Sara Bisone
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sara Bisone has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Guy Mercier
Institut National de la Recherche Scientifique (Centre Eau, Terre et Environnement), Université du Québec, Québec, Canada
3 shared publications- Mathieu Gautier
Univ Lyon, INSA Lyon, DEEP (Déchets Eaux Environnement Pollutions), EA 7429, 69621 Villeurbanne Cedex, France
3 shared publications - Jean-François Blais
Centre Eau Terre Environnement (ETE), Institut National de la Recherche Scientifique (INRS), 490 Rue de la Couronne, Quebec City, QC G1K 9A9, Canada
2 shared publications - Vincent Chatain
Déchets Eaux Environnement Pollutions
2 shared publications Denise Blanc
LGCIE—DEEP (Déchets Eau Environnement Pollutions), EA4126, Université de Lyon, INSA Lyon, Villeurbanne Cedex, France
1 shared publication- Denise Blanc
Laboratoire de Génie Civil et d'Ingénierie Environnementale
1 shared publication
Latest Publications
- 3 June 2016
- Published by Taylor & Francis in Environmental Technology
- Vol. 38 (2) , 163-174
Influence of loading rate and modes on infiltration of treated wastewater in soil-based constructed wetland
Over the last 10 years soil-based constructed wetlands for discharge of treated wastewater (TWW) are commonly presented as a valuable option to provide tertiary treatment. The uncomplete knowledge in soil modifications and a lack of clear design practices laid the foundation of this work. The aim of this study was to determine optimal hydraulic loads and to observe the main critical parameters affecting treating performances and hydraulic loads acceptance. For this purpose, a soil rich in clay and backfill was chosen to perform column infiltration tests with TWW. Two loading rates and two loading modes were compared to study the influence of an intermittent feeding. Inlet and outlet waters were periodically analysed and columns were instrumented with balances, tensiometers, O2 and temperature probes. Soil physico-chemical characteristics were also taken into account to better understand the modification of the soil. One of the main expectations of tertiary treatment is to improve phosphate removal. A particular attention was thus given to phosphorus retention. The interest of an intermittent feeding in presence of a soil with high clay content was showed. This study highlighted that an intermittent feeding could make possible the use of a clay-rich soil for water infiltration.
- 3 June 2016
- Published by Taylor & Francis in Environmental Technology
- Vol. 38 (2) , 163-174
Influence of loading rate and modes on infiltration of treated wastewater in soil-based constructed wetland
Over the last 10 years soil-based constructed wetlands for discharge of treated wastewater (TWW) are commonly presented as a valuable option to provide tertiary treatment. The uncomplete knowledge in soil modifications and a lack of clear design practices laid the foundation of this work. The aim of this study was to determine optimal hydraulic loads and to observe the main critical parameters affecting treating performances and hydraulic loads acceptance. For this purpose, a soil rich in clay and backfill was chosen to perform column infiltration tests with TWW. Two loading rates and two loading modes were compared to study the influence of an intermittent feeding. Inlet and outlet waters were periodically analysed and columns were instrumented with balances, tensiometers, O2 and temperature probes. Soil physico-chemical characteristics were also taken into account to better understand the modification of the soil. One of the main expectations of tertiary treatment is to improve phosphate removal. A particular attention was thus given to phosphorus retention. The interest of an intermittent feeding in presence of a soil with high clay content was showed. This study highlighted that an intermittent feeding could make possible the use of a clay-rich soil for water infiltration.
- 11 February 2016
- Published by Springer Nature in Environmental Earth Sciences
- Vol. 75 (4) , 1-9
Geochemical characterization and modeling of arsenic behavior in a highly contaminated mining soil
- 11 February 2016
- Published by Springer Nature in Environmental Earth Sciences
- Vol. 75 (4) , 1-9
Geochemical characterization and modeling of arsenic behavior in a highly contaminated mining soil
- 22 March 2013
- Published by Taylor & Francis in Environmental Technology
- Vol. 34 (18) , 2633-2648
Decontamination of metals and polycyclic aromatic hydrocarbons from slag-polluted soil
Metallurgy is an industrial activity that is one of the largest contributors to soil contamination by metals. This contamination is often associated with organic compound contamination; however, little research has been aimed at the development of simultaneous processes for decontamination as opposed to treatments to heavy metals or organic compounds alone. This paper presents an efficient process to decontaminate the soils polluted with smelting by-products rich in Cu, Zn and polycyclic aromatic hydrocarbons (PAHs). A simultaneous treatment for metals and PAHs was also tested. The process is mainly based on physical techniques, such as crushing, gravimetric separation and attrition. For the finest particle size fractions, an acid extraction with H2SO4 was used to remove metals. The PAH removal was enhanced by adding surfactant during attrition. The total metal removals varied from 49% to 73% for Cu and from 43% to 63% for Zn, whereas a removal yield of 92% was measured for total PAHs. Finally, a technical-economic evaluation was done for the two processes tested.
- 22 March 2013
- Published by Taylor & Francis in Environmental Technology
- Vol. 34 (18) , 2633-2648
Decontamination of metals and polycyclic aromatic hydrocarbons from slag-polluted soil
Metallurgy is an industrial activity that is one of the largest contributors to soil contamination by metals. This contamination is often associated with organic compound contamination; however, little research has been aimed at the development of simultaneous processes for decontamination as opposed to treatments to heavy metals or organic compounds alone. This paper presents an efficient process to decontaminate the soils polluted with smelting by-products rich in Cu, Zn and polycyclic aromatic hydrocarbons (PAHs). A simultaneous treatment for metals and PAHs was also tested. The process is mainly based on physical techniques, such as crushing, gravimetric separation and attrition. For the finest particle size fractions, an acid extraction with H2SO4 was used to remove metals. The PAH removal was enhanced by adding surfactant during attrition. The total metal removals varied from 49% to 73% for Cu and from 43% to 63% for Zn, whereas a removal yield of 92% was measured for total PAHs. Finally, a technical-economic evaluation was done for the two processes tested.
- 8 March 2013
- Published by Taylor & Francis in Soil and Sediment Contamination: An International Journal
- Vol. 22 (8) , 856-875
Counter-Current Metal Leaching and Precipitation for Soil Remediation
Chemical acid leaching is an effective technique for extracting toxic metals from the finest fractions of polluted soils. Nevertheless, the use of large quantities of reagents and process water results in prohibitive operating costs. The purpose of this study was to evaluate the technical and economic advantages of recirculating water in a counter-current leaching process (CCLP). Five 1-h sulfuric acid extraction steps (at pH = 1.5) followed by three 5-min water-washing steps were applied to the fine particle fraction (−1), Cu (3 100 mg·kg−1), Mn (685 mg kg−1), Pb (550 mg·kg−1), and Zn (2 840 mg·kg−1). The leaching experiments were carried out at ambient temperature using a 10% soil suspension and in 1-L working volume stirred tank reactors. This paper presents results of conventional and counter-current leaching process (CCLP) tests and shows that the CCLP yields removal results for Cu (85%), Zn (86%), Mn (75%), and Cd (90%) that are similar to those obtained using the conventional leaching process. Moreover, the CCLP uses half of the quantity of acid and one-eighth of the amount of water that the conventional process uses. Metal precipitation with NaOH and Ca(OH)2 was applied to treat the acidic leachates, and good metal removal yields were achieved with both reagents. However, the large consumption of chemicals implies high operating costs. In addition, the precipitation causes considerable sludge production, particularly when using Ca(OH)2. Overall, the CCLP coupled to metal precipitation using NaOH and water recycling appears to be the most attractive option for the removal of toxic metals from this industrial soil.
- 8 March 2013
- Published by Taylor & Francis in Soil and Sediment Contamination: An International Journal
- Vol. 22 (8) , 856-875
Counter-Current Metal Leaching and Precipitation for Soil Remediation
Chemical acid leaching is an effective technique for extracting toxic metals from the finest fractions of polluted soils. Nevertheless, the use of large quantities of reagents and process water results in prohibitive operating costs. The purpose of this study was to evaluate the technical and economic advantages of recirculating water in a counter-current leaching process (CCLP). Five 1-h sulfuric acid extraction steps (at pH = 1.5) followed by three 5-min water-washing steps were applied to the fine particle fraction (−1), Cu (3 100 mg·kg−1), Mn (685 mg kg−1), Pb (550 mg·kg−1), and Zn (2 840 mg·kg−1). The leaching experiments were carried out at ambient temperature using a 10% soil suspension and in 1-L working volume stirred tank reactors. This paper presents results of conventional and counter-current leaching process (CCLP) tests and shows that the CCLP yields removal results for Cu (85%), Zn (86%), Mn (75%), and Cd (90%) that are similar to those obtained using the conventional leaching process. Moreover, the CCLP uses half of the quantity of acid and one-eighth of the amount of water that the conventional process uses. Metal precipitation with NaOH and Ca(OH)2 was applied to treat the acidic leachates, and good metal removal yields were achieved with both reagents. However, the large consumption of chemicals implies high operating costs. In addition, the precipitation causes considerable sludge production, particularly when using Ca(OH)2. Overall, the CCLP coupled to metal precipitation using NaOH and water recycling appears to be the most attractive option for the removal of toxic metals from this industrial soil.
- 29 March 2012
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 223 (7) , 3739-3755
Toxic Metal Removal from Polluted Soil by Acid Extraction
- 29 March 2012
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 223 (7) , 3739-3755
Toxic Metal Removal from Polluted Soil by Acid Extraction