JHJongsoo Hwang

Jongsoo Hwang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jongsoo Hwang has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Containment of Water-Injection-Induced Fractures: The Role of Heat Conduction and Thermal Stresses

    by Jongsoo Hwang, Shuang Zheng, Mukul Sharma, Maria-Magdalena Chiotoroiu, Torsten Clemens

    Summary: Reservoir cooling by water or wastewater injection can significantly change the stress in the target injection zones and the bounding layers. Out-of-zone fracture growth is substantially affected by these poro-thermo-elastic stress changes occurring in heterogeneous rock layers. No previous study has systematically investigated the influence of both heat conduction and convection and the associated stress alteration and fracture height growth during long-term water injection in multiple layers. Without understanding this coupled effect, it is not possible to predict the injection-induced fracture geometry or the conditions under which these fractures will breach the bounding shale layers. This paper presents a model and results that clearly show that accounting for thermal conduction between the injection sand and the bounding shale is crucial in predicting fracture containment during water injection. We developed a fully coupled compositional reservoir/fracturing simulator that solves poro-thermo-elastic equations. We used it to simulate 3D fracture propagation induced by cold water injection and, at the same time, calculate changes in the stress field induced by thermo-poro-elastic effects in heterogeneous reservoir layers. The stress in the bounding layer is shown to change significantly as a result of thermal conduction from the layer below. We first validate our model with existing analytical solutions and then present synthetic cases and simulate a field case. Simulation results show that fracture height growth can be underpredicted if heat conduction between the target injection sands and bounding shales is ignored. We identify the effects of fluid properties, rock properties, and injection temperature on thermal-conduction-induced stress changes and fracture containment for the first time.


  • Containment of Water-Injection-Induced Fractures: The Role of Heat Conduction and Thermal Stresses

    by Jongsoo Hwang, Shuang Zheng, Mukul Sharma, Maria-Magdalena Chiotoroiu, Torsten Clemens

    Reservoir cooling by water or waste-water injection can significantly alter the reservoir stress. The out- of-zone fracture growth is substantially affected by this poro-thermo-elastic stress changes occurring in heterogeneous rock layers. No previous study, however, systematically investgated the influence of heat conduction and convection on the associated stress alteration and fracture height growth during the long- term water injection in multiple layers. Without understanding this coupled effect, which occurs over a long-term fracture propagation, it is difficult to capture the conditions for the fractures to breach into the bounding shale layers. In this paper, we present that the thermal conduction between the injection sand and bounding shale is crucial in predicting the fracture containment during water injection. We developed a fully coupled compositional reservoir/fracturing simulator that solves poro-thermo-elasticity. We used it to simulate 3- dimensional fracture propagation induced by cold water injection and, at the same time, calculate the stress field influenced by the thermo-poro-elastic effect in heterogeneous reservoir layers. Effective stress in the bounding layer is dynamically updated to capture the poro-thermo-elastic effect and associated fracture height growth. We first validate our model with existing analytical solutions and studied a field case. We identify the effects of fluid properties, rock properties, and injection temperature on stress changes and the fracture containment for the first time.


  • Risk Assessment and Simulation of Injectivity Decline Under Uncertainty

    by Maria-Magdalena Chiotoroiu, Torsten Clemens, Markus Zechner, Jongsoo Hwang, Mukul M. Sharma, Marco Thiele

    Waterflooding can lead to substantial incremental oil production. Implementation of water-injection projects requires the project to fit into the risk (defined here as negative outcomes relative to defined project objectives) and uncertainty (defined here as the inability to estimate a value precisely) a company is willing to take. One of the key risks for water injection into a shallow reservoir is injection-induced fractures extending into the caprock. If this risk is seen as “intolerable” in an as-low-as-reasonably-practicable (ALARP) analysis, a decision might be made not to proceed with the project. In this study, we evaluated caprock integrity by conducting simulations of long-term water injection that include the effects of formation damage caused by internal/external plugging, geomechanical stress changes, and fracture propagation in the sandstone and bounding shale. The risk of fracture growth into the caprock was assessed by conducting Latin hypercube sampling considering a set of modeling parameters each associated with an uncertainty range. This allowed us to identify the range of operating parameters in which the risk of fracture-height growth was acceptable. Our simulations also allowed us to identify important factors that affect caprock integrity. To cover the uncertainty in geomechanical reservoir evaluation, the operating envelope is identified such that the risk to the caprock integrity is reduced. This requires introducing a limit for the bottomhole pressure (BHP), including a safety margin. The limit of the BHP is then used as a constraint in the uncertainty analysis of water injectivity. The uncertainty analysis should cover the various development options, the parameterization of the model, sampling from the distribution of parameters- and distance-based generalized sensitivity analysis (dGSA) as well as probabilistic representation of the results. The results indicate that the time to reach the BHP limit varies substantially, dependent on the chosen development scenario. Injection of water (1000 m3/d), with total suspended-solids content ranging from 0.1 to 0.5 ppm by volume (ppmv) and particle size from 1 to 5 mm, into long horizontal wells (2000 m) results in injection times of more than 10,000 days even for the P10 percentile. However, injection of poor-quality water (injection rate 600m3/d, well length 600 m), with total suspended-solids content ranging from 0.5 to 5 ppmv and particle size from 10 to 30 µm, leads to the BHP limit of 10 (P10) to 740 (P90) days. The dGSA can be used to determine which parameter has a stronger impact on the BHP and, hence, on the project, and should be measured if warranted by a value-of-information analysis. In the case reported here, dGSA showed that the filter-cake permeability has a big impact on the results and, hence, will be determined by laboratory measurements. The final development option to be chosen depends on a traditional net-present-value analysis.


  • Pre-Loading Depleted Parent Wells to Avoid Frac-Hits: Some Important Design Considerations

    by Shuang Zheng, Ripudaman Manchanda, Deepen Gala, Mukul Sharma, Jongsoo Hwang

    Mitigating the negative impact of frac-hits on production from parent and child wells is challenging. In this work, we show the impact of parent well depletion and repressurization on the child well fracture propagation and parent well productivity in different US shale reservoirs. By repressurizing the parent well, we do not imply repressurization of the entire depleted reservoir. By repressurizing the parent well, we imply pressurization of only the near fracture regions. Our goal is to develop a method to better manage production/injection in the parent well and stimulation operations in the child well to minimize frac-hits and improve oil and gas recovery. We have developed a fully implicit, 3-D, parallelized, poroelastic, compositional, reservoir-fracture simulator to seamlessly model fluid production/injection (water or gas) in the parent well and model propagation of multiple fractures from the child well (Zheng et al., 2019a; Manchanda et al., 2019a). This simulator implicitly solves for the reservoir deformation and pressure, fracture pressure and injection/production rate to quantify the stress changes due to production/injection, and also the propagation of child well fractures resulting in parent-child well interactions. Component mass balance equations and equation of state-based flash calculations are coupled with the implicit solver to account for the phase behavior in different reservoir fluids and also during the injection process. We have analyzed the effects of drawdown rate and production time in three shale plays: Permian (oil), Eagle Ford (volatile oil/gas condensate) and Haynesville (dry gas) reservoirs. The results show that different reservoir fluids and drawdown strategies for the parent wells result in different stress distributions in the depleted zone and this affects the child well fracture propagation. We studied different strategies to repressurize the parent well by varying the injected fluids (gas vs. water), pre-load fluid volumes, etc. It was found that frac-hits can be avoided if the fluid injection strategy is designed appropriately. In some poorly designed pre-loading strategies, frac-hits are still observed. Lastly, we analyzed the impact of pre-loading on the parent well productivity. When water was used for pre-loading, we observed water blocking in the reservoir that caused damage to the parent well. However, when gas was injected for pre-loading, the oil recovery of the parent well was observed to increase. We present, for the first time, fully compositional geomechanical simulations of child well fracture propagation around depleted parent wells. We study the impact of parent well production reservoir fluid, etc. on child well fracture propagation. Fluid injection (pre-loading) strategy in the parent well and subsequent avoidance of frac-hits is also modeled. Such simulations of parent-child well interactions provide much-needed quantification to predict and mitigate the damage caused by depletion and frac-hits.


  • Water Injection Well Performance and Fracture Propagation in a Channel Sand Reservoir: An Offshore Ghana Case Study

    by Jongsoo Hwang, Prateek Bhardwaj, Mukul Sharma, Sekhar Sathyamoorthy, Kwarteng Amaning, Arvinder Singh

    This study explains the large injectivity changes observed in the field, how to remedy it, and how to ensure fracture containment in channel sand reservoirs. The case study field is located offshore Ghana and is a channel sand reservoir. Water injection was initiated for pressure maintenance and waterflooding under fracturing conditions. The injection wells are designed to ensure high and sustainable injection rates while maintaining the integrity of the cap rock. The injection bottom-hole pressure (BHP) was history-matched to investigate the impact of stress profiles, reservoir shapes, injection water quality, poroelastic and thermally induced stress changes. The injectivity decline was found to be a result of changes in stresses caused by the channel boundaries and, to a lesser extent, near-wellbore formation damage. The rapid increase in pore pressure and the resulting decrease in injectivity is unique to these kinds of channel sands. Once the origin of the decreasing injectivity was identified, remedial actions were recommended and predictions for future injectivity were made ensuring containment of fractures.


  • Sand Production Caused by Water-Hammer Events: Implications for Shut-In Protocols and Design of Water-Injection Wells

    by Haotian Wang, Jongsoo Hwang, Mukul M. Sharma

    Summary: A pressure pulse, known as a water hammer, can occur immediately after water-injection wells are shut-in for emergency or operational reasons. Large pressure pulses may cause wellbore-integrity problems such as sandface failure and sand production. We propose a new work flow to simulate water-hammer events, the resulting wellbore failure, and sand production in water injectors. On the basis of the results of this work flow, recommendations are made for wellbore design and shut-in protocols for water-injection wells. For the first time, the results presented in this paper allow us to quantitatively understand the role of well shutdowns and subsequent water-hammer pressures on sand production. The failure of unconsolidated sands near the wellbore is affected by water-hammer events and their amplitude, period, and attenuation. If a water-hammer event occurs during the shut-in of water injectors, the extent of the sand failure becomes larger, and the failure zone continues to propagate along the stress-concentration direction. The simulation results clearly show the parameters that are important and suggest changes to well operations such as proper shut-in protocols that help to minimize the possibility of sand production. The results also suggest ways in which injectors can be designed to minimize the impact of water-hammer events.


  • Formation of Complex Fracture Networks in the Wolfcamp Shale: Calibrating Model Predictions with Core Measurements from the Hydraulic Fracturing Test Site

    by Kaustubh Shrivastava, Jongsoo Hwang, Mukul Sharma

    Natural fractures are a crucial factor in determining fracture and well spacing in horizontal wells. Their attributes affect the created fracture network and thereby the well producivity and EUR. However, information about the properties of natural fractures is seldom available. In this study, we used a detailed core description from the Hydraulic Fracture Test Site (HFTS), funded by the DOE and an industry consortium, to obtain in-situ natural fracture distribution data. The data was used as input into a hydraulic fracturing simulator to model fracture growth in the presence of natural fractures. The results obtained were then compared with field observations of cores taken from a slant infill well drilled into the hydraulically fractured rock. The core taken from the slant well located adjacent to the hydraulically fractured well is used to characterize the natural fractures (density and orientation). A two-dimensional discrete fracture network (DFN) is generated based on the core description. Nine coring operations are simulated on the created DFN to generate synthetic core descriptions. Attributes (length and density) of natural fractures are calibrated to match the results obtained from simulated coring operations with real core data. Multi-stage hydraulic fracturing simulations are performed using the calibrated DFN, and the results are presented in this paper. The core analysis identified three different types of fractures: hydraulic fractures, intact natural fractures, and natural fractures activated by hydraulic fractures. The density and orientations obtained from the core description provide valuable insights on the complex fracture growth behavior. The number of created fractures (propped and unpropped) far exceeds the number of perforations. This indicates the formation of complex fracture networks likely caused by the interaction of the hydraulic fracture with natural fractures and bed boundaries during propagation. A heel-side bias of fluid and proppant distribution within a stage was also observed. The effect of inter-stage stress shadowing on fracture growth could also be inferred.


  • Sand Production Caused by Water Hammer Events: Implications for Shut-In Protocols and Design of Water Injection Wells

    by Haotian Wang, Jongsoo Hwang, M. Sharma Mukul

    A pressure pulse, known as a water hammer, can occur immediately after water injection wells are shut-in for emergency or operational reasons. Large pressure pulses may cause wellbore integrity problems such as sand-face failure and sand production. We propose a new workflow to simulate water hammer events, the resulting wellbore failure and sand production in water injectors. Based on the results of this workflow, recommendations are made for wellbore design and shut-in protocols for water injection wells. The results presented in this paper, for the first time, allow us to quantitatively understand the role of well shut-downs and subsequent water hammer pressures on sand production. The failure of unconsolidated sands near the wellbore is affected by water hammer events, their amplitude, period, and attenuation. If a water hammer event occurs during shut-in of water injectors, the extent of the sand failure becomes larger and the failure zone continues to propagate along the stress concentration direction. The simulation results clearly show which parameters are important and suggest changes to well operations such as proper shut-in protocols that help to minimize the possibility of sand production. The results also suggest ways in which injectors can be designed to minimize the impact of water hammer events.