Srinivasan Jagannathan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Srinivasan Jagannathan has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Govindaraju Rajkumar
Department of Fashion Technology, Kumaraguru College of Technology, Coimbatore, India
2 shared publications - Chidamabaram Prakash
Department of Handloom and Textile Technology, Indian Institute of Handloom Technology, Ministry of Textiles, Govt. of India, Fulia, Shantipur, India
1 shared publication Mohanbharathi Chinnasamy
Kumaraguru College of Technology, Coimbatore, Tamil Nadu INDIA
1 shared publicationP. Kandhavadivu
Kumaraguru College of Technology, Coimbatore, Tamil Nadu INDIA
1 shared publication- Prabu K
Indian Institute of Handloom Technology
1 shared publication - S Udhayamarthandan
Textile Processing, SSM Polytechnic College, Tamil Nadu, India
1 shared publication
Latest Publications
- 1 July 2026
- Published by Tekstil Ve Konfeksiyon in TEKSTİL VE KONFEKSİYON
- Vol. 36 (2) , 122-129
Design and Development of Nonwoven Filters and Back Pressure Analysis Using Computational Fluid Dynamics
This study dealt with Computational Fluid Dynamics carried out for two newly developed wall-flow filters as parallel and star structures inside a Catalytic Converter present in the exhaust manifold. Further, they studied along with optimised nonwoven filter media inserted inside them to analyse the back pressure formed during exhaust filtration process. The total volume of filters along with the Diesel Oxidation Catalyst (DOC) covered a volume of 1100cc inside the Catalytic Converter in the exhaust system. However, as per existing studies, to maintain the ratio between the filter including DOC to the Catalytic Converter (CC) as 1:3, the model of Catalytic Converter developed with a volume of 3316.6cc in such a way that it has three times the volume and to ensure the free flow of exhaust gas through the system. The whole exhaust system examined with an exhaust air velocity of 26.2 m/s with 70% porosity and 80% porosity and found that the back pressure measurement attained were 27.83 kPa and 26.73 kPa, respectively. These designs revealed that they were within limit and can be utilised for filtration, where the back pressure limitations can be up to 50 kPa for up to 5kW engines.
- 1 July 2026
- Published by Tekstil Ve Konfeksiyon in TEKSTİL VE KONFEKSİYON
- Vol. 36 (2) , 122-129
Design and Development of Nonwoven Filters and Back Pressure Analysis Using Computational Fluid Dynamics
This study dealt with Computational Fluid Dynamics carried out for two newly developed wall-flow filters as parallel and star structures inside a Catalytic Converter present in the exhaust manifold. Further, they studied along with optimised nonwoven filter media inserted inside them to analyse the back pressure formed during exhaust filtration process. The total volume of filters along with the Diesel Oxidation Catalyst (DOC) covered a volume of 1100cc inside the Catalytic Converter in the exhaust system. However, as per existing studies, to maintain the ratio between the filter including DOC to the Catalytic Converter (CC) as 1:3, the model of Catalytic Converter developed with a volume of 3316.6cc in such a way that it has three times the volume and to ensure the free flow of exhaust gas through the system. The whole exhaust system examined with an exhaust air velocity of 26.2 m/s with 70% porosity and 80% porosity and found that the back pressure measurement attained were 27.83 kPa and 26.73 kPa, respectively. These designs revealed that they were within limit and can be utilised for filtration, where the back pressure limitations can be up to 50 kPa for up to 5kW engines.
- 23 January 2019
- Published by SAGE Publications in Textile Research Journal
- Vol. 89 (19-20) , 3937-3948
Integrated enzymatic and chemical treatment for single-stage preparation of cotton fabrics
Starch sized 100% cotton woven fabrics need desizing, scouring and bleaching treatments prior to coloration and finishing. Traditionally, alpha-amylase-based enzymatic desizing and combined scouring and bleaching with an alkali, surfactant and H2O2 are used. Constant research is conducted on combining the desizing, scouring and bleaching processes into a single step by many researchers. This paper aims at combining enzymatic desizing and alkaline H2O2 scouring cum bleaching with a surfactant and stabilizer. The treatment resulted in efficient desizing, scouring and bleaching, leading to excellent size removal, absorbency, seed/mote removal and whiteness index levels, and comparable tensile and tear strength levels to that of the two-step process. The dyeability aspects were comparable in terms of surface color strength ( K/ S), color difference ( ΔE) and fastness ratings. Around 50–75% savings in water, energy, power, time and effluent generation were reported. The chemical oxygen demand, biological oxygen demand, total dissolved solids, pH and turbidity values of the resulting effluent were found to be remarkably lower. The technology was also tested industrially and found to be successful.
- 23 January 2019
- Published by SAGE Publications in Textile Research Journal
- Vol. 89 (19-20) , 3937-3948
Integrated enzymatic and chemical treatment for single-stage preparation of cotton fabrics
Starch sized 100% cotton woven fabrics need desizing, scouring and bleaching treatments prior to coloration and finishing. Traditionally, alpha-amylase-based enzymatic desizing and combined scouring and bleaching with an alkali, surfactant and H2O2 are used. Constant research is conducted on combining the desizing, scouring and bleaching processes into a single step by many researchers. This paper aims at combining enzymatic desizing and alkaline H2O2 scouring cum bleaching with a surfactant and stabilizer. The treatment resulted in efficient desizing, scouring and bleaching, leading to excellent size removal, absorbency, seed/mote removal and whiteness index levels, and comparable tensile and tear strength levels to that of the two-step process. The dyeability aspects were comparable in terms of surface color strength ( K/ S), color difference ( ΔE) and fastness ratings. Around 50–75% savings in water, energy, power, time and effluent generation were reported. The chemical oxygen demand, biological oxygen demand, total dissolved solids, pH and turbidity values of the resulting effluent were found to be remarkably lower. The technology was also tested industrially and found to be successful.
- 31 August 2016
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 47 (5) , 602-621
Optimization of mechanical properties of silk fiber-reinforced polypropylene composite using Box–Behnken experimental design
In this study, the compression molding process parameters for the development of silk fiber-reinforced polypropylene composites was optimized using Box–Behnken experimental Design with response surface methodology. The trimmed silk fibers from shuttleless loom silk selvedge waste were used as reinforcement in polypropylene fiber matrix. The process parameters of compression molding such as temperature (165–185℃), time (7–15 min) and pressure (35–45 bar) were optimized with respect to the mechanical properties of the silk fiber-reinforced polypropylene composite. The optimum parameters for better mechanical properties were found to be temperature, 180℃; time, 7 min, and pressure, 35 bar in compression molding. The optimised level of parameters has shown good response to the predicted model.
- 31 August 2016
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 47 (5) , 602-621
Optimization of mechanical properties of silk fiber-reinforced polypropylene composite using Box–Behnken experimental design
In this study, the compression molding process parameters for the development of silk fiber-reinforced polypropylene composites was optimized using Box–Behnken experimental Design with response surface methodology. The trimmed silk fibers from shuttleless loom silk selvedge waste were used as reinforcement in polypropylene fiber matrix. The process parameters of compression molding such as temperature (165–185℃), time (7–15 min) and pressure (35–45 bar) were optimized with respect to the mechanical properties of the silk fiber-reinforced polypropylene composite. The optimum parameters for better mechanical properties were found to be temperature, 180℃; time, 7 min, and pressure, 35 bar in compression molding. The optimised level of parameters has shown good response to the predicted model.
- 1 September 2014
- Published by SAGE Publications in Journal of Engineered Fibers and Fabrics
- Vol. 9 (3)
Optimization of Process Parameters for Fabrication of Wool Fiber-Reinforced Polypropylene Composites with Respect to Mechanical Properties
The present study focused optimizing the process parameters of compression molding with respect to mechanical properties for fabrication of wool fiber-reinforced polypropylene composites. An experiment was designed using the Box-Behnken method with three levels and three variables using temperature, time, and pressure, as independent variables and tensile, flexural, and impact strengths as dependent variables. The process conditions were optimized using response surface methodology with the Box-Behnken experimental design. Regression equations were obtained to analyze tensile strength, flexural strength, and impact strength and the optimum process parameters were identified. The results show that the optimum conditions for compression molding are 176°C, 7 min, and 35 bar.
- 1 September 2014
- Published by SAGE Publications in Journal of Engineered Fibers and Fabrics
- Vol. 9 (3)
Optimization of Process Parameters for Fabrication of Wool Fiber-Reinforced Polypropylene Composites with Respect to Mechanical Properties
The present study focused optimizing the process parameters of compression molding with respect to mechanical properties for fabrication of wool fiber-reinforced polypropylene composites. An experiment was designed using the Box-Behnken method with three levels and three variables using temperature, time, and pressure, as independent variables and tensile, flexural, and impact strengths as dependent variables. The process conditions were optimized using response surface methodology with the Box-Behnken experimental design. Regression equations were obtained to analyze tensile strength, flexural strength, and impact strength and the optimum process parameters were identified. The results show that the optimum conditions for compression molding are 176°C, 7 min, and 35 bar.