Carlos Ferreira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Carlos Ferreira has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Beatriz Borges
Instituto de Telecomunicações, Lisbon, Portugal
7 shared publications - Henrique J. O. Pinho
Polytechnic Institute of Tomar
4 shared publications - Manuel Barros
Instituto Politécnico de Tomar
4 shared publications - Hugo Ribeiro
Instituto de Telecomunicações, Avenida Rovisco Pais, 1049-001, Lisboa, Portugal
3 shared publications - Dina M. R. Mateus
Instituto Politécnico de Tomar
2 shared publications - Hugo Marques
Instituto Superior Técnico, Av. Rovisco Pais 1, 1049 - 001 Lisboa, Portugal
2 shared publications
Latest Publications
- 28 March 2025
- Published by Springer Nature
- p. 14-26
Development of a Smart Framework to Continuously Monitor Constructed Wetland Efficiency
- 28 March 2025
- Published by Springer Nature
- p. 14-26
Development of a Smart Framework to Continuously Monitor Constructed Wetland Efficiency
- 11 June 2023
- Published by Springer Nature
- p. 189-197
Smart Monitoring of Constructed Wetlands to Improve Efficiency and Water Quality
- 11 June 2023
- Published by Springer Nature
- p. 189-197
Smart Monitoring of Constructed Wetlands to Improve Efficiency and Water Quality
- 30 September 2019
- Published by UK Zhende Publishing Limited Company in Renewable Energy and Power Quality Journal
- Vol. 17 (3)
Study of the requirements of an autonomous system for surface water quality monitoring
In recent years, there has been increasing awareness of the preservation, protection and sustainable use of natural resources. Water resources, being one of the most important natural resources, face major threats due to contamination by pollutants of various types and origins. Maintaining the quality of water resources requires more robust, reliable and more frequent monitoring than traditional techniques of data collection based on sporadic, discontinuous and manual processes. The management of large geographical areas, the insufficient spatiotemporal discretization of the values of samples collected by traditional processes and the unpredictability of natural phenomena, require a new approach to data collection procedures. This article, which is the result of ongoing research, defines the technical requirements and technologies used in a continuous and regular monitoring of surface water quality in freshwater systems, whose data acquisition system helps to identify the sources of pollution and the contaminants flow along the waterways. The design of a versatile real-time water quality monitoring system, which, due to its environmental constraints should be based on renewable energies and wireless transfer of energy, will contribute to improve the management and effective protection of water resources.
- 30 September 2019
- Published by UK Zhende Publishing Limited Company in Renewable Energy and Power Quality Journal
- Vol. 17 (3)
Study of the requirements of an autonomous system for surface water quality monitoring
In recent years, there has been increasing awareness of the preservation, protection and sustainable use of natural resources. Water resources, being one of the most important natural resources, face major threats due to contamination by pollutants of various types and origins. Maintaining the quality of water resources requires more robust, reliable and more frequent monitoring than traditional techniques of data collection based on sporadic, discontinuous and manual processes. The management of large geographical areas, the insufficient spatiotemporal discretization of the values of samples collected by traditional processes and the unpredictability of natural phenomena, require a new approach to data collection procedures. This article, which is the result of ongoing research, defines the technical requirements and technologies used in a continuous and regular monitoring of surface water quality in freshwater systems, whose data acquisition system helps to identify the sources of pollution and the contaminants flow along the waterways. The design of a versatile real-time water quality monitoring system, which, due to its environmental constraints should be based on renewable energies and wireless transfer of energy, will contribute to improve the management and effective protection of water resources.
- Open Access
- 16 April 2019
- Published by Springer Nature
- p. 266-272
Towards a Practical and Cost-Effective Water Monitoring System
- 16 April 2019
- Published by Springer Nature
- p. 266-272
Open AccessTowards a Practical and Cost-Effective Water Monitoring System
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2105-2108
New phase shift modulator for resonant converters
Resonant converters are important in the search for high efficiency energy use and low electromagnetic interference (EMI). In this paper, nonlinarities of the traditional phase shift modulator (PSM) application to resonant converters are addressed. A new modulator topology, suited for resonant converters, is proposed. It allows input-to-output linearity, bipolar input signals, and cumulatively a sinusoidal carrier, that can be achieved by filtration of any other pre-existent wave. A prototype has been constructed and experimental results are presented, showing the feasibility of the proposed modulator.
- 1 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2105-2108
New phase shift modulator for resonant converters
Resonant converters are important in the search for high efficiency energy use and low electromagnetic interference (EMI). In this paper, nonlinarities of the traditional phase shift modulator (PSM) application to resonant converters are addressed. A new modulator topology, suited for resonant converters, is proposed. It allows input-to-output linearity, bipolar input signals, and cumulatively a sinusoidal carrier, that can be achieved by filtration of any other pre-existent wave. A prototype has been constructed and experimental results are presented, showing the feasibility of the proposed modulator.
- 1 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 3413-3418
Full-bridge single-stage PFC with reduced DC bus capacitor and improved light load operation as a solution for modern SMPS
Modern Single-Stage Switch Mode Power Supplies (namely Full-Bridge topologies for high power applications >500W), allows to regulate the output voltage and the input current, achieving a sinusoidal waveform by using only the four bridge transistors. However, these solutions still need to be optimized in order to become an interesting and attractive solution for modern Switch Mode Power Supplies with PFC function. One of the most important improvements needed is the downsizing and the cost reduction associated to the DC bus capacitor (C F - filtering capacitor). Nevertheless, this action introduces several complex issues in the regulation of the input current and also high output voltage ripple. The proposed paper describes a new process to reduce the C F value solving the identified issues. Firstly it is proved that it is possible to use a reduced capacitance/watt ratio, lower than the one that is typically used in commercial applications 0.5μF/W, while maintaining the accurate regulation of the input current. The output voltage ripple issues are solved using a modified One Cycle Control, OCC circuit. The concepts and solutions developed will be proved based on experimental results in an optimized FBSS topology that uses a Free Wheeling Capacitor, FWC, circuit in order to improve the low power operation.
- 1 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 3413-3418
Full-bridge single-stage PFC with reduced DC bus capacitor and improved light load operation as a solution for modern SMPS
Modern Single-Stage Switch Mode Power Supplies (namely Full-Bridge topologies for high power applications >500W), allows to regulate the output voltage and the input current, achieving a sinusoidal waveform by using only the four bridge transistors. However, these solutions still need to be optimized in order to become an interesting and attractive solution for modern Switch Mode Power Supplies with PFC function. One of the most important improvements needed is the downsizing and the cost reduction associated to the DC bus capacitor (C F - filtering capacitor). Nevertheless, this action introduces several complex issues in the regulation of the input current and also high output voltage ripple. The proposed paper describes a new process to reduce the C F value solving the identified issues. Firstly it is proved that it is possible to use a reduced capacitance/watt ratio, lower than the one that is typically used in commercial applications 0.5μF/W, while maintaining the accurate regulation of the input current. The output voltage ripple issues are solved using a modified One Cycle Control, OCC circuit. The concepts and solutions developed will be proved based on experimental results in an optimized FBSS topology that uses a Free Wheeling Capacitor, FWC, circuit in order to improve the low power operation.
- 16 November 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 60 (5) , 2074-2083
Sine-Wave Amplitude-Modulation Concept for Linear Behavior of Phase-Modulated Resonant Converters
This paper focuses on a dc-ac resonant power converter using a special sine-wave amplitude-modulation concept with the objective of achieving a linear input-output behavior, low harmonic content at the output, and reduced stages number. This technique can be applied to a wide range of resonant converters' applications. Sine-wave generation techniques and phase-modulation method limitations are analyzed. Alternative solutions, such as a new predistorted phase modulator, are developed. A prototype was designed and implemented. Presented experimental results demonstrate the effectiveness of the presented principle.
- 16 November 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 60 (5) , 2074-2083
Sine-Wave Amplitude-Modulation Concept for Linear Behavior of Phase-Modulated Resonant Converters
This paper focuses on a dc-ac resonant power converter using a special sine-wave amplitude-modulation concept with the objective of achieving a linear input-output behavior, low harmonic content at the output, and reduced stages number. This technique can be applied to a wide range of resonant converters' applications. Sine-wave generation techniques and phase-modulation method limitations are analyzed. Alternative solutions, such as a new predistorted phase modulator, are developed. A prototype was designed and implemented. Presented experimental results demonstrate the effectiveness of the presented principle.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1101-1107
A family of Full-Bridge Single-Stage PFCs topologies: Identification of technical problems
In order to provide AC-DC conversion and power factor correction (PFC), Full-Bridge Single-Stage (FBSS) topologies are the most popular for high performance converters with power levels above 500W. Their behaviour and features are in general well defined and analysed. However, these topologies may introduce several complex operating limits and control problems that are not yet described in literature. This is mainly due to the fact that these limitations devaluate and restrict the number of applications. The most concerning problems are identified as: transformer primary saturation and output voltage perturbations. Wide load range variation can also be considered a complex issue because it leads to uncontrollable circuit variables, namely, input current and DC bus voltage. With the objective of clarification, this paper analyses in detail the referred technical problems considering their impact in the FBSS topologies operation and presents design criteria and control solutions to minimize their effects. Experimental results are presented to verify the theoretical concepts.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1101-1107
A family of Full-Bridge Single-Stage PFCs topologies: Identification of technical problems
In order to provide AC-DC conversion and power factor correction (PFC), Full-Bridge Single-Stage (FBSS) topologies are the most popular for high performance converters with power levels above 500W. Their behaviour and features are in general well defined and analysed. However, these topologies may introduce several complex operating limits and control problems that are not yet described in literature. This is mainly due to the fact that these limitations devaluate and restrict the number of applications. The most concerning problems are identified as: transformer primary saturation and output voltage perturbations. Wide load range variation can also be considered a complex issue because it leads to uncontrollable circuit variables, namely, input current and DC bus voltage. With the objective of clarification, this paper analyses in detail the referred technical problems considering their impact in the FBSS topologies operation and presents design criteria and control solutions to minimize their effects. Experimental results are presented to verify the theoretical concepts.
- 1 November 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 845-849
New modular two stage switching converter for high power stereo audio amplifier
This paper proposes a novel topology of a two independent channel switched audio high power amplifier. A three-branch inverter, two high frequency isolation transformers, two output high frequency cycloconverters and two low-pass filters, compose the basic topology. This architecture has the advantage that the inverter middle branch is common to both channels of the amplifier, without compromising the channel independency, and reducing the number of devices. The objective is to obtain a compact, high power density and reliable system. This Single Conversion Stage Amplifier topology integrates in a single unit both the power supply and the D-class amplifier, conferring to the total system direct and more efficient power conversion and compactness due to the component reduction. Since the amplifier outputs are totally isolated, modular operation is possible among several amplifier units or even between the two channels of a same unit. The amplifier output filter specifications could be relaxed because the principle of operation duplicates the equivalent switching frequency. Another advantage is that the output cycloconverters switch with zero voltage, reducing switching losses. The proposed topology is described and analysed, with emphasis in the principle of operation, modulation techniques and design criteria. The experimental results verify the theoretical analysis.
- 1 November 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 845-849
New modular two stage switching converter for high power stereo audio amplifier
This paper proposes a novel topology of a two independent channel switched audio high power amplifier. A three-branch inverter, two high frequency isolation transformers, two output high frequency cycloconverters and two low-pass filters, compose the basic topology. This architecture has the advantage that the inverter middle branch is common to both channels of the amplifier, without compromising the channel independency, and reducing the number of devices. The objective is to obtain a compact, high power density and reliable system. This Single Conversion Stage Amplifier topology integrates in a single unit both the power supply and the D-class amplifier, conferring to the total system direct and more efficient power conversion and compactness due to the component reduction. Since the amplifier outputs are totally isolated, modular operation is possible among several amplifier units or even between the two channels of a same unit. The amplifier output filter specifications could be relaxed because the principle of operation duplicates the equivalent switching frequency. Another advantage is that the output cycloconverters switch with zero voltage, reducing switching losses. The proposed topology is described and analysed, with emphasis in the principle of operation, modulation techniques and design criteria. The experimental results verify the theoretical analysis.
- 1 June 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 1905-1911
New notch low pass filter for use in switching audio amplification
In this paper a novel switched audio amplifier filter topology is proposed and its design criteria are presented. It permits improved attenuation of the switching frequency components and load impedance variation with very low gain variation in the audio band. The new filter configuration allows the use of simple converter topologies while obtaining the same output voltage ripple levels as in multilevel converters. The construction of a prototype is addressed and experimental results are presented, showing the feasibility of the proposed method.
- 1 June 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 1905-1911
New notch low pass filter for use in switching audio amplification
In this paper a novel switched audio amplifier filter topology is proposed and its design criteria are presented. It permits improved attenuation of the switching frequency components and load impedance variation with very low gain variation in the audio band. The new filter configuration allows the use of simple converter topologies while obtaining the same output voltage ripple levels as in multilevel converters. The construction of a prototype is addressed and experimental results are presented, showing the feasibility of the proposed method.