Steve Sharples
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Steve Sharples has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
M. Clark
Advanced Optics Group, Faculty of Engineering, University of Nottingham, University Park, Nottingham, NG7 2RD, United Kingdom
22 shared publications- Richard J. Smith
Optics and Photonics Group, Faculty of Engineering, University of Nottingham, Nottingham, UK
13 shared publications M. G. Somekh
Advanced Optics Group, Faculty of Engineering, University of Nottingham, University Park, Nottingham, NG7 2RD, United Kingdom
12 shared publicationsMatt Clark
Park University
10 shared publications- Theodosia Stratoudaki
Electronic & Electrical Engineering, University of Strathclyde, Glasgow, UK
9 shared publications Wenqi Li
8 shared publications
Latest Publications
- Open Access
- 1 February 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (5) , 051102
Single pixel camera methodologies for spatially resolved acoustic spectroscopy
Spatially resolved acoustic spectroscopy (SRAS) is a laser ultrasound technique used to determine the crystallographic orientation (i.e., microstructure) of materials through the generation and measurement of surface acoustic wave velocity on a sample. Previous implementations have used a grating pattern imaged onto the surface to control the frequency of the generated wave in a single direction—grain orientation can be computed by acquiring wave velocities in different directions on the surface (gathered by physically rotating the grating pattern). This paper reports an advance to this methodology, inspired by single pixel cameras, using a coded grating pattern, created using a spatial light modulator, to excite surface acoustic waves in multiple directions simultaneously. This change to the optical arrangement can simplify the overall system alignment, remove mechanical complexities, and is well suited for point-by-point full orientation imaging, potentially allowing for faster orientation imaging using SRAS microscopy. Improvements to the robustness of measurement may be expected to extend the applicability of SRAS in the materials science field. To demonstrate this methodology, experiments were conducted on isotropic and anisotropic samples.
- 1 February 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (5) , 051102
Open AccessSingle pixel camera methodologies for spatially resolved acoustic spectroscopy
Spatially resolved acoustic spectroscopy (SRAS) is a laser ultrasound technique used to determine the crystallographic orientation (i.e., microstructure) of materials through the generation and measurement of surface acoustic wave velocity on a sample. Previous implementations have used a grating pattern imaged onto the surface to control the frequency of the generated wave in a single direction—grain orientation can be computed by acquiring wave velocities in different directions on the surface (gathered by physically rotating the grating pattern). This paper reports an advance to this methodology, inspired by single pixel cameras, using a coded grating pattern, created using a spatial light modulator, to excite surface acoustic waves in multiple directions simultaneously. This change to the optical arrangement can simplify the overall system alignment, remove mechanical complexities, and is well suited for point-by-point full orientation imaging, potentially allowing for faster orientation imaging using SRAS microscopy. Improvements to the robustness of measurement may be expected to extend the applicability of SRAS in the materials science field. To demonstrate this methodology, experiments were conducted on isotropic and anisotropic samples.
- Open Access
- 1 March 2019
- Published by British Institute of Non-Destructive Testing (BINDT) in Insight - Non-Destructive Testing and Condition Monitoring
- Vol. 61 (3) , 132-137
Spatially Resolved Acoustic Spectroscopy Towards Online Inspection of Additive Manufacturing
High-integrity engineering applications such as aerospace will not permit the incorporation of components containing any structural defects. The current generation of additive manufacturing (AM) platforms yield components with relatively high levels of defects. The in-line inspection of components built using AM can provide closed-loop feedback and vary build parameters during fabrication to minimise defects. This article reviews the capability of spatially resolved acoustic spectroscopy (SRAS) to be used as an inspection tool for detecting defects and characterising microstructure in parts induced by variations in build parameters. The authors first correlated changes to surface acoustic wave velocity and an increase in defects to variations in build laser power, then identified changes to the component microstructure caused by variations in build laser scan strategy. This was carried out using the detected probe light intensity and the measured surface acoustic velocity.
- 1 March 2019
- Published by British Institute of Non-Destructive Testing (BINDT) in Insight - Non-Destructive Testing and Condition Monitoring
- Vol. 61 (3) , 132-137
Open AccessSpatially Resolved Acoustic Spectroscopy Towards Online Inspection of Additive Manufacturing
High-integrity engineering applications such as aerospace will not permit the incorporation of components containing any structural defects. The current generation of additive manufacturing (AM) platforms yield components with relatively high levels of defects. The in-line inspection of components built using AM can provide closed-loop feedback and vary build parameters during fabrication to minimise defects. This article reviews the capability of spatially resolved acoustic spectroscopy (SRAS) to be used as an inspection tool for detecting defects and characterising microstructure in parts induced by variations in build parameters. The authors first correlated changes to surface acoustic wave velocity and an increase in defects to variations in build laser power, then identified changes to the component microstructure caused by variations in build laser scan strategy. This was carried out using the detected probe light intensity and the measured surface acoustic velocity.
- Open Access
- 1 November 2017
- Published by Elsevier in Scripta Materialia
- Vol. 140, 67-70
Orientation imaging of macro-sized polysilicon grains on wafers using spatially resolved acoustic spectroscopy
- 1 November 2017
- Published by Elsevier in Scripta Materialia
- Vol. 140, 67-70
Open AccessOrientation imaging of macro-sized polysilicon grains on wafers using spatially resolved acoustic spectroscopy
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Experimental setup of continuous ultrasonic monitoring for corrosion assessment
The paper is devoted to the ultrasonic monitoring of accelerated corrosion. In order to achieve non-uniform corrosion (high surface roughness), passivation was applied to the corroding surface. A dedicated electronic multiplexed four channel front end was developed in order to feed the amplified waveforms from several transducers to the recording instrument. The experiment was conducted using two 5 MHz and two 10 MHz ultrasonic transducers all operating in the pulse echo mode. The transducers were excited in turn using gated bursts, and the received echoes were multiplexed and amplified before being digitized by a high accuracy ultrasonic instrument. Application of adaptive cross correlation to the recorded data allowed continuous thickness estimation of the non-uniformly corroded surface whilst cross correlation method gave unsatisfactory results.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Experimental setup of continuous ultrasonic monitoring for corrosion assessment
The paper is devoted to the ultrasonic monitoring of accelerated corrosion. In order to achieve non-uniform corrosion (high surface roughness), passivation was applied to the corroding surface. A dedicated electronic multiplexed four channel front end was developed in order to feed the amplified waveforms from several transducers to the recording instrument. The experiment was conducted using two 5 MHz and two 10 MHz ultrasonic transducers all operating in the pulse echo mode. The transducers were excited in turn using gated bursts, and the received echoes were multiplexed and amplified before being digitized by a high accuracy ultrasonic instrument. Application of adaptive cross correlation to the recorded data allowed continuous thickness estimation of the non-uniformly corroded surface whilst cross correlation method gave unsatisfactory results.
- 15 March 2017
- Published by Wiley in Journal of Microscopy
- Vol. 267 (1) , 89-97
Comparison of grain to grain orientation and stiffness mapping by spatially resolved acoustic spectroscopy and EBSD
Our aim was to establish the capability of spatially resolved acoustic spectroscopy (SRAS) to map grain orientations and the anisotropy in stiffness at the sub-mm to micron scale by comparing the method with electron backscatter diffraction (EBSD) undertaken within a scanning electron microscope. In the former the grain orientations are deduced by measuring the spatial variation in elastic modulus; conversely, in EBSD the elastic anisotropy is deduced from direct measurements of the crystal orientations. The two test-cases comprise mapping the fusion zones for large TIG and MMA welds in thick power plant austenitic and ferritic steels, respectively; these are technologically important because, among other things, elastic anisotropy can cause ultrasonic weld inspection methods to become inaccurate because it causes bending in the paths of sound waves. The spatial resolution of SRAS is not as good as that for EBSD (∼100 m vs. ∼a few nm), nor is the angular resolution (∼1.5° vs. ∼0.5°). However the method can be applied to much larger areas (currently on the order of 300 mm square), is much faster (∼5 times), is cheaper and easier to perform, and it could be undertaken on the manufacturing floor. Given these advantages, particularly to industrial users, and the on-going improvements to the method, SRAS has the potential to become a standard method for orientation mapping, particularly in cases where the elastic anisotropy is important over macroscopic/component length scales. Although for many engineering applications it is acceptable to assume that materials are homogeneous at the macroscale, in reality materials are highly anisotropic at the micron scale. Metallic materials generally comprise many small crystalline regions, called grains, each differently oriented and having different properties (such as stiffness) in different directions. In this paper we compare two methods for determining the polycrystalline microstructure of materials; one highly novel (SRAS) and the other a benchmark standard (EBSD). The current standard method for determining the orientation of the grains in a material is electron backscatter diffraction (EBSD). In EBSD a beam of electrons is scanned across a material surface. This interacts with the material and the diffracted beam is detected. The characteristics of the diffracted beam reveal details of the orientation of the crystal beneath the beam. In the new method, spatially resolved acoustic spectroscopy (SRAS), a laser directed through a grating at the material excites elastic waves in the surface, which are detected nearby. The characteristics of the waves are related to the stiffness of the material in different directions. In both methods the beam/laser is scanned across the material surface to collect information at hundreds of points, which make up a map of the material orientation across the surface. One reason to collect such maps is for the correction of ultrasonic flaw detection signals from inspection of large welds, for example. In ultrasonic inspection, sound waves are sent through the weld and, by measuring their time-of-flight and intensity upon exit, variations in their path caused by flaws can be detected. Models of the paths are created and fit to the data to accurately locate the flaws. Problems arise when inconsistencies in the ‘solid’ (unflawed) material cause path changes that confuse the location of the flaw. Variations in the stiffness of the material in the path direction due to the variations in orientation of the structure, coupled with different stiffnesses for different directions in the structure, cause such problems. In these cases, stiffness maps of the weld cross-sections, determined from orientation maps and structure stiffness data, are incorporated into the fitting models. The two samples we characterized were sections cut through thick, multipass welds in power-plant steels. We determined that SRAS is a good method for measuring the maps required to correct ultrasonic flaw detection signals. EBSD has better spatial and angular resolution, but SRAS is faster, requires less preparation of the material surface and can accept larger and more irregularly shaped samples; also, the resolution of SRAS is easily sufficient. There is excellent potential for SRAS to become a standard inspection technique.- 15 March 2017
- Published by Wiley in Journal of Microscopy
- Vol. 267 (1) , 89-97
Comparison of grain to grain orientation and stiffness mapping by spatially resolved acoustic spectroscopy and EBSD
Our aim was to establish the capability of spatially resolved acoustic spectroscopy (SRAS) to map grain orientations and the anisotropy in stiffness at the sub-mm to micron scale by comparing the method with electron backscatter diffraction (EBSD) undertaken within a scanning electron microscope. In the former the grain orientations are deduced by measuring the spatial variation in elastic modulus; conversely, in EBSD the elastic anisotropy is deduced from direct measurements of the crystal orientations. The two test-cases comprise mapping the fusion zones for large TIG and MMA welds in thick power plant austenitic and ferritic steels, respectively; these are technologically important because, among other things, elastic anisotropy can cause ultrasonic weld inspection methods to become inaccurate because it causes bending in the paths of sound waves. The spatial resolution of SRAS is not as good as that for EBSD (∼100 m vs. ∼a few nm), nor is the angular resolution (∼1.5° vs. ∼0.5°). However the method can be applied to much larger areas (currently on the order of 300 mm square), is much faster (∼5 times), is cheaper and easier to perform, and it could be undertaken on the manufacturing floor. Given these advantages, particularly to industrial users, and the on-going improvements to the method, SRAS has the potential to become a standard method for orientation mapping, particularly in cases where the elastic anisotropy is important over macroscopic/component length scales. Although for many engineering applications it is acceptable to assume that materials are homogeneous at the macroscale, in reality materials are highly anisotropic at the micron scale. Metallic materials generally comprise many small crystalline regions, called grains, each differently oriented and having different properties (such as stiffness) in different directions. In this paper we compare two methods for determining the polycrystalline microstructure of materials; one highly novel (SRAS) and the other a benchmark standard (EBSD). The current standard method for determining the orientation of the grains in a material is electron backscatter diffraction (EBSD). In EBSD a beam of electrons is scanned across a material surface. This interacts with the material and the diffracted beam is detected. The characteristics of the diffracted beam reveal details of the orientation of the crystal beneath the beam. In the new method, spatially resolved acoustic spectroscopy (SRAS), a laser directed through a grating at the material excites elastic waves in the surface, which are detected nearby. The characteristics of the waves are related to the stiffness of the material in different directions. In both methods the beam/laser is scanned across the material surface to collect information at hundreds of points, which make up a map of the material orientation across the surface. One reason to collect such maps is for the correction of ultrasonic flaw detection signals from inspection of large welds, for example. In ultrasonic inspection, sound waves are sent through the weld and, by measuring their time-of-flight and intensity upon exit, variations in their path caused by flaws can be detected. Models of the paths are created and fit to the data to accurately locate the flaws. Problems arise when inconsistencies in the ‘solid’ (unflawed) material cause path changes that confuse the location of the flaw. Variations in the stiffness of the material in the path direction due to the variations in orientation of the structure, coupled with different stiffnesses for different directions in the structure, cause such problems. In these cases, stiffness maps of the weld cross-sections, determined from orientation maps and structure stiffness data, are incorporated into the fitting models. The two samples we characterized were sections cut through thick, multipass welds in power-plant steels. We determined that SRAS is a good method for measuring the maps required to correct ultrasonic flaw detection signals. EBSD has better spatial and angular resolution, but SRAS is faster, requires less preparation of the material surface and can accept larger and more irregularly shaped samples; also, the resolution of SRAS is easily sufficient. There is excellent potential for SRAS to become a standard inspection technique.- Open Access
- 1 January 2017
- Published by Elsevier in Additive Manufacturing
- Vol. 13, 135-142
Assessing the capability of in-situ nondestructive analysis during layer based additive manufacture
- 1 January 2017
- Published by Elsevier in Additive Manufacturing
- Vol. 13, 135-142
Open AccessAssessing the capability of in-situ nondestructive analysis during layer based additive manufacture
- Top Cited PapersOpen Access
- 1 October 2016
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 236, 93-102
Spatially resolved acoustic spectroscopy for selective laser melting
- 1 October 2016
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 236, 93-102
Top Cited PapersOpen AccessSpatially resolved acoustic spectroscopy for selective laser melting
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 147-152
Design and experimental evaluation of a test rig for ultrasonic monitoring of accelerated corrosion
The design of a test rig for ultrasonic monitoring of corroding steel samples and results of its experimental evaluation are presented. In order to accelerate and quantify corrosion, the monitored sample acts as an anode in a typical constant current electroplating setup. An Arduino-powered microcontroller is used to log the relevant voltage and current values on an SD card, and a high accuracy ultrasonic waveform acquisition instrument is employed to record the ultrasonic waveforms reflected form the corroding surface. Experimental assessment of the designed rig confirmed that it met the design objectives and could be used for experimental studies of accelerated corrosion in steel samples.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 147-152
Design and experimental evaluation of a test rig for ultrasonic monitoring of accelerated corrosion
The design of a test rig for ultrasonic monitoring of corroding steel samples and results of its experimental evaluation are presented. In order to accelerate and quantify corrosion, the monitored sample acts as an anode in a typical constant current electroplating setup. An Arduino-powered microcontroller is used to log the relevant voltage and current values on an SD card, and a high accuracy ultrasonic waveform acquisition instrument is employed to record the ultrasonic waveforms reflected form the corroding surface. Experimental assessment of the designed rig confirmed that it met the design objectives and could be used for experimental studies of accelerated corrosion in steel samples.
- Open Access
- 1 January 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 684 (1) , 012001
Crystallographic Orientation Determination of Hexagonal Structure Crystals by Laser Ultrasonic Technique
Spatially resolved acoustic spectroscopy (SRAS) is a laser ultrasonic technique that shows qualitative contrast between grains of different orientation, illustrating the sensitivity of acoustic waves to the material structure. The technique has been improved significantly on determining the full orientation of multigrain cubic metals, by comparing the measured surface acoustic wave (SAW) velocity to a pre-calculated model. In this paper we demonstrate the ability of this technique to determine the orientation of hexagonal structure crystals, such as magnesium and titanium based alloys. Because of the isotropy of the SAW velocity on the basal plane (0001) of hexagonal crystals, the slowness surface is shown as a circle. As the plane moves from (0001) towards (11 20) or towards (10 10), the slowness surface gradually turns into an oval. These acoustic properties increase the difficulty in orientation determination. The orientation results of a grade 1 commercially pure titanium by SRAS is presented, with comparison with electron backscattered diffraction (EBSD) results. Due to the nature of SAWs on hexagonal structure crystals, only the results of Euler angles 1 and 2 are discussed. The error between SRAS and EBSD is also investigated.
- 1 January 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 684 (1) , 012001
Open AccessCrystallographic Orientation Determination of Hexagonal Structure Crystals by Laser Ultrasonic Technique
Spatially resolved acoustic spectroscopy (SRAS) is a laser ultrasonic technique that shows qualitative contrast between grains of different orientation, illustrating the sensitivity of acoustic waves to the material structure. The technique has been improved significantly on determining the full orientation of multigrain cubic metals, by comparing the measured surface acoustic wave (SAW) velocity to a pre-calculated model. In this paper we demonstrate the ability of this technique to determine the orientation of hexagonal structure crystals, such as magnesium and titanium based alloys. Because of the isotropy of the SAW velocity on the basal plane (0001) of hexagonal crystals, the slowness surface is shown as a circle. As the plane moves from (0001) towards (11 20) or towards (10 10), the slowness surface gradually turns into an oval. These acoustic properties increase the difficulty in orientation determination. The orientation results of a grade 1 commercially pure titanium by SRAS is presented, with comparison with electron backscattered diffraction (EBSD) results. Due to the nature of SAWs on hexagonal structure crystals, only the results of Euler angles 1 and 2 are discussed. The error between SRAS and EBSD is also investigated.
- 1 November 2015
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 138 (5) , 2811-2819
Imaging textural variation in the acoustoelastic coefficient of aluminum using surface acoustic waves
Much interest has arisen in nonlinear acoustic techniques because of their reported sensitivity to variations in residual stress, fatigue life, and creep damage when compared to traditional linear ultrasonic techniques. However, there is also evidence that the nonlinear acoustic properties are also sensitive to material microstructure. As many industrially relevant materials have a polycrystalline structure, this could potentially complicate the monitoring of material processes when using nonlinear acoustics. Variations in the nonlinear acoustoelastic coefficient on the same length scale as the microstructure of a polycrystalline sample of aluminum are investigated in this paper. This is achieved by the development of a measurement protocol that allows imaging of the acoustoelastic response of a material across a samples surface at the same time as imaging the microstructure. The development, validation, and limitations of this technique are discussed. The nonlinear acoustic response is found to vary spatially by a large factor (>20) between different grains. A relationship is observed when the spatial variation of the acoustoelastic coefficient is compared to the variation in material microstructure.
- 1 November 2015
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 138 (5) , 2811-2819
Imaging textural variation in the acoustoelastic coefficient of aluminum using surface acoustic waves
Much interest has arisen in nonlinear acoustic techniques because of their reported sensitivity to variations in residual stress, fatigue life, and creep damage when compared to traditional linear ultrasonic techniques. However, there is also evidence that the nonlinear acoustic properties are also sensitive to material microstructure. As many industrially relevant materials have a polycrystalline structure, this could potentially complicate the monitoring of material processes when using nonlinear acoustics. Variations in the nonlinear acoustoelastic coefficient on the same length scale as the microstructure of a polycrystalline sample of aluminum are investigated in this paper. This is achieved by the development of a measurement protocol that allows imaging of the acoustoelastic response of a material across a samples surface at the same time as imaging the microstructure. The development, validation, and limitations of this technique are discussed. The nonlinear acoustic response is found to vary spatially by a large factor (>20) between different grains. A relationship is observed when the spatial variation of the acoustoelastic coefficient is compared to the variation in material microstructure.