DZDaqing Zhou

Daqing Zhou

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Daqing Zhou has a total of 63 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Hydraulic Characteristics Analysis of Free-Surface-Pressurized Flow in Long Tailrace Systems Under Variable Load Conditions

    byĀ Yuguo Zhou, Xin He, Daqing Zhou, Xiaoliang Li, An Yu, Ling Zhou

    Complex hydraulic transients induced during load adjustment of turbine units in long tailrace tunnels pose significant threats to the safety and stability of tailwater systems. In view of this, based on VOF multiphase flow and compressible water–air models, a three-dimensional full-flow-channel numerical model of long tailrace system incorporating surge shaft and downstream river channel was developed using computational fluid dynamics (CFD) software to explore the transient impact of load changes on flow rate, water level, and pressure pulsations under different flow regimes in the tailrace tunnel, including open channel flow, pressurized flow, and free-surface-pressurized flow. The results indicate that the discharge at the outlet of the tailrace tunnel exhibits attenuated oscillations in response to load variations, with the most severe fluctuations occurring due to the intense air–water interface mixing during free-surface-pressurized flow. Flow regime transitions are accompanied by air pocket phenomena, resulting in significant fluctuations in air volume fraction. Pressure pulsations show periodic variations, with energy gradually dissipating as they propagate downstream. Open channel flows predominantly feature high-frequency waves, while pressurized flows exhibit intense low-frequency pulsations. Additionally, load changes in one unit have an ultra-low-frequency impact on another unit sharing the same tailrace tunnel, with high-frequency waves being filtered out by the surge shaft.


  • Open Access

    Cavitation Performance Variation in Adjacent Francis Turbine Induced by Single Load Rejection

    byĀ Haobo Wang, Daqing Zhou, An Yu, Junxun Guo

    When multiple Francis turbines share a common tailwater surge chamber, the load rejection transient process of one turbine can significantly influence the cavitation performance of the adjacent turbine. To investigate this phenomenon, a three-dimensional full-flow system model is established in this study. Numerical simulations based on the finite volume method (FVM) are conducted to analyze the cavitation evolution within the affected turbine, with pressure pulsation variations monitored at multiple key locations during load rejection. The numerical simulation results reveal that during the load rejection process of a single turbine, the pressure distribution in the draft tube of the adjacent turbine is directly affected, resulting in varying degrees of cavitation intensification in both the runner and draft tube. Additionally, a dominant pressure pulsation frequency of 0.31Hz is observed at the monitoring points inside the affected turbine.

  • Numerical investigation of the fluid dynamic properties in ventilated cavitation around an underwater vehicle

    byĀ An Yu, Liting Li, Siqin Yan, Yuquan Zhang, Daqing Zhou

    Ventilated cavitation is a complex flow phenomenon that involves multi-phase flow, coupled vortex evolution, and turbulent pulsation. This paper employs the large eddy simulation method to systematically investigate the ventilated cavitation flow of an underwater vehicle equipped with a disk cavitator. The results indicate that the ventilation rate (Cq) significantly influences the cavity morphology and drag. It was observed that the closure mode of the ventilated cavity transitioned consistently with increasing Cq under Fr = 10.2, shifting from a reentrant jet to a twin vortex tube. Additionally, the key factors contributing to the formation of the twin vortex tube have been identified, which is the effects of gravity and local adverse pressure gradient. Furthermore, mechanical properties in twin vortex closure mode were analyzed, finding that the vehicle's drag and stability were influenced by the shedding of vortex structures and the dynamic deformation of the gas–liquid interface. Finally, the distribution characteristics of the modal vortex force were analyzed using the proper orthogonal decomposition method, providing a theoretical foundation for optimizing the lift and drag distribution of the vehicle.

  • Systematic evaluation of PANS-based turbulence models in separated flows at different resolved scales

    byĀ Haobo Wang, Daqing Zhou, An Yu, Junxun Guo

    Accurately simulating flow separation across multiple scales remains a major challenge in computational fluid dynamics, primarily due to the complex interactions of multi-scale vortex structures and transitional processes within the boundary layer. The Partially Averaged Navier–Stokes (PANS) method is employed in this study to investigate two representative separated flow cases: the backward-facing step flow and the flow around a square cylinder. The predictive performance of the PANS k-ε and PANS k-ω turbulence models is evaluated under various values of the unresolved-to-total kinetic energy ratio fk. Results show that with appropriate mesh resolution and cutoff scales, the PANS method can effectively capture key characteristics of multi-scale flow separation and coherent wake, while offering improved computational efficiency. For the backward-facing step flow, both models are able to reproduce the velocity distribution. In the near-wall region (y<1.5H), however, the PANS k-ω model provides better agreement with experimental data, attributed to its treatment of adverse pressure gradients. For large-scale separated flows, the PANS method is capable of accurately resolving the majority of turbulence development within the wake region. The main discrepancies arise near the initial vortex formation zone, where the flow structure is inherently complex and unsteady. In addition, by reducing the cutoff parameter below a critical threshold, the coexistence of the dominant KĆ”rmĆ”n vortex shedding frequency (fvs) and the Kelvin–Helmholtz instability frequency (fKH) can be captured when the fk values is reduced below a critical threshold.


  • The enstrophy dissipation in the cavitating flow based on the proper orthogonal decomposition

    byĀ An Yu, Wenjin Feng, Zhaohui Qian, Daqing Zhou

    This study employs the large eddy simulation method to investigate the intricate interplay between the vortex and entropy production in the cavitating flow. Results indicate that the instantaneous total entropy production loss is essentially induced by local enstrophy dissipation of the local vortex structures. The derived Enstrophy term of entropy production rate can be regarded as the simplified entropy production rate (EPR) formula. Analysis of the generation and transportation of enstrophy further reveals the high-value regions of each term of enstrophy mainly concentrated at the vapor–liquid interface, reflecting the influence of the instability of cavities on the formation and dissipation of vortex structures. Based on the simplified EPR formula, the proper orthogonal decomposition (POD) approach is utilized to obtain the coherent structures that dominate the enstrophy dissipation scales in the cavitating flow. The findings reveal that the first four dominant POD modes account for 95.8% of the modal enstrophy dissipation of EPR, and mode 2 captured the large-scale shedding structures at the trailing edge. The frequency of mode 2 and mode 3 approximates the cavity shedding frequency. Additionally, the interaction between the mode enstrophy dissipation of EPR and mode vortex structures is expounded that the magnitude of energy dissipation of EPR carried by mode vortex structures attenuate and the spatial scales of structures decrease with the orders of mode increase. Furthermore, POD reduction technology constructs 95.8% and 99.1% of the original total enstrophy dissipation of EPR, which well resolved the variation of the enstrophy dissipation concentrated at the instability cavity interface and the end of the cavity while eliminating the effect of the small-scale structures with an acceptable accuracy effectively. This study provides a valuable understanding of the coupling mechanism between modal entropy generation and vortex structures of different modal scales in the cavitating flow.

  • A new single-phase flow algorithm for enabling water level regulation in surge shafts

    byĀ Junxun Guo, Daqing Zhou, Haobo Wang

    Surge shafts play a role in stabilizing pressure in long-distance water pipeline systems. However, to accurately simulate its regulatory function in three-dimensional numerical simulations, a multiphase flow model that demands substantial computational resources is necessary. Through secondary development of software, the implementation of a single-phase flow surge shaft model was achieved. By comparing the calculation results of the multiphase flow model, the accuracy and feasibility of the single-phase flow calculation method were verified. The results indicate that the single-phase simulation method could accurately capture the water level variation pattern. Deviations within an acceptable range only occur during water level drawdown. Furthermore, minor differences in velocity distribution between the two methods exist solely within the impedance hole channel, and the pressure field was in good agreement. The pressure pulsation deviation of all monitoring points was below 2.5%, and in the long pipeline, it was less than 0.5%. The correlation coefficients of key monitoring points, especially those inside the pipeline, were higher than 0.98, indicating a high correlation and confirming the high reliability of the simplified single-phase flow method for practical applications. This study demonstrates that the approach is a viable and accurate tool for simulating surge shaft behavior in pipeline systems.


  • Open Access

    Investigations into Hydraulic Instability during the Start-Up Process of a Pump-Turbine under Low-Head Conditions

    byĀ Tingzheng Wang, Chuqiao Yu, Haocheng Yang, Yilin Zhao, Yibo Zhou, Hanzhong Liu, Daqing Zhou, Kan Kan

    To investigate the hydraulic characteristics during the start-up process of a full-flow pumped storage unit under low-head conditions, numerical simulations were conducted to study the dynamic characteristics during the process, providing a detailed analysis of the dynamic behavior of the internal flow field during the transition period as well as the associated variation in external performance parameters. Study results revealed a vortex-shedding phenomenon during the initial phase of the start-up process. These vortices restrict the flow, initiating a water hammer effect that abruptly elevates the upstream pressure within the runner. As the high-pressure water hammer dissipated, the flow rate rapidly increased, leading to a secondary but relatively weaker water hammer effect, which caused a momentary drop in pressure. This series of events ultimately resulted in significant oscillations in the unit’s head. After the guide vanes stop opening, the vortex structures at the runner inlet and outlet gradually weaken. As the runner torque continues to decline, the unit gradually approaches a no-load condition and enters the S-shaped region. Concurrently, pressure pulsations intensify, and unstable vortex formations reemerge along the leading and trailing edges of the runner blades. The escalated flow velocity at the runner’s exit contributes to the elongation of the vortex band within the draft tube, ultimately configuring a double-layer vortex structure around the central region and the pipe walls. This configuration of vortices precipitates the no-load instability phenomenon experienced by the unit.


  • Open Access

    Study of intermittent jets and free-surface-pressurized flow in large hydropower tailrace tunnel

    byĀ Junxun Guo, Daqing Zhou, Haobo Wang

    The tailrace tunnel system, as a core component of hydroelectric power stations, directly influences the stability and efficiency of the power generation process. Transient conditions often lead to the occurrence of complex unsteady flow phenomena in the tailrace tunnel. In this study, numerical methods integrating open channel flow, multiphase flow, and compressible models were combined to conduct hydraulic analysis of the tailrace system in large hydroelectric power stations. Under specific conditions, periodic jet phenomena were observed, corroborating field observations. The research revealed that the proximity of downstream water levels to the crest level of the tailrace outlet is a prerequisite for the periodic jetting phenomenon, with a sudden rise in water level serving as a triggering condition. Although the surge shaft effectively mitigates wave action, it fails to entirely eliminate the influence of pressure pulsations, resulting in a 23.2% increase in pressure pulsation amplitude in the turbine area. However, the efficiency of the turbine unit is hardly affected; only a slight loss of energy occurs due to the increase in local turbulent entropy production, deemed inconsequential for the overall system. This study aims to investigate the complex response of tailrace tunnel systems in hydroelectric power generation amidst abrupt changes in downstream river, providing crucial insights for the engineering design and operation of large-scale power stations.


  • Open Access

    Analysis of Cavitation-Induced Unsteady Flow Conditions in Francis Turbines under High-Load Conditions

    byĀ Haobo Wang, Daqing Zhou, An Yu, Junxun Guo

    Hydraulic vibrations in Francis turbines caused by cavitation profoundly impact the overall hydraulic performance and operational stability. Therefore, to investigate the influence of cavitation phenomena under high-load conditions, a three-dimensional unsteady numerical simulation is carried out for a Francis turbine with different head operating conditions, which is combined with the SST k-w turbulence model and two-phase flow cavitation model to capture the evolution of cavitation under high-load conditions. Additionally, utilizing entropy production theory, the hydraulic losses of the Francis turbine during cavitation development are assessed. Contrary to the pressure-drop method, the entropy production theory can quantitatively reflect the characteristics of the local hydraulic loss distribution, with a calculated error coefficient Ļ„ not exceeding 2%. The specific findings include: the primary sources of energy loss inside the turbine are the airfoil cavitation and cavitation vortex rope, constituting 26% and 71% of the total hydraulic losses, respectively. According to the comparison with model tests, the vapor volume fraction (VVF) inside the draft tube fluctuates periodically under high-load conditions, causing low-frequency pressure pulsation in the turbine’s power, flow rate, and other external characteristic parameters at 0.37 Hz, and the runner radial force fluctuates at a frequency of 1.85 Hz.


  • Open Access

    Analysis of Hydraulic Losses in Vortex Rope Inside the Draft Tube of Francis Pump-Turbine Based on Entropy Production Theory

    byĀ Haobo Wang, Daqing Zhou, Junxun Guo, Lianchen Xu

    The existence of vortex ropes inside the draft tube significantly impacts hydraulic efficiency and operational stability, and few studies on the formation mechanism of vortex ropes and hydraulic loss problems have been explored. Hence, in this paper, we build an inherent correlation between the local entropy production rate (LEPR) in the draft tube and the dynamics of vortex motion, by incorporating the vortex identification method Ω~R with entropy production theory, using the OpenFOAM-v2212 software. From the analysis of the entropy production theory, the entropy production rate caused by turbulence dissipation (EPTD) is responsible for the majority of energy loss in the form of entropy production rate, accounting for about 87% of the total entropy production rate (TEPR) in different load operations. Comparatively, the entropy production rate caused by wall shear stress (EPWS) can account for up to 12%, while the entropy production rate due to direct dissipation (EPDD) plays a minor role in TEPR. The rotating vortex rope movement of the unit at part load conditions leads to more intense LEPR. Therefore, to determine the hydraulic loss caused by the vortex rope, the TEPR at the cross-section can be used to assess the hydraulic characteristics of the draft tube.