representing CO2 deposition behavior and provide guidance for developing more accurate numerical models.
- 22 January 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 325
Numerical analysis of gas–liquid countercurrent flow in a pressure-swing CO2 desorber operated at reduced pressure
- 22 January 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 325
Numerical analysis of gas–liquid countercurrent flow in a pressure-swing CO2 desorber operated at reduced pressure
- Open Access
- 7 January 2026
- Published by Wiley in Chemical Engineering & Technology
- Vol. 49 (1)
Effects of Triangular Nozzle Geometry on the Deformation and Breakup of Liquid Jets in Crossflow
Liquid‐jet deformation and breakup in crossflow underpin atomization processes (e.g., automotive spray painting). Three‐dimensional simulations were conducted for Newtonian (NW) and shear‐thinning (SV) jets ejected from triangular (tip‐forward: TS, vertex‐up: TV) and circular (CR) nozzles. The TS jet was highly unstable and broke up rapidly, whereas TV and CR jets were relatively stable. At u G = 10.0 m/s, the jet height at x = 1.5 mm for CR dropped from 0.540 (NW) to 0.152 mm (SV), showing that shear‐thinning behavior promotes breakup even in stable geometries. The aerodynamic energy received by the TS jet was about 1.5 times that of the CR jet in the NW case, whereas the SV jet retained only about 13%, demonstrating the coupled effects of geometry and rheology on jet instability. These findings provide quantitative guidelines for nozzle design and operating conditions in atomization systems handling non‐Newtonian fluids.
- 7 January 2026
- Published by Wiley in Chemical Engineering & Technology
- Vol. 49 (1)
Open AccessEffects of Triangular Nozzle Geometry on the Deformation and Breakup of Liquid Jets in Crossflow
Liquid‐jet deformation and breakup in crossflow underpin atomization processes (e.g., automotive spray painting). Three‐dimensional simulations were conducted for Newtonian (NW) and shear‐thinning (SV) jets ejected from triangular (tip‐forward: TS, vertex‐up: TV) and circular (CR) nozzles. The TS jet was highly unstable and broke up rapidly, whereas TV and CR jets were relatively stable. At u G = 10.0 m/s, the jet height at x = 1.5 mm for CR dropped from 0.540 (NW) to 0.152 mm (SV), showing that shear‐thinning behavior promotes breakup even in stable geometries. The aerodynamic energy received by the TS jet was about 1.5 times that of the CR jet in the NW case, whereas the SV jet retained only about 13%, demonstrating the coupled effects of geometry and rheology on jet instability. These findings provide quantitative guidelines for nozzle design and operating conditions in atomization systems handling non‐Newtonian fluids.
- 29 October 2025
- Published by Elsevier in Next Research
- Vol. 2 (4)
Influence of bell-cup design and operational parameters on liquid film behavior in rotary atomizers
- 29 October 2025
- Published by Elsevier in Next Research
- Vol. 2 (4)
Influence of bell-cup design and operational parameters on liquid film behavior in rotary atomizers
- Open Access
- 27 August 2025
- Published by Elsevier in Chemical Engineering Science
- Vol. 320
Three-dimensional tracking and modeling of flake particle migration during droplet impact
- 27 August 2025
- Published by Elsevier in Chemical Engineering Science
- Vol. 320
Open AccessThree-dimensional tracking and modeling of flake particle migration during droplet impact
- Open Access
- 15 August 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (9) , 1239-1246
Finite Element Analysis of Bubble Growth and Particle Swelling during Coal Pyrolysis
This study develops a finite element-based numerical model to analyze the swelling behavior of coal particles during pyrolysis. The model incorporates volatile matter release, gas diffusion, viscoelastic deformation of the coal matrix, and internal bubble pressure to reproduce realistic deformation. Simulations on single coal particles revealed non-uniform swelling, with expansion concentrated in the central region where the matrix is thinner and softer, and suppressed near the particle edges due to higher stiffness. To evaluate the influence of coal properties, the model was applied to various coal types. The results showed clear differences in swelling behavior depending on volatile content and rheological properties. Coals with higher plasticity and volatile yield exhibited earlier and more pronounced expansion, while non-caking coals showed limited swelling and high internal pressure due to their high viscosity. This indicates that both volatile generation characteristics and the temperature-dependent mechanical properties of the coal matrix play key roles in determining swelling behavior. The proposed model provides a useful tool for quantitatively evaluating deformation mechanisms in coal particles and may contribute to the optimization of pore structure in coke manufacturing for ironmaking applications.
- 15 August 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (9) , 1239-1246
Open AccessFinite Element Analysis of Bubble Growth and Particle Swelling during Coal Pyrolysis
This study develops a finite element-based numerical model to analyze the swelling behavior of coal particles during pyrolysis. The model incorporates volatile matter release, gas diffusion, viscoelastic deformation of the coal matrix, and internal bubble pressure to reproduce realistic deformation. Simulations on single coal particles revealed non-uniform swelling, with expansion concentrated in the central region where the matrix is thinner and softer, and suppressed near the particle edges due to higher stiffness. To evaluate the influence of coal properties, the model was applied to various coal types. The results showed clear differences in swelling behavior depending on volatile content and rheological properties. Coals with higher plasticity and volatile yield exhibited earlier and more pronounced expansion, while non-caking coals showed limited swelling and high internal pressure due to their high viscosity. This indicates that both volatile generation characteristics and the temperature-dependent mechanical properties of the coal matrix play key roles in determining swelling behavior. The proposed model provides a useful tool for quantitatively evaluating deformation mechanisms in coal particles and may contribute to the optimization of pore structure in coke manufacturing for ironmaking applications.