Ánxela Fernández-Naveira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ánxela Fernández-Naveira has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Christian Kennes
Chemical Engineering Laboratory, Faculty of Sciences and Interdisciplinary Centre of Chemistry and Biology - Centro Interdisciplinar de Química y Biología (CICA), BIOENGIN group, University of La Coruña (UDC), E-15008 La Coruña, Spain
6 shared publications - Maria Carmen Veiga
Chemical Engineering Laboratory, Faculty of Sciences and Interdisciplinary Center for Chemistry and Biology (CICA), University of Coruña, Rúa da Fraga 10, 15008 A Coruña, Spain
5 shared publications - Haris Nalakath Abubackar
Chemical Engineering Laboratory, Faculty of Sciences, University of La Coruña, Rúa da Fraga 10, 15008 La Coruña, Spain
4 shared publications - Carmen Rioboo
Laboratorio de Microbiología, Facultad de Ciencias, Universidade da Coruña, Campus da Zapateira s/n, 15071 A Coruña, Spain
1 shared publication - Concepción Herrero
Laboratorio de Microbiología, Facultad de Ciencias, Universidad de A Coruña, Campus de A Zapateira s/n, 15071 A Coruña, Spain
1 shared publication María C. Veiga
1 shared publication
Latest Publications
- 6 March 2017
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 92 (6) , 1178-1185
Effect of pH control on the anaerobic H‐B‐E fermentation of syngas in bioreactors
BACKGROUND: Syngas and some waste gases are composed mainly of carbon monoxide, carbon dioxide and hydrogen, which can be used by some acetogenic bacteria to produce ethanol, butanol or hexanol, and represents an attractive alternative to the conventional ABE (acetone–butanol–ethanol) fermentation. Experiments were carried out in bioreactors under different conditions (pH 5.75 and 4.75) with continuous supply of a mixture of CO/CO2/H2/N2 converted by Clostridium carboxidivorans into hexanol, butanol and ethanol (H‐B‐E fermentation).RESULTS: Applying different pH control strategies will affect the syngas fermentation pattern, among others in terms of bioconversion rates as well as final concentrations of acids and alcohols. The highest concentrations of alcohols were obtained at pH 5.75, i.e. 2.7 g L−1 ethanol, 1.9 g L−1 butanol and 0.85 g L−1 hexanol, whereas the maximum production rates were observed at pH 4.75, reaching 0.048 g‐ethanol h−1 g−1‐biomass, 0.037 g‐butanol h−1 g−1‐biomass, and 0.026 g‐hexanol h−1 g−1‐biomass. However, a low pH negatively affects growth and acids production in the first metabolic step, with lower growth and acids production at pH 4.75 than 5.75. Growth rates reached 0.0057 h−1 and 0.072 h−1, respectively, at pH 4.75 and 5.75.CONCLUSIONS: Maintaining initially a higher pH of 5.75 allows accumulating higher concentrations of acids than when natural acidification takes place. Such higher concentrations of acids allow the production of higher amounts of alcohols as end metabolites, showing the importance of pH on bioconversion and biomass growth. © 2017 Society of Chemical Industry
- 6 March 2017
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 92 (6) , 1178-1185
Effect of pH control on the anaerobic H‐B‐E fermentation of syngas in bioreactors
BACKGROUND: Syngas and some waste gases are composed mainly of carbon monoxide, carbon dioxide and hydrogen, which can be used by some acetogenic bacteria to produce ethanol, butanol or hexanol, and represents an attractive alternative to the conventional ABE (acetone–butanol–ethanol) fermentation. Experiments were carried out in bioreactors under different conditions (pH 5.75 and 4.75) with continuous supply of a mixture of CO/CO2/H2/N2 converted by Clostridium carboxidivorans into hexanol, butanol and ethanol (H‐B‐E fermentation).RESULTS: Applying different pH control strategies will affect the syngas fermentation pattern, among others in terms of bioconversion rates as well as final concentrations of acids and alcohols. The highest concentrations of alcohols were obtained at pH 5.75, i.e. 2.7 g L−1 ethanol, 1.9 g L−1 butanol and 0.85 g L−1 hexanol, whereas the maximum production rates were observed at pH 4.75, reaching 0.048 g‐ethanol h−1 g−1‐biomass, 0.037 g‐butanol h−1 g−1‐biomass, and 0.026 g‐hexanol h−1 g−1‐biomass. However, a low pH negatively affects growth and acids production in the first metabolic step, with lower growth and acids production at pH 4.75 than 5.75. Growth rates reached 0.0057 h−1 and 0.072 h−1, respectively, at pH 4.75 and 5.75.CONCLUSIONS: Maintaining initially a higher pH of 5.75 allows accumulating higher concentrations of acids than when natural acidification takes place. Such higher concentrations of acids allow the production of higher amounts of alcohols as end metabolites, showing the importance of pH on bioconversion and biomass growth. © 2017 Society of Chemical Industry
- 3 February 2017
- Published by Springer Nature in World Journal of Microbiology and Biotechnology
- Vol. 33 (3) , 1-11
Production of chemicals from C1 gases (CO, CO2) by Clostridium carboxidivorans
Bioprocesses in conventional second generation biorefineries are mainly based on the fermentation of sugars obtained from lignocellulosic biomass or agro-industrial wastes. An alternative to this process consists in gasifying those same feedstocks or even other carbon-containing materials to obtain syngas which can also be fermented by some anaerobic bacteria to produce chemicals or fuels. Carbon monoxide, carbon dioxide and hydrogen, which are the main components of syngas, are also found in some industrial waste gases, among others in steel industries. Clostridium carboxidivorans is able to metabolise such gases to produce ethanol and higher alcohols, i.e. butanol and hexanol, following the Wood–Ljungdahl pathway. This does simultaneously allow the removal of volatile pollutants involved in climate change. The bioconversion is a two step process in which organic acids (acetate, butyrate, hexanoate) are produced first, followed by the accumulation of alcohols; although partial overlap in time of acids and alcohols production may sometimes take place as well. Several parameters, among others pH, temperature, or gas-feed flow rates in bioreactors, affect the bioconversion process. Besides, the accumulation of high concentrations of alcohols in the fermentation broth inhibits the growth and metabolic activity of C. carboxidivorans.
- 3 February 2017
- Published by Springer Nature in World Journal of Microbiology and Biotechnology
- Vol. 33 (3) , 1-11
Production of chemicals from C1 gases (CO, CO2) by Clostridium carboxidivorans
Bioprocesses in conventional second generation biorefineries are mainly based on the fermentation of sugars obtained from lignocellulosic biomass or agro-industrial wastes. An alternative to this process consists in gasifying those same feedstocks or even other carbon-containing materials to obtain syngas which can also be fermented by some anaerobic bacteria to produce chemicals or fuels. Carbon monoxide, carbon dioxide and hydrogen, which are the main components of syngas, are also found in some industrial waste gases, among others in steel industries. Clostridium carboxidivorans is able to metabolise such gases to produce ethanol and higher alcohols, i.e. butanol and hexanol, following the Wood–Ljungdahl pathway. This does simultaneously allow the removal of volatile pollutants involved in climate change. The bioconversion is a two step process in which organic acids (acetate, butyrate, hexanoate) are produced first, followed by the accumulation of alcohols; although partial overlap in time of acids and alcohols production may sometimes take place as well. Several parameters, among others pH, temperature, or gas-feed flow rates in bioreactors, affect the bioconversion process. Besides, the accumulation of high concentrations of alcohols in the fermentation broth inhibits the growth and metabolic activity of C. carboxidivorans.
- 9 January 2017
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 92 (4) , 712-731
H‐B‐E (hexanol‐butanol‐ethanol) fermentation for the production of higher alcohols from syngas/waste gas
CO, H2, and CO2 are major components of syngas and some industrial CO‐rich waste gases (e.g. waste gases from steel industries), besides some additional minor compounds. It was recently shown that those gases can be bioconverted, by acetogenic/solventogenic bacteria, into ethanol and higher alcohols such as butanol, but also hexanol, through the so‐called HBE fermentation. That process presents some advantages over existing chemical conversion processes. This paper reviews HBE fermentation from C1‐gases after briefly describing the more conventional ABE (acetone‐butanol‐ethanol) fermentation from carbohydrates by Clostridium acetobutylicum, in order to allow for comparison of both processes. Although acetone may appear in carbohydrate fermentation, alcohols are the only major end‐metabolites in the HBE process with Clostridium carboxidivorans. The few acetogenic bacteria known to metabolize C1‐gases and produce butanol or higher alcohols are described. Clostridium carboxidivorans has been used in most cases. Bioconversion of the gaseous substrates takes place in two stages, namely acidogenesis (production of acids) followed by solventogenesis (production of alcohols), characterized by different optimal fermentation conditions. Major parameters affecting each bioconversion stage as well as the overall fermentation process are analyzed. Although it has been claimed that acidification is required in ABE fermentation to initiate the solventogenic stage, strong acidification seems to some extent not to be a prerequisite for solventogenesis in the HBE process. Bioreactors potentially suitable for this type of bioconversion process are described as well. © 2017 Society of Chemical Industry
- 9 January 2017
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 92 (4) , 712-731
H‐B‐E (hexanol‐butanol‐ethanol) fermentation for the production of higher alcohols from syngas/waste gas
CO, H2, and CO2 are major components of syngas and some industrial CO‐rich waste gases (e.g. waste gases from steel industries), besides some additional minor compounds. It was recently shown that those gases can be bioconverted, by acetogenic/solventogenic bacteria, into ethanol and higher alcohols such as butanol, but also hexanol, through the so‐called HBE fermentation. That process presents some advantages over existing chemical conversion processes. This paper reviews HBE fermentation from C1‐gases after briefly describing the more conventional ABE (acetone‐butanol‐ethanol) fermentation from carbohydrates by Clostridium acetobutylicum, in order to allow for comparison of both processes. Although acetone may appear in carbohydrate fermentation, alcohols are the only major end‐metabolites in the HBE process with Clostridium carboxidivorans. The few acetogenic bacteria known to metabolize C1‐gases and produce butanol or higher alcohols are described. Clostridium carboxidivorans has been used in most cases. Bioconversion of the gaseous substrates takes place in two stages, namely acidogenesis (production of acids) followed by solventogenesis (production of alcohols), characterized by different optimal fermentation conditions. Major parameters affecting each bioconversion stage as well as the overall fermentation process are analyzed. Although it has been claimed that acidification is required in ABE fermentation to initiate the solventogenic stage, strong acidification seems to some extent not to be a prerequisite for solventogenesis in the HBE process. Bioreactors potentially suitable for this type of bioconversion process are described as well. © 2017 Society of Chemical Industry
Impact of cyclic pH shifts on carbon monoxide fermentation to ethanol by Clostridium autoethanogenum
- 6 May 2016
- Published by Taylor & Francis in European Journal of Phycology
- Vol. 51 (3) , 338-345
Atrazine induced changes in elemental and biochemical composition and nitrate reductase activity in Chlamydomonas reinhardtii
Herbicides play an important role in agricultural practices but the introduction of these compounds into the aquatic environment can have severe consequences for non-target organisms such as microalgae. The ubiquitous green freshwater microalga Chlamydomonas reinhardtii, a model species in all aspects of microalgal physiology, was used to assess the toxicity of atrazine, one of the most widely used herbicides throughout the world. Atrazine acts on photosynthesis and therefore can affect non-target primary producers, such as microalgae. Growth, dry weight, elemental composition, photosynthetic pigments and protein contents and nitrate reductase activity were studied. After 96 h of exposure to different atrazine concentrations all the parameters studied were affected, but different sensitivities to the herbicide were shown. Nitrate reductase (NR) activity was strongly affected even at an atrazine concentration that did not affect growth (0.1 µM); the lowest concentrations of atrazine assayed (0.1 and 0.25 µM) provoked a > 40% decrease in NR activity and NR decreased > 80% with atrazine concentrations of 0.5 µM. C/N ratio was also affected by all the atrazine concentrations assayed. Nitrate reductase activity and C/N ratio were better indicators of the cellular stress state than data on other biochemical components or growth rate. Among cell parameters assayed, the NR activity stood out as a sensitive cytotoxicity endpoint and the activity of this enzyme can be suggested as a sensitive biomarker of stress induced by atrazine in C. reinhardtii.
- 6 May 2016
- Published by Taylor & Francis in European Journal of Phycology
- Vol. 51 (3) , 338-345
Atrazine induced changes in elemental and biochemical composition and nitrate reductase activity in Chlamydomonas reinhardtii
Herbicides play an important role in agricultural practices but the introduction of these compounds into the aquatic environment can have severe consequences for non-target organisms such as microalgae. The ubiquitous green freshwater microalga Chlamydomonas reinhardtii, a model species in all aspects of microalgal physiology, was used to assess the toxicity of atrazine, one of the most widely used herbicides throughout the world. Atrazine acts on photosynthesis and therefore can affect non-target primary producers, such as microalgae. Growth, dry weight, elemental composition, photosynthetic pigments and protein contents and nitrate reductase activity were studied. After 96 h of exposure to different atrazine concentrations all the parameters studied were affected, but different sensitivities to the herbicide were shown. Nitrate reductase (NR) activity was strongly affected even at an atrazine concentration that did not affect growth (0.1 µM); the lowest concentrations of atrazine assayed (0.1 and 0.25 µM) provoked a > 40% decrease in NR activity and NR decreased > 80% with atrazine concentrations of 0.5 µM. C/N ratio was also affected by all the atrazine concentrations assayed. Nitrate reductase activity and C/N ratio were better indicators of the cellular stress state than data on other biochemical components or growth rate. Among cell parameters assayed, the NR activity stood out as a sensitive cytotoxicity endpoint and the activity of this enzyme can be suggested as a sensitive biomarker of stress induced by atrazine in C. reinhardtii.
- 27 February 2016
- Published by Springer Nature in Applied Microbiology and Biotechnology
- Vol. 100 (9) , 4231-4240
Carbon monoxide bioconversion to butanol-ethanol by Clostridium carboxidivorans: kinetics and toxicity of alcohols
Butanol production from carbon monoxide-rich waste gases or syngas is an attractive novel alternative to the conventional acetone-butanol-ethanol (ABE) fermentation. Solvent toxicity is a key factor reported in ABE fermentation with carbohydrates as substrates. However, in the gas-fermentation process, kinetic aspects and the inhibition effect of solvents have not thoroughly been studied. Therefore, different batch bottle experiments were carried out with the bacterial species Clostridium carboxidivorans using CO as carbon source for butanol-ethanol fermentation. A maximum specific growth rate of 0.086 ± 0.004 h−1 and a biomass yield of 0.011 gbiomass/gCO were found, which is significantly lower than in other clostridia grown on sugars. Besides, three assays were carried out to check the inhibitory effect of butanol, ethanol, and their mixtures. Butanol had a higher inhibitory effect on the cells than ethanol and showed a lower IC50, reduced growth rate, and slower CO consumption with increasing alcohol concentrations. A concentration of 14–14.50 g/L butanol caused 50 % growth inhibition in C. carboxidivorans, and 20 g/L butanol resulted in complete inhibition, with a growth rate of 0 h−1. Conversely, 35 g/L ethanol decreased by 50 % the final biomass concentration respect to the control and yielded the lowest growth rate of 0.024 h−1. The inhibitory effect of mixtures of both alcohols was also checked adding similar, near identical, concentrations of each one. Growth decreased by 50 % in the presence of a total concentration of alcohols of 16.22 g/L, consisting of similar amounts of each alcohol. Occasional differences in initially added concentrations of alcohols were minimal. The lowest growth rate (0.014 h−1) was observed at the highest concentration assayed (25 g/L).
- 27 February 2016
- Published by Springer Nature in Applied Microbiology and Biotechnology
- Vol. 100 (9) , 4231-4240
Carbon monoxide bioconversion to butanol-ethanol by Clostridium carboxidivorans: kinetics and toxicity of alcohols
Butanol production from carbon monoxide-rich waste gases or syngas is an attractive novel alternative to the conventional acetone-butanol-ethanol (ABE) fermentation. Solvent toxicity is a key factor reported in ABE fermentation with carbohydrates as substrates. However, in the gas-fermentation process, kinetic aspects and the inhibition effect of solvents have not thoroughly been studied. Therefore, different batch bottle experiments were carried out with the bacterial species Clostridium carboxidivorans using CO as carbon source for butanol-ethanol fermentation. A maximum specific growth rate of 0.086 ± 0.004 h−1 and a biomass yield of 0.011 gbiomass/gCO were found, which is significantly lower than in other clostridia grown on sugars. Besides, three assays were carried out to check the inhibitory effect of butanol, ethanol, and their mixtures. Butanol had a higher inhibitory effect on the cells than ethanol and showed a lower IC50, reduced growth rate, and slower CO consumption with increasing alcohol concentrations. A concentration of 14–14.50 g/L butanol caused 50 % growth inhibition in C. carboxidivorans, and 20 g/L butanol resulted in complete inhibition, with a growth rate of 0 h−1. Conversely, 35 g/L ethanol decreased by 50 % the final biomass concentration respect to the control and yielded the lowest growth rate of 0.024 h−1. The inhibitory effect of mixtures of both alcohols was also checked adding similar, near identical, concentrations of each one. Growth decreased by 50 % in the presence of a total concentration of alcohols of 16.22 g/L, consisting of similar amounts of each alcohol. Occasional differences in initially added concentrations of alcohols were minimal. The lowest growth rate (0.014 h−1) was observed at the highest concentration assayed (25 g/L).
- 25 January 2016
- Published by Springer Nature in Applied Microbiology and Biotechnology
- Vol. 100 (7) , 3361-3370
Efficient butanol-ethanol (B-E) production from carbon monoxide fermentation by Clostridium carboxidivorans
The fermentation of waste gases rich in carbon monoxide using acetogens is an efficient way to obtain valuable biofuels like ethanol and butanol. Different experiments were carried out with the bacterial species Clostridium carboxidivorans as biocatalyst. In batch assays with no pH regulation, after complete substrate exhaustion, acetic acid, butyric acid, and ethanol were detected while only negligible butanol production was observed. On the other side, in bioreactors, with continuous carbon monoxide supply and pH regulation, both C2 and C4 fatty acids were initially formed as well as ethanol and butanol at concentrations never reported before for this type of anaerobic bioconversion of gaseous C1 compounds, showing that the operating conditions significantly affect the metabolic fermentation profile and butanol accumulation. Maximum ethanol and butanol concentrations in the bioreactors were obtained at pH 5.75, reaching values of 5.55 and 2.66 g/L, respectively. The alcohols were produced both from CO fermentation as well as from the bioconversion of previously accumulated acetic and butyric acids, resulting in low residual concentrations of such acids at the end of the bioreactor experiments. CO consumption was often around 50 % and reached up to more than 80 %. Maximum specific rates of ethanol and butanol production were reached at pH 4.75, with values of 0.16 g/h*g of biomass and 0.07 g/h*g of biomass, respectively, demonstrating that a low pH was more favorable to solventogenesis in this process, although it negatively affects biomass growth which does also play a role in the final alcohol titer.
- 25 January 2016
- Published by Springer Nature in Applied Microbiology and Biotechnology
- Vol. 100 (7) , 3361-3370
Efficient butanol-ethanol (B-E) production from carbon monoxide fermentation by Clostridium carboxidivorans
The fermentation of waste gases rich in carbon monoxide using acetogens is an efficient way to obtain valuable biofuels like ethanol and butanol. Different experiments were carried out with the bacterial species Clostridium carboxidivorans as biocatalyst. In batch assays with no pH regulation, after complete substrate exhaustion, acetic acid, butyric acid, and ethanol were detected while only negligible butanol production was observed. On the other side, in bioreactors, with continuous carbon monoxide supply and pH regulation, both C2 and C4 fatty acids were initially formed as well as ethanol and butanol at concentrations never reported before for this type of anaerobic bioconversion of gaseous C1 compounds, showing that the operating conditions significantly affect the metabolic fermentation profile and butanol accumulation. Maximum ethanol and butanol concentrations in the bioreactors were obtained at pH 5.75, reaching values of 5.55 and 2.66 g/L, respectively. The alcohols were produced both from CO fermentation as well as from the bioconversion of previously accumulated acetic and butyric acids, resulting in low residual concentrations of such acids at the end of the bioreactor experiments. CO consumption was often around 50 % and reached up to more than 80 %. Maximum specific rates of ethanol and butanol production were reached at pH 4.75, with values of 0.16 g/h*g of biomass and 0.07 g/h*g of biomass, respectively, demonstrating that a low pH was more favorable to solventogenesis in this process, although it negatively affects biomass growth which does also play a role in the final alcohol titer.