Wenbo Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Wenbo Liu has a total of 87 co-authors. Here are the top co-authors by number of shared publications:
- Chi Zhang
Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences
8 shared publications - Tianzhao Bu
CAS Center for Excellence in Nanoscience, Beijing Key Laboratory of Micro-Nano Energy and Sensor, Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, Beijing 101400, China
5 shared publications - Fengben Xi
CAS Center for Excellence in Nanoscience Beijing Key Laboratory of Micro‐nano Energy and Sensor Beijing Institute of Nanoenergy and Nanosystems Chinese Academy of Sciences Beijing 100083 P. R. China
4 shared publications Guoxu Liu
CAS Center for Excellence in Nanoscience, Beijing Key Laboratory of Micro-nano Energy and Sensor, Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, Beijing 100083, China
4 shared publicationsHang Yang
CAS Center for Excellence in Nanoscience, Beijing Key Laboratory of Micro-nano Energy and Sensor, Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, Beijing 100083, China
3 shared publications- Tong Guo
State Key Laboratory for Artificial Microstructure and Mesoscopic Physics, School of Physics, Peking University, Beijing 100871, China
3 shared publications
Latest Publications
- Open Access
- 2 April 2026
- Published by Springer Nature in Communications Engineering
- Vol. 5 (1)
Robust bionic distributed multimodal flexible sensor for extreme-condition sensing and intelligent operation
Traditional multimodal flexible sensors struggle with system integration, limited node scalability, and overall robustness, posing multiple critical challenges. Inspired by the tiger-shark scalp, we present BDMFS, a robust bionic distributed multimodal flexible sensor, integrating an S-shaped optical network mimicking subcutaneous mechanoreceptors with a self-powered triboelectric interface emulating ampullae-based proximity sensing. A microstructured elastic dielectric layer serves as both optical substrate and triboelectric layer, providing exceptional flexibility, mechanical robustness, and environmental adaptability under diverse conditions. BDMFS enables spatiotemporally synchronized perception of proximity (~ 100 mm) and tactile (~ 5 ms) stimuli, detecting gentle touches of 0.25 g while withstanding 6.26 MPa pressures. Coupled with machine-learning, it achieves 95.26% object-proximity recognition accuracy, demonstrated in real-time virtual music teaching, adaptive grasping under low light, and wrist-mounted underwater teleoperation, highlighting its potential for intelligent control and advanced human-robot interaction in extreme environments.
- 2 April 2026
- Published by Springer Nature in Communications Engineering
- Vol. 5 (1)
Open AccessRobust bionic distributed multimodal flexible sensor for extreme-condition sensing and intelligent operation
Traditional multimodal flexible sensors struggle with system integration, limited node scalability, and overall robustness, posing multiple critical challenges. Inspired by the tiger-shark scalp, we present BDMFS, a robust bionic distributed multimodal flexible sensor, integrating an S-shaped optical network mimicking subcutaneous mechanoreceptors with a self-powered triboelectric interface emulating ampullae-based proximity sensing. A microstructured elastic dielectric layer serves as both optical substrate and triboelectric layer, providing exceptional flexibility, mechanical robustness, and environmental adaptability under diverse conditions. BDMFS enables spatiotemporally synchronized perception of proximity (~ 100 mm) and tactile (~ 5 ms) stimuli, detecting gentle touches of 0.25 g while withstanding 6.26 MPa pressures. Coupled with machine-learning, it achieves 95.26% object-proximity recognition accuracy, demonstrated in real-time virtual music teaching, adaptive grasping under low light, and wrist-mounted underwater teleoperation, highlighting its potential for intelligent control and advanced human-robot interaction in extreme environments.
- Top Cited Papers
- 18 April 2025
- Published by Springer Nature in Nature Machine Intelligence
- Vol. 7 (5) , 703-715
Transforming machines capable of continuous 3D shape morphing and locking
- 18 April 2025
- Published by Springer Nature in Nature Machine Intelligence
- Vol. 7 (5) , 703-715
Top Cited PapersTransforming machines capable of continuous 3D shape morphing and locking
- 24 August 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (41)
An Intelligent Robotic System Capable of Sensing and Describing Objects Based on Bimodal, Self‐Powered Flexible Sensors
This study presents an intelligent soft robotic system capable of perceiving, describing, and sorting objects based on their physical properties. This work introduces a bimodal self‐powered flexible sensor (BSFS) based on the triboelectric nanogenerator and giant magnetoelastic effect. The BSFS features a simplified structure comprising a magnetoelastic conductive film and a packaged liquid metal coil. The BSFS can precisely detect and distinguish touchless and tactile models, with a response time of 10 ms. By seamlessly integrating the BSFSs into the soft fingers, this study realizes an anthropomorphic soft robotic hand with remarkable multimodal perception capabilities. The touchless signals provide valuable insights into object shape and material composition, while the tactile signals offer precise information regarding surface roughness. Utilizing a convolutional neural network (CNN), this study integrates all sensing information, resulting in an intelligent soft robotic system that accurately describes objects based on their physical properties, including materials, surface roughness, and shapes, with an accuracy rate of up to 97%. This study may lay a robotic foundation for the hardware of the general artificial intelligence with capacities to interpret and interact with the physical world, which also serves as an interface between artificial intelligence and soft robots.
- 24 August 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (41)
An Intelligent Robotic System Capable of Sensing and Describing Objects Based on Bimodal, Self‐Powered Flexible Sensors
This study presents an intelligent soft robotic system capable of perceiving, describing, and sorting objects based on their physical properties. This work introduces a bimodal self‐powered flexible sensor (BSFS) based on the triboelectric nanogenerator and giant magnetoelastic effect. The BSFS features a simplified structure comprising a magnetoelastic conductive film and a packaged liquid metal coil. The BSFS can precisely detect and distinguish touchless and tactile models, with a response time of 10 ms. By seamlessly integrating the BSFSs into the soft fingers, this study realizes an anthropomorphic soft robotic hand with remarkable multimodal perception capabilities. The touchless signals provide valuable insights into object shape and material composition, while the tactile signals offer precise information regarding surface roughness. Utilizing a convolutional neural network (CNN), this study integrates all sensing information, resulting in an intelligent soft robotic system that accurately describes objects based on their physical properties, including materials, surface roughness, and shapes, with an accuracy rate of up to 97%. This study may lay a robotic foundation for the hardware of the general artificial intelligence with capacities to interpret and interact with the physical world, which also serves as an interface between artificial intelligence and soft robots.
- Top Cited PapersOpen Access
- 26 August 2022
- Published by Springer Nature in Nature Communications
- Vol. 13 (1) , 1-14
Touchless interactive teaching of soft robots through flexible bimodal sensory interfaces
In this paper, we propose a multimodal flexible sensory interface for interactively teaching soft robots to perform skilled locomotion using bare human hands. First, we develop a flexible bimodal smart skin (FBSS) based on triboelectric nanogenerator and liquid metal sensing that can perform simultaneous tactile and touchless sensing and distinguish these two modes in real time. With the FBSS, soft robots can react on their own to tactile and touchless stimuli. We then propose a distance control method that enabled humans to teach soft robots movements via bare hand-eye coordination. The results showed that participants can effectively teach a self-reacting soft continuum manipulator complex motions in three-dimensional space through a “shifting sensors and teaching” method within just a few minutes. The soft manipulator can repeat the human-taught motions and replay them at different speeds. Finally, we demonstrate that humans can easily teach the soft manipulator to complete specific tasks such as completing a pen-and-paper maze, taking a throat swab, and crossing a barrier to grasp an object. We envision that this user-friendly, non-programmable teaching method based on flexible multimodal sensory interfaces could broadly expand the domains in which humans interact with and utilize soft robots.
- 26 August 2022
- Published by Springer Nature in Nature Communications
- Vol. 13 (1) , 1-14
Top Cited PapersOpen AccessTouchless interactive teaching of soft robots through flexible bimodal sensory interfaces
In this paper, we propose a multimodal flexible sensory interface for interactively teaching soft robots to perform skilled locomotion using bare human hands. First, we develop a flexible bimodal smart skin (FBSS) based on triboelectric nanogenerator and liquid metal sensing that can perform simultaneous tactile and touchless sensing and distinguish these two modes in real time. With the FBSS, soft robots can react on their own to tactile and touchless stimuli. We then propose a distance control method that enabled humans to teach soft robots movements via bare hand-eye coordination. The results showed that participants can effectively teach a self-reacting soft continuum manipulator complex motions in three-dimensional space through a “shifting sensors and teaching” method within just a few minutes. The soft manipulator can repeat the human-taught motions and replay them at different speeds. Finally, we demonstrate that humans can easily teach the soft manipulator to complete specific tasks such as completing a pen-and-paper maze, taking a throat swab, and crossing a barrier to grasp an object. We envision that this user-friendly, non-programmable teaching method based on flexible multimodal sensory interfaces could broadly expand the domains in which humans interact with and utilize soft robots.
- Open Access
Network Topology Optimization of Triboelectric Nanogenerators for Effectively Harvesting Ocean Wave Energy
- 1 December 2020
- Published by Elsevier in Biochemical and Biophysical Research Communications
- Vol. 533 (3) , 586-591
The methylation status in GNAS clusters May Be an epigenetic marker for oocyte quality
- 1 December 2020
- Published by Elsevier in Biochemical and Biophysical Research Communications
- Vol. 533 (3) , 586-591
The methylation status in GNAS clusters May Be an epigenetic marker for oocyte quality
- 1 October 2019
- Published by SAGE Publications in Soft Robotics
- Vol. 6 (5) , 664-670
Triboelectric Effect-Driven Liquid Metal Actuators
Owing to the perfect combination of metallic conductivity, liquid fluidity, and mechanical stability, liquid metals (LMs) are considered the potential materials of the electromechanical system and the basic components of liquid robot. Here, triboelectric effect-driven liquid metal actuators (TLMAs) have been demonstrated, in which the motions of LMs could be driven and accurately controlled by triboelectric nanogenerators (TENGs). By the coulomb forces of transferred triboelectric charges in interdigital electrodes and inertia effects, the LM could be driven for continuous linear and circular motions, respectively. As an alternative structure, the motion of LMs could also be accurately controlled, in which the reciprocating and merging of LMs have been demonstrated. Moreover, the TLMA could serve as a control switch to modulate on/off of an LED by integrating into a circuit, and a transport system based on TLMA has also been demonstrated. In this work, the TENG is used as a medium to first drive and accurately control LMs by external mechanical force, which may have great applications in Micro-Electro-Mechanical System (MEMS), liquid robot, and intelligent microcontroller.
- 1 October 2019
- Published by SAGE Publications in Soft Robotics
- Vol. 6 (5) , 664-670
Triboelectric Effect-Driven Liquid Metal Actuators
Owing to the perfect combination of metallic conductivity, liquid fluidity, and mechanical stability, liquid metals (LMs) are considered the potential materials of the electromechanical system and the basic components of liquid robot. Here, triboelectric effect-driven liquid metal actuators (TLMAs) have been demonstrated, in which the motions of LMs could be driven and accurately controlled by triboelectric nanogenerators (TENGs). By the coulomb forces of transferred triboelectric charges in interdigital electrodes and inertia effects, the LM could be driven for continuous linear and circular motions, respectively. As an alternative structure, the motion of LMs could also be accurately controlled, in which the reciprocating and merging of LMs have been demonstrated. Moreover, the TLMA could serve as a control switch to modulate on/off of an LED by integrating into a circuit, and a transport system based on TLMA has also been demonstrated. In this work, the TENG is used as a medium to first drive and accurately control LMs by external mechanical force, which may have great applications in Micro-Electro-Mechanical System (MEMS), liquid robot, and intelligent microcontroller.
- 1 April 2019
- Published by Elsevier in Nano Energy
- Vol. 58, 499-507
Torus structured triboelectric nanogenerator array for water wave energy harvesting
- 1 April 2019
- Published by Elsevier in Nano Energy
- Vol. 58, 499-507
Torus structured triboelectric nanogenerator array for water wave energy harvesting
- Open Access
- 5 November 2018
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 4 (1) , 25
Tribotronic bipolar junction transistor for mechanical frequency monitoring and use as touch switch
Tribotronics, a new field that involves the coupling of triboelectricity and semiconductors, has attracted great interest in the nanoenergy and nanoelectronics domains. This paper proposes a tribotronic bipolar junction transistor (TBJT) that incorporates a bipolar junction transistor and a triboelectric nanogenerator (TENG) in the single-electrode mode. When the mobile triboelectric layer slides on the device surface for electrification, a bias voltage is created and applied to the emitter junction, and then the base current from the TENG is amplified. Based on the fabricated TBJT, a mechanical frequency monitoring sensor with high sensitivity and excellent stability and a finger-triggered touch switch were developed. This work demonstrated for the first time a tribotronic device with simultaneously controlled voltage and current voltage/current simultaneously controlled tribotronic device, which has promising potential applications in micro/nano-sensors, human-machine interactions, intelligent instrumentation, wearable electronics, and other applications.
- 5 November 2018
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 4 (1) , 25
Open AccessTribotronic bipolar junction transistor for mechanical frequency monitoring and use as touch switch
Tribotronics, a new field that involves the coupling of triboelectricity and semiconductors, has attracted great interest in the nanoenergy and nanoelectronics domains. This paper proposes a tribotronic bipolar junction transistor (TBJT) that incorporates a bipolar junction transistor and a triboelectric nanogenerator (TENG) in the single-electrode mode. When the mobile triboelectric layer slides on the device surface for electrification, a bias voltage is created and applied to the emitter junction, and then the base current from the TENG is amplified. Based on the fabricated TBJT, a mechanical frequency monitoring sensor with high sensitivity and excellent stability and a finger-triggered touch switch were developed. This work demonstrated for the first time a tribotronic device with simultaneously controlled voltage and current voltage/current simultaneously controlled tribotronic device, which has promising potential applications in micro/nano-sensors, human-machine interactions, intelligent instrumentation, wearable electronics, and other applications.
- 16 August 2018
- Published by Wiley in Advanced Materials Technologies
- Vol. 3 (11)
Interdigitated Electrode‐Based Triboelectric Sliding Sensor for Security Monitoring
Security monitoring and precaution for private information and property plays a key role in the smart home system. In this work, a triboelectric nanogenerator‐based active sliding sensor is demonstrated which can monitor the position, displacement, velocity, and direction of a contact sliding objects. The device consists of a mover and a stator which operate in sliding mode. Two aligned column arrays of copper electrodes are coated on the substrate as the mover, while two interdigitated copper electrode pairs with relative position shift are coated under a polytetrafluoroethylene film as the stator. The experimental results show that a single device can generate a voltage of about 5 V at a resistance load of 60 MΩ at a sliding velocity of 0.5 m s–1. The sliding sensor can detect an ultralow velocity in 0.001 m s–1 as well as the sliding direction of the mover. The sensor can be fixed on the drawer and door to detect the motion parameters which are sent to a remote client application for security monitoring in smart home systems. The proposed sliding sensor has great potential in the Internet of things, personal motion feature recognition, and meandering trajectory tracking.
- 16 August 2018
- Published by Wiley in Advanced Materials Technologies
- Vol. 3 (11)
Interdigitated Electrode‐Based Triboelectric Sliding Sensor for Security Monitoring
Security monitoring and precaution for private information and property plays a key role in the smart home system. In this work, a triboelectric nanogenerator‐based active sliding sensor is demonstrated which can monitor the position, displacement, velocity, and direction of a contact sliding objects. The device consists of a mover and a stator which operate in sliding mode. Two aligned column arrays of copper electrodes are coated on the substrate as the mover, while two interdigitated copper electrode pairs with relative position shift are coated under a polytetrafluoroethylene film as the stator. The experimental results show that a single device can generate a voltage of about 5 V at a resistance load of 60 MΩ at a sliding velocity of 0.5 m s–1. The sliding sensor can detect an ultralow velocity in 0.001 m s–1 as well as the sliding direction of the mover. The sensor can be fixed on the drawer and door to detect the motion parameters which are sent to a remote client application for security monitoring in smart home systems. The proposed sliding sensor has great potential in the Internet of things, personal motion feature recognition, and meandering trajectory tracking.