Richard J. T. Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Richard J. T. Lin has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Debes Bhattacharyya
Centre for Advanced Composite Materials (CACM), Department of Mechanical Engineering, University of Auckland, Private Bag 92019, Auckland 1142, New Zealand
22 shared publications - Azwan Iskandar Azmi
Faculty of Mechanical Engineering and Technology, Universiti Malaysia Perlis, Arau, Malaysia
6 shared publications - Krishnan Jayaraman
Centre for Advanced Composite Materials (CACM), Department of Mechanical Engineering, University of Auckland, Private Bag 92019, Auckland 1142, New Zealand
5 shared publications S. Fakirov
5 shared publications- Nam Kyeun Kim
University of Auckland
3 shared publications W. Yan
3 shared publications
Latest Publications
- Open Access
- 22 February 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 4716-4733
Investigation on microstructure characteristics of tool wear and machined surface mechanisms while milling: kenaf vs glass fiber-reinforced composites
- 22 February 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 4716-4733
Open AccessInvestigation on microstructure characteristics of tool wear and machined surface mechanisms while milling: kenaf vs glass fiber-reinforced composites
- Open Access
Development of 3D Slurry Printing Technology with Submersion-Light Apparatus in Dental Application
This study proposes an innovative three-dimensional printing technology with submersion-light apparatus. A zirconia powder with an average particle size of 0.5 µm is mixed with 1,6-Hexanediol diacrylate (HDDA) and photo-initiator to form a slurry. The weight percentage of zirconia powder to HDDA is 70:30 wt.%. A light engine box is submerged in a slurry and emits a layered pattern to induce photopolymerization and transform a slurry into a printed green body. Green body sintering parameters for the first and second stages are 380 °C with a holding time of 1.5 h and 1550 °C with a holding time of 2 h. The sintered parts’ length, width, and height shrinkage ratios are 29.9%, 29.7%, and 30.6%. The ball milling decreases the powder particle size to 158 ± 16 nm and the mean grain size of the sintered part is 423 ± 25 nm. The sintered part has an average hardness of 1224 (HV), a density of 5.45 g/cm3, and a flexural strength of 641.04 MPa. A three-unit zirconia dental bridge also has been fabricated with a clinically acceptable marginal gap.
Open AccessDevelopment of 3D Slurry Printing Technology with Submersion-Light Apparatus in Dental Application
This study proposes an innovative three-dimensional printing technology with submersion-light apparatus. A zirconia powder with an average particle size of 0.5 µm is mixed with 1,6-Hexanediol diacrylate (HDDA) and photo-initiator to form a slurry. The weight percentage of zirconia powder to HDDA is 70:30 wt.%. A light engine box is submerged in a slurry and emits a layered pattern to induce photopolymerization and transform a slurry into a printed green body. Green body sintering parameters for the first and second stages are 380 °C with a holding time of 1.5 h and 1550 °C with a holding time of 2 h. The sintered parts’ length, width, and height shrinkage ratios are 29.9%, 29.7%, and 30.6%. The ball milling decreases the powder particle size to 158 ± 16 nm and the mean grain size of the sintered part is 423 ± 25 nm. The sintered part has an average hardness of 1224 (HV), a density of 5.45 g/cm3, and a flexural strength of 641.04 MPa. A three-unit zirconia dental bridge also has been fabricated with a clinically acceptable marginal gap.
- Open Access
- 1 November 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 15, 4610-4622
Effects of graphene network formation on microstructure and mechanical properties of flax/epoxy nanocomposites
- 1 November 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 15, 4610-4622
Open AccessEffects of graphene network formation on microstructure and mechanical properties of flax/epoxy nanocomposites
- 12 August 2019
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 25 (7) , 1187-1197
A comparison of the marginal fit and mechanical properties of a zirconia dental crown using CAM and 3DSP
Purpose: This study aims to compare the marginal fit, flexural strength and hardness for a ceramic premolar that is constructed using dental computer aided machining (CAM) and three-dimensional slurry printing (3DSP).Design/methodology/approach: Dental CAM and 3DSP are used to fabricate a premolar model. To reduce the fabrication time for 3DSP, a new composition of solvent-free slurry is proposed. Before it is fabricated, the dimensions of the green body for the premolar model are enlarged to account for the shrinkage ratio. A two-stage sintering process ensures accurate final dimensions for the premolar model. The surface morphology of the green body and the sintered premolars that are produced using the two methods is then determined using scanning electronic microscopy. The sintered premolars are seated on a stone model to determine the marginal gap using an optical microscope. The hardness and the flexural strength are also measured for the purpose of comparison.Findings: The developed solvent-free slurry for 3DSP can be used to produce a premolar green body without micro-cracks or delamination. The maximal marginal gap for the sintered premolar parts that are constructed using the green bodies from dental CAM is 98.9 µm and that from 3DSP is 72 µm. Both methods produce a highly dense zirconia premolar using the same sintering conditions. The hardness value for the dental CAM group is 1238.8 HV, which is slightly higher than that for the 3DSP group (1189.4 HV) because there is a difference in the pre-processing of the initial ceramic materials. However, the flexural strength for 3DSP is 716.76 MPa, which is less than the requirement for clinical use.Originality/value: This study verifies that 3DSP can be used to fabricate a zirconia dental restoration device that is as good as the one that is produced using the dental CAM system and which has a marginal gap that is smaller than the threshold value. The resulting premolar restoration devices that are produced by sintering the green bodies that are produced using 3DSP and dental CAM under the same conditions have a similar hardness value, which is four times greater than that of enamel. The flexural strength of 3DSP does not meet the requirement for clinical use.
- 12 August 2019
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 25 (7) , 1187-1197
A comparison of the marginal fit and mechanical properties of a zirconia dental crown using CAM and 3DSP
Purpose: This study aims to compare the marginal fit, flexural strength and hardness for a ceramic premolar that is constructed using dental computer aided machining (CAM) and three-dimensional slurry printing (3DSP).Design/methodology/approach: Dental CAM and 3DSP are used to fabricate a premolar model. To reduce the fabrication time for 3DSP, a new composition of solvent-free slurry is proposed. Before it is fabricated, the dimensions of the green body for the premolar model are enlarged to account for the shrinkage ratio. A two-stage sintering process ensures accurate final dimensions for the premolar model. The surface morphology of the green body and the sintered premolars that are produced using the two methods is then determined using scanning electronic microscopy. The sintered premolars are seated on a stone model to determine the marginal gap using an optical microscope. The hardness and the flexural strength are also measured for the purpose of comparison.Findings: The developed solvent-free slurry for 3DSP can be used to produce a premolar green body without micro-cracks or delamination. The maximal marginal gap for the sintered premolar parts that are constructed using the green bodies from dental CAM is 98.9 µm and that from 3DSP is 72 µm. Both methods produce a highly dense zirconia premolar using the same sintering conditions. The hardness value for the dental CAM group is 1238.8 HV, which is slightly higher than that for the 3DSP group (1189.4 HV) because there is a difference in the pre-processing of the initial ceramic materials. However, the flexural strength for 3DSP is 716.76 MPa, which is less than the requirement for clinical use.Originality/value: This study verifies that 3DSP can be used to fabricate a zirconia dental restoration device that is as good as the one that is produced using the dental CAM system and which has a marginal gap that is smaller than the threshold value. The resulting premolar restoration devices that are produced by sintering the green bodies that are produced using 3DSP and dental CAM under the same conditions have a similar hardness value, which is four times greater than that of enamel. The flexural strength of 3DSP does not meet the requirement for clinical use.
- 1 December 2014
- Published by Elsevier in Composites Part B: Engineering
- Vol. 67, 472-480
Extruded short wool fibre composites: Mechanical and fire retardant properties
- 1 December 2014
- Published by Elsevier in Composites Part B: Engineering
- Vol. 67, 472-480
Extruded short wool fibre composites: Mechanical and fire retardant properties
- 23 September 2014
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 33 (22) , 2021-2033
Optimisation of material compositions for flammability characteristics in rice husk/polyethylene composites
A parametric study on the flammability characteristics of rice husk-reinforced polyethylene composites with various material compositions was conducted to find the “best” composites’ formulation for fire retardancy. Composites were manufactured using rice husk, maleated anhydride polyethylene and linear medium density polyethylene. The blends for manufacturing of composites were selected using mixture design approach. The individual effects of each constituent material on the fire performance of composites by cone calorimeter were studied using trace and contour plots for the various thermal and flammability properties. Regression coefficients were also estimated for each measured response. The cone calorimetry results show that the addition of rice husk improved fire retardancy of composites. The addition of maleated anhydride polyethylene did not influence the flammability properties much, except for mass loss rate and specific extinction area. The optimum mixture of rice husk, maleated anhydride polyethylene and linear medium density polyethylene for overall “best” flammability properties of the composites was also determined by multiple response optimisation using the regression models in Design Expert software. The optimum mixture for overall “best” fire retardant properties was found to be 50 wt% of rice husk, 5.6 wt% of maleated anhydride polyethylene and 44.4 wt% of linear medium density polyethylene. The flammability properties measured from composites manufactured with this formulation closely matched the values predicted by the model.
- 23 September 2014
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 33 (22) , 2021-2033
Optimisation of material compositions for flammability characteristics in rice husk/polyethylene composites
A parametric study on the flammability characteristics of rice husk-reinforced polyethylene composites with various material compositions was conducted to find the “best” composites’ formulation for fire retardancy. Composites were manufactured using rice husk, maleated anhydride polyethylene and linear medium density polyethylene. The blends for manufacturing of composites were selected using mixture design approach. The individual effects of each constituent material on the fire performance of composites by cone calorimeter were studied using trace and contour plots for the various thermal and flammability properties. Regression coefficients were also estimated for each measured response. The cone calorimetry results show that the addition of rice husk improved fire retardancy of composites. The addition of maleated anhydride polyethylene did not influence the flammability properties much, except for mass loss rate and specific extinction area. The optimum mixture of rice husk, maleated anhydride polyethylene and linear medium density polyethylene for overall “best” flammability properties of the composites was also determined by multiple response optimisation using the regression models in Design Expert software. The optimum mixture for overall “best” fire retardant properties was found to be 50 wt% of rice husk, 5.6 wt% of maleated anhydride polyethylene and 44.4 wt% of linear medium density polyethylene. The flammability properties measured from composites manufactured with this formulation closely matched the values predicted by the model.
- 1 June 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 575, 223-226
Effects of Fibre Loading and Interfacial Modification on Physical Properties of Rice Husk/PE Composites
In this study, the physical properties of thermoplastic composites manufactured from linear medium density polyethylene (LMDPE), rice husk (RH) and maleic anhydride polyethylene (MAPE) were evaluated. Composites were manufactured with RH loadings of 15 wt%, 30 wt% and 50 wt% with 1 wt% of MAPE to investigate the effect of RH loading on the physical properties (water absorption and thickness swelling) of the composites. The results show that the water absorption and the corresponding thickness swelling increased with an increase in RH loading. Further manufacturing was carried out with 50 wt% of RH and 1wt%, 3.5 wt% and 6 wt% of MAPE to evaluate the effects of interfacial modification on the physical properties of the composites. The results show that the composites with 3.5 wt% of MAPE had least water absorption and the corresponding thickness swelling, whereas the composites having 1 wt% of MAPE had maximum water absorption and the thickness swelling. It can be concluded from these experiments that fibre loading as well as interfacial modification play a significant role in determining the physical properties of the composites.
- 1 June 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 575, 223-226
Effects of Fibre Loading and Interfacial Modification on Physical Properties of Rice Husk/PE Composites
In this study, the physical properties of thermoplastic composites manufactured from linear medium density polyethylene (LMDPE), rice husk (RH) and maleic anhydride polyethylene (MAPE) were evaluated. Composites were manufactured with RH loadings of 15 wt%, 30 wt% and 50 wt% with 1 wt% of MAPE to investigate the effect of RH loading on the physical properties (water absorption and thickness swelling) of the composites. The results show that the water absorption and the corresponding thickness swelling increased with an increase in RH loading. Further manufacturing was carried out with 50 wt% of RH and 1wt%, 3.5 wt% and 6 wt% of MAPE to evaluate the effects of interfacial modification on the physical properties of the composites. The results show that the composites with 3.5 wt% of MAPE had least water absorption and the corresponding thickness swelling, whereas the composites having 1 wt% of MAPE had maximum water absorption and the thickness swelling. It can be concluded from these experiments that fibre loading as well as interfacial modification play a significant role in determining the physical properties of the composites.
- 14 March 2014
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 131 (16)
Optimal formulation of rice husk reinforced polyethylene composites for mechanical performance: A mixture design approach
Rice husk (RH) and linear medium density polyethylene (LMDPE) were used along with maleic anhydride grafted polyethylene (MAPE) to study the effects of component composition on the mechanical properties of the composites. Ten different blends along with four replicated blends were prepared with different selected percentages of RH, MAPE and LMDPE using mixture design approach. Trace and contour plots were used to examine the effects of RH, MAPE and LMDPE on the mechanical properties of the manufactured composites. Regression coefficients were also estimated for each fitted response (mechanical property). The results show that tensile and flexural properties of the composites improved with an increase in amount of RH, whereas Charpy impact strength decreased with increasing fibre loading. Tensile strength, flexural strength and Charpy impact strength increased with an increase in MAPE loading up to a certain percentage of MAPE, beyond which any further increase decreased these properties. The effect of MAPE on tensile and flexural modulus was not significant. The fitted models were used to optimise formulation of RH, MAPE and LMDPE for multiple responses for overall “best” mechanical properties. The optimal formulation for the overall “best” mechanical properties were found to be 50 wt% for RH, 4.1 wt% for MAPE and 45.9 wt% for LMDPE. The mechanical properties of the composite manufactured with this formulation closely matched the values predicted by the models. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 40647.
- 14 March 2014
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 131 (16)
Optimal formulation of rice husk reinforced polyethylene composites for mechanical performance: A mixture design approach
Rice husk (RH) and linear medium density polyethylene (LMDPE) were used along with maleic anhydride grafted polyethylene (MAPE) to study the effects of component composition on the mechanical properties of the composites. Ten different blends along with four replicated blends were prepared with different selected percentages of RH, MAPE and LMDPE using mixture design approach. Trace and contour plots were used to examine the effects of RH, MAPE and LMDPE on the mechanical properties of the manufactured composites. Regression coefficients were also estimated for each fitted response (mechanical property). The results show that tensile and flexural properties of the composites improved with an increase in amount of RH, whereas Charpy impact strength decreased with increasing fibre loading. Tensile strength, flexural strength and Charpy impact strength increased with an increase in MAPE loading up to a certain percentage of MAPE, beyond which any further increase decreased these properties. The effect of MAPE on tensile and flexural modulus was not significant. The fitted models were used to optimise formulation of RH, MAPE and LMDPE for multiple responses for overall “best” mechanical properties. The optimal formulation for the overall “best” mechanical properties were found to be 50 wt% for RH, 4.1 wt% for MAPE and 45.9 wt% for LMDPE. The mechanical properties of the composite manufactured with this formulation closely matched the values predicted by the models. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 40647.