Butsurin Jinnai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Butsurin Jinnai has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Shunsuke Fukami
Laboratory for Nanoelectronics and Spintronics, Research Institute of Electrical Communication, Tohoku University 1 , 2-1-1 Katahira, Aoba-ku, Sendai 980-8577
20 shared publications - Hideo Ohno
Tohoku University
15 shared publications - Seiji Samukawa
Institute of Communications Engineering, National Yang Ming Chiao Tung University, Hsinchu, Taiwan
14 shared publications - Junta Igarashi
National Institute of Advanced Industrial Science and Technology
11 shared publications Hiroto Ohtake
5 shared publicationsHideo Ohno
Laboratory for Nanoelectronics and Spintronics, Research Institute of Electrical Communication, Tohoku University, Sendai, Japan
4 shared publications
Latest Publications
- Open Access
- 29 October 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 26 (4)
Inhomogeneity of magnetic anisotropy and damping in nanoscale magnetic tunnel junctions
We investigate the Gilbert damping constant α and the inhomogeneity of the effective magnetic anisotropy field H K eff in nanoscale magnetic tunnel junctions (MTJs) with various free-layer diameters D , which have two different structures possessing different magnetic properties around the pattern edge. Homodyne-detected ferromagnetic resonance (FMR) is used, allowing to disentangle the inhomogeneous broadening Δ H 0 owing to the spatial variation of H K eff from the effects of damping in the linewidth of spectra. We find that Δ H 0 increases with decrease in D , while α is almost constant. The degree of the increase in Δ H 0 is found to change with the MTJ structure. We show that these results are explained by a model considering the distribution of a demagnetizing field that increases with the decrease in D . The obtained findings provide important insights for the development of nanoscale MTJs with high reliability and high efficiency.
- 29 October 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 26 (4)
Open AccessInhomogeneity of magnetic anisotropy and damping in nanoscale magnetic tunnel junctions
We investigate the Gilbert damping constant α and the inhomogeneity of the effective magnetic anisotropy field H K eff in nanoscale magnetic tunnel junctions (MTJs) with various free-layer diameters D , which have two different structures possessing different magnetic properties around the pattern edge. Homodyne-detected ferromagnetic resonance (FMR) is used, allowing to disentangle the inhomogeneous broadening Δ H 0 owing to the spatial variation of H K eff from the effects of damping in the linewidth of spectra. We find that Δ H 0 increases with decrease in D , while α is almost constant. The degree of the increase in Δ H 0 is found to change with the MTJ structure. We show that these results are explained by a model considering the distribution of a demagnetizing field that increases with the decrease in D . The obtained findings provide important insights for the development of nanoscale MTJs with high reliability and high efficiency.
- Open Access
- 1 August 2026
- Published by AIP Publishing in APL Materials
- Vol. 14 (8)
Single-shot laser-pulse-induced magnetization reversal in CoFeB/MgO-based magnetic tunnel junctions
We demonstrate single-shot laser-pulse-induced magnetization reversal in rare-earth-free CoFeB/MgO magnetic tunnel junctions (MTJs), a material system widely adopted in spin-transfer torque magnetic random-access memory. By tuning the Ru capping layer thickness, we modify the laser energy absorption profile and observe magnetization reversal from the parallel to antiparallel state, with switching observed for tRu ≥ 2.0 nm. Furthermore, we detect magnetization reversal in a micro-scale MTJ device via the tunnel magnetoresistance effect. Our findings suggest that ultrafast spin transport, dipolar interactions, or a combination of both may contribute to the switching process, although the precise mechanism remains to be clarified. This work represents a significant step toward integrating ultrafast optical control with MTJ technology.
- 1 August 2026
- Published by AIP Publishing in APL Materials
- Vol. 14 (8)
Open AccessSingle-shot laser-pulse-induced magnetization reversal in CoFeB/MgO-based magnetic tunnel junctions
We demonstrate single-shot laser-pulse-induced magnetization reversal in rare-earth-free CoFeB/MgO magnetic tunnel junctions (MTJs), a material system widely adopted in spin-transfer torque magnetic random-access memory. By tuning the Ru capping layer thickness, we modify the laser energy absorption profile and observe magnetization reversal from the parallel to antiparallel state, with switching observed for tRu ≥ 2.0 nm. Furthermore, we detect magnetization reversal in a micro-scale MTJ device via the tunnel magnetoresistance effect. Our findings suggest that ultrafast spin transport, dipolar interactions, or a combination of both may contribute to the switching process, although the precise mechanism remains to be clarified. This work represents a significant step toward integrating ultrafast optical control with MTJ technology.
- Open Access
- 21 April 2026
- Published by Springer Nature in Communications Materials
- Vol. 7 (1)
Stochastic switching time constant and instability in nanomagnets
- 21 April 2026
- Published by Springer Nature in Communications Materials
- Vol. 7 (1)
Open AccessStochastic switching time constant and instability in nanomagnets
- 24 July 2024
- Published by Springer Nature in Nature Electronics
- Vol. 7 (8) , 653-661
Nanoscale spin rectifiers for harvesting ambient radiofrequency energy
- 24 July 2024
- Published by Springer Nature in Nature Electronics
- Vol. 7 (8) , 653-661
Nanoscale spin rectifiers for harvesting ambient radiofrequency energy
- Open Access
- 4 January 2024
- Published by Springer Nature in npj Spintronics
- Vol. 2 (1) , 1-9
Single-nanometer CoFeB/MgO magnetic tunnel junctions with high-retention and high-speed capabilities
Making magnetic tunnel junctions (MTJs) smaller while meeting performance requirements is critical for future electronics with spin-transfer torque magnetoresistive random access memory (STT-MRAM). However, it is challenging in the conventional MTJs using a thin CoFeB free layer capped with an MgO layer because of increasing difficulties in satisfying the required data retention and switching speed at smaller scales. Here we report single-nanometer MTJs using a free layer consisting of CoFeB/MgO multilayers, where the number of CoFeB/MgO interfaces and/or the CoFeB thicknesses are engineered to tailor device performance to applications requiring high-data retention or high-speed capability. We fabricate ultra-small MTJs down to 2.0 nm and show high data retention (over 10 years) and high-speed switching at 10 ns or below in sub-5-nm MTJs. The stack design proposed here proves that ultra-small CoFeB/MgO MTJs hold the potential for high-performance and high-density STT-MRAM.
- 4 January 2024
- Published by Springer Nature in npj Spintronics
- Vol. 2 (1) , 1-9
Open AccessSingle-nanometer CoFeB/MgO magnetic tunnel junctions with high-retention and high-speed capabilities
Making magnetic tunnel junctions (MTJs) smaller while meeting performance requirements is critical for future electronics with spin-transfer torque magnetoresistive random access memory (STT-MRAM). However, it is challenging in the conventional MTJs using a thin CoFeB free layer capped with an MgO layer because of increasing difficulties in satisfying the required data retention and switching speed at smaller scales. Here we report single-nanometer MTJs using a free layer consisting of CoFeB/MgO multilayers, where the number of CoFeB/MgO interfaces and/or the CoFeB thicknesses are engineered to tailor device performance to applications requiring high-data retention or high-speed capability. We fabricate ultra-small MTJs down to 2.0 nm and show high data retention (over 10 years) and high-speed switching at 10 ns or below in sub-5-nm MTJs. The stack design proposed here proves that ultra-small CoFeB/MgO MTJs hold the potential for high-performance and high-density STT-MRAM.
- 21 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (2) , 184-187
Pitch Scaling Prospect of Ultra-Small Magnetic Tunnel Junctions for High-Density STT-MRAM: Effects of Magnetostatic Interference From Neighboring Bits
Magnetic tunnel junction (MTJ) miniaturization has been demonstrated down to 2 nm with performance applicable to a wide variety of applications. In highly dense STT-MRAM, where such ultra-small MTJs are packed with tight pitches, magnetostatic interference from neighboring bits becomes a concern. In this study, we investigate the impact of magnetostatic interference on the ultra-small MTJs with various stack structures when integrated in highly dense arrays and discuss the scaling prospect. We first calculate the stray fields exerted on an MTJ from neighboring bits and then evaluate the tolerance of the MTJ against the field by measuring the external field dependence of the switching voltage of isolated MTJs. We find that STT-MRAM using the ultra-small MTJs has the potential to achieve a large capacity above 100 Gbit/cm 2 with a reasonably small variation in switching voltage. This work provides pitch scaling prospects toward high-density STT-MRAM with ultra-small MTJs.
- 21 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (2) , 184-187
Pitch Scaling Prospect of Ultra-Small Magnetic Tunnel Junctions for High-Density STT-MRAM: Effects of Magnetostatic Interference From Neighboring Bits
Magnetic tunnel junction (MTJ) miniaturization has been demonstrated down to 2 nm with performance applicable to a wide variety of applications. In highly dense STT-MRAM, where such ultra-small MTJs are packed with tight pitches, magnetostatic interference from neighboring bits becomes a concern. In this study, we investigate the impact of magnetostatic interference on the ultra-small MTJs with various stack structures when integrated in highly dense arrays and discuss the scaling prospect. We first calculate the stray fields exerted on an MTJ from neighboring bits and then evaluate the tolerance of the MTJ against the field by measuring the external field dependence of the switching voltage of isolated MTJs. We find that STT-MRAM using the ultra-small MTJs has the potential to achieve a large capacity above 100 Gbit/cm 2 with a reasonably small variation in switching voltage. This work provides pitch scaling prospects toward high-density STT-MRAM with ultra-small MTJs.
- 30 March 2023
- Published by American Physical Society (APS) in Physical Review B
- Vol. 107 (9) , 094436
Nonlinear conductance in nanoscale CoFeB/MgO magnetic tunnel junctions with perpendicular easy axis
Magnetic tunnel junctions (MTJ) exhibit spin-dependent conductance that governs their performance in various applications. While the transport characteristics are known to show nonlinearity, their behavior and underlying mechanism have not yet understood well. Here we investigate nonlinear conductance at a low bias regime in nanoscale MTJs with a perpendicular magnetic easy axis and various junction sizes, by measuring current-voltage () characteristics and ferromagnetic resonance. We evaluate properties as under various external magnetic fields and examine the correlations among , and . We find that increases with decrease in the junction size, has a negative correlation with , and has a positive correlation with . These results can be explained by considering the spin flip during the tunneling and a modulation of material properties at the device edge caused by the nanofabrication process. Ferromagnetic resonance measurements support the physical picture suggested by the transport measurements. Our findings shed light on the mechanism of electron transport in nanoscale MTJs and facilitate the establishment of a rigorous model describing their nonlinear conductance.- 30 March 2023
- Published by American Physical Society (APS) in Physical Review B
- Vol. 107 (9) , 094436
Nonlinear conductance in nanoscale CoFeB/MgO magnetic tunnel junctions with perpendicular easy axis
Magnetic tunnel junctions (MTJ) exhibit spin-dependent conductance that governs their performance in various applications. While the transport characteristics are known to show nonlinearity, their behavior and underlying mechanism have not yet understood well. Here we investigate nonlinear conductance at a low bias regime in nanoscale MTJs with a perpendicular magnetic easy axis and various junction sizes, by measuring current-voltage () characteristics and ferromagnetic resonance. We evaluate properties as under various external magnetic fields and examine the correlations among , and . We find that increases with decrease in the junction size, has a negative correlation with , and has a positive correlation with . These results can be explained by considering the spin flip during the tunneling and a modulation of material properties at the device edge caused by the nanofabrication process. Ferromagnetic resonance measurements support the physical picture suggested by the transport measurements. Our findings shed light on the mechanism of electron transport in nanoscale MTJs and facilitate the establishment of a rigorous model describing their nonlinear conductance.- 31 January 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (5) , 052404
Nanometer-thin L1-MnAl film with B2-CoAl underlayer for high-speed and high-density STT-MRAM: Structure and magnetic properties
The material development of magnetic tunnel junction with a perpendicular easy axis is in great demand to advance spin-transfer torque magnetoresistive random access memory (STT-MRAM) technologies. To realize high-speed and high-density STT-MRAM, a thin-film magnetic material with large perpendicular anisotropy and small spontaneous magnetization has great potential. Here, we develop a thin-film deposition technique for a-few-nanometer-thin L10-MnAl by sputtering and investigate its structure and magnetic properties. Utilization of the B2-CoAl buffer layer allows us to grow L10-MnAl with a large crystalline anisotropy of 8.5 × 105 J/m3, the small spontaneous magnetization of 0.62 T, and the tolerance for 400 °C annealing even at the MnAl thickness of 2 nm. We calculate the device properties based on the obtained material parameters and find that high retention properties, high-speed switching, and low write-error rate can be obtained at the single-digit-nm region, which are not readily achieved by conventional material systems. The results show the potential of L10-MnAl for high-density and high-speed STT-MRAM.
- 31 January 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (5) , 052404
Nanometer-thin L1-MnAl film with B2-CoAl underlayer for high-speed and high-density STT-MRAM: Structure and magnetic properties
The material development of magnetic tunnel junction with a perpendicular easy axis is in great demand to advance spin-transfer torque magnetoresistive random access memory (STT-MRAM) technologies. To realize high-speed and high-density STT-MRAM, a thin-film magnetic material with large perpendicular anisotropy and small spontaneous magnetization has great potential. Here, we develop a thin-film deposition technique for a-few-nanometer-thin L10-MnAl by sputtering and investigate its structure and magnetic properties. Utilization of the B2-CoAl buffer layer allows us to grow L10-MnAl with a large crystalline anisotropy of 8.5 × 105 J/m3, the small spontaneous magnetization of 0.62 T, and the tolerance for 400 °C annealing even at the MnAl thickness of 2 nm. We calculate the device properties based on the obtained material parameters and find that high retention properties, high-speed switching, and low write-error rate can be obtained at the single-digit-nm region, which are not readily achieved by conventional material systems. The results show the potential of L10-MnAl for high-density and high-speed STT-MRAM.
- 13 December 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (24) , 242403
Temperature dependence of intrinsic critical current in perpendicular easy axis CoFeB/MgO magnetic tunnel junctions
Current induced magnetization switching in CoFeB/MgO-based magnetic tunnel junctions (MTJs) with a perpendicular easy axis is studied above room temperature. The intrinsic critical current IC0 of the MTJs decreases with increasing temperature. From a vector-network-analyzer ferromagnetic resonance measurement with a heating system, temperature dependence of magnetic anisotropy and damping constant is evaluated. We find that the reduction of IC0 at elevated temperature is mainly due to a decrease in magnetic anisotropy. A slight increase in the damping constant with temperature rise is also observed, consistent with the mechanism considering electron scattering through the inter-band transition.
- 13 December 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (24) , 242403
Temperature dependence of intrinsic critical current in perpendicular easy axis CoFeB/MgO magnetic tunnel junctions
Current induced magnetization switching in CoFeB/MgO-based magnetic tunnel junctions (MTJs) with a perpendicular easy axis is studied above room temperature. The intrinsic critical current IC0 of the MTJs decreases with increasing temperature. From a vector-network-analyzer ferromagnetic resonance measurement with a heating system, temperature dependence of magnetic anisotropy and damping constant is evaluated. We find that the reduction of IC0 at elevated temperature is mainly due to a decrease in magnetic anisotropy. A slight increase in the damping constant with temperature rise is also observed, consistent with the mechanism considering electron scattering through the inter-band transition.
- Top Cited Papers
- 13 May 2021
- Published by Springer Nature in Nature Materials
- Vol. 20 (10) , 1364-1370
Chiral-spin rotation of non-collinear antiferromagnet by spin–orbit torque
Electrical manipulation of magnetic materials by current-induced spin torque constitutes the basis of spintronics. Here, we show an unconventional response to spin–orbit torque of a non-collinear antiferromagnet Mn3Sn, which has attracted attention owing to its large anomalous Hall effect despite a vanishingly small net magnetization. In epitaxial heavy-metal/Mn3Sn heterostructures, we observe a characteristic fluctuation of the Hall resistance under the application of electric current. This observation is explained by a rotation of the chiral-spin structure of Mn3Sn driven by spin–orbit torque. We find that the variation of the magnitude of anomalous Hall effect fluctuation with sample size correlates with the number of magnetic domains in the Mn3Sn layer. In addition, the dependence of the critical current on Mn3Sn layer thickness reveals that spin–orbit torque generated by small current densities, below 20 MA cm−2, effectively acts on the chiral-spin structure even in Mn3Sn layers that are thicker than 20 nm. The results provide additional pathways for electrical manipulation of magnetic materials.
- 13 May 2021
- Published by Springer Nature in Nature Materials
- Vol. 20 (10) , 1364-1370
Top Cited PapersChiral-spin rotation of non-collinear antiferromagnet by spin–orbit torque
Electrical manipulation of magnetic materials by current-induced spin torque constitutes the basis of spintronics. Here, we show an unconventional response to spin–orbit torque of a non-collinear antiferromagnet Mn3Sn, which has attracted attention owing to its large anomalous Hall effect despite a vanishingly small net magnetization. In epitaxial heavy-metal/Mn3Sn heterostructures, we observe a characteristic fluctuation of the Hall resistance under the application of electric current. This observation is explained by a rotation of the chiral-spin structure of Mn3Sn driven by spin–orbit torque. We find that the variation of the magnitude of anomalous Hall effect fluctuation with sample size correlates with the number of magnetic domains in the Mn3Sn layer. In addition, the dependence of the critical current on Mn3Sn layer thickness reveals that spin–orbit torque generated by small current densities, below 20 MA cm−2, effectively acts on the chiral-spin structure even in Mn3Sn layers that are thicker than 20 nm. The results provide additional pathways for electrical manipulation of magnetic materials.