Maxim Osipov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Maxim Osipov has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
- Igor A. Rudnev
National Research Nuclear University MEPhI
21 shared publications - Sergey V. Pokrovskii
National Research Nuclear University
19 shared publications - Alexandr Starikovskii
National Research Nuclear University
16 shared publications - Dmitry Abin
National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Moscow, Russia
16 shared publications - I. V. Martirosian
National Research Nuclear University
12 shared publications - Оксана Сергеевна Руденко
All-Russian Research Institute of the Confectionery Industry
7 shared publications
Latest Publications
- Open Access
- 25 March 2026
- Published by ECO-Vector LLC (Publications) in Modern Transportation Systems and Technologies
- Vol. 12 (1) , 18-38
Superconducting bearings based on closed HTS tape windings
AIM: This work aimed to analyze the feasibility of contactless bearings based on closed high-temperature superconducting (HTS) tape windings. To study the axial load on a bearing in a wide temperature range. METHODS: The bearing load was measured using an experimental setup based on a strain gauge and a three-dimensional positioning system. The superconductor was cooled using a single-stage cryocooler. The magnetic interaction in the bearing was calculated in the COMSOL Multiphysics simulation environment. RESULTS: The relationships between the axial force and the axial shift of a superconducting bearing based on closed HTS windings were obtained for temperatures ranging from 40 to 77.4 K and shift amplitudes of 1 to 9 mm. The numerical model was verified using experimental data. Its applicability was proven for closed superconducting currents in HTS tapes. The dynamics of magnetic flux penetration into HTS windings was calculated. CONCLUSION: Closed HTS windings can be successfully used to manufacture superconducting bearings. Closed HTS windings are most effective in systems where equilibrium shifts exceeding the half-period of the magnetic array are possible. The shift magnitude at which the greatest axial restoring force is achieved increases with temperature.
- 25 March 2026
- Published by ECO-Vector LLC (Publications) in Modern Transportation Systems and Technologies
- Vol. 12 (1) , 18-38
Open AccessSuperconducting bearings based on closed HTS tape windings
AIM: This work aimed to analyze the feasibility of contactless bearings based on closed high-temperature superconducting (HTS) tape windings. To study the axial load on a bearing in a wide temperature range. METHODS: The bearing load was measured using an experimental setup based on a strain gauge and a three-dimensional positioning system. The superconductor was cooled using a single-stage cryocooler. The magnetic interaction in the bearing was calculated in the COMSOL Multiphysics simulation environment. RESULTS: The relationships between the axial force and the axial shift of a superconducting bearing based on closed HTS windings were obtained for temperatures ranging from 40 to 77.4 K and shift amplitudes of 1 to 9 mm. The numerical model was verified using experimental data. Its applicability was proven for closed superconducting currents in HTS tapes. The dynamics of magnetic flux penetration into HTS windings was calculated. CONCLUSION: Closed HTS windings can be successfully used to manufacture superconducting bearings. Closed HTS windings are most effective in systems where equilibrium shifts exceeding the half-period of the magnetic array are possible. The shift magnitude at which the greatest axial restoring force is achieved increases with temperature.
- 15 January 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (4)
Magneto-levitation characteristics of an HTS tapes stack at different cooling heights in a field of a permanent magnet
This paper presents the results of experimental and numerical studies of the levitation characteristics of a HTS suspension consisting of a composite HTS tapes stack based on the YBa 2 Cu 3 O 7-x compound and an array of cylindrical NdFeB permanent magnets. In particular, the magneto-force characteristics (rigidity and levitation force) of the system cooled by liquid nitrogen under field-cooling (FC) conditions have been considered. For different cooling heights, load characteristics have been obtainedfor both vertical and lateral displacements of the HTS element relative to the magnets, and the dynamics of changes in the rigidity of the levitation system have been considered. The key result of the study is the identification of a tendency towards a decrease in the maximum repulsive vertical force and a simultaneous increase in the maximum lateral restoring force as the cooling height of the HTS tapes stack decreases.
- 15 January 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (4)
Magneto-levitation characteristics of an HTS tapes stack at different cooling heights in a field of a permanent magnet
This paper presents the results of experimental and numerical studies of the levitation characteristics of a HTS suspension consisting of a composite HTS tapes stack based on the YBa 2 Cu 3 O 7-x compound and an array of cylindrical NdFeB permanent magnets. In particular, the magneto-force characteristics (rigidity and levitation force) of the system cooled by liquid nitrogen under field-cooling (FC) conditions have been considered. For different cooling heights, load characteristics have been obtainedfor both vertical and lateral displacements of the HTS element relative to the magnets, and the dynamics of changes in the rigidity of the levitation system have been considered. The key result of the study is the identification of a tendency towards a decrease in the maximum repulsive vertical force and a simultaneous increase in the maximum lateral restoring force as the cooling height of the HTS tapes stack decreases.
- Open Access
- 13 January 2026
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 39 (2)
Axial force analysis of superconducting bearings based on closed and non-closed windings of HTS tapes
Magnetic levitation systems, and in particular, superconducting bearings, are one of the possible practical applications of high-temperature superconductors. In recent years, windings from HTS tapes have been increasingly used as a material for manufacturing of superconducting bearings. Moreover, bearings can be made both on the basis of non-closed windings and closed windings, which are manufactured by making a central cut in the HTS tape. This paper presents the results of an experimental study of the load characteristics of radial bearings based on closed and non-closed HTS windings. The dependence of axial force on axial displacement in a wide range of temperatures, from 40 K to 77.4 K, has been investigated. Modeling of current distribution in a superconducting system using the finite element method and an analysis of the behavior of the axial force in the system have been carried out. The calculation results coincide with the experimental data with high accuracy. The results of measurements showed that the maximum axial force is higher for non-closed windings, but the differences become smaller as the temperature decreases. However, bearings based on closed HTS windings can be more advantageous in systems with low operating temperatures, in which large displacements from the equilibrium position are possible.
- 13 January 2026
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 39 (2)
Open AccessAxial force analysis of superconducting bearings based on closed and non-closed windings of HTS tapes
Magnetic levitation systems, and in particular, superconducting bearings, are one of the possible practical applications of high-temperature superconductors. In recent years, windings from HTS tapes have been increasingly used as a material for manufacturing of superconducting bearings. Moreover, bearings can be made both on the basis of non-closed windings and closed windings, which are manufactured by making a central cut in the HTS tape. This paper presents the results of an experimental study of the load characteristics of radial bearings based on closed and non-closed HTS windings. The dependence of axial force on axial displacement in a wide range of temperatures, from 40 K to 77.4 K, has been investigated. Modeling of current distribution in a superconducting system using the finite element method and an analysis of the behavior of the axial force in the system have been carried out. The calculation results coincide with the experimental data with high accuracy. The results of measurements showed that the maximum axial force is higher for non-closed windings, but the differences become smaller as the temperature decreases. However, bearings based on closed HTS windings can be more advantageous in systems with low operating temperatures, in which large displacements from the equilibrium position are possible.
- 1 November 2025
- Published by Kotelnikov Institute of Radioengineering and Electronics of Russian Academy of Sciences in Journal of Radio Electronics
- Vol. 2025 (11)
Influence of field cooling height on the levitation characteristics of an HTS tape stack
Contactless magnetic suspensions based on high-temperature superconductors (HTS) are of particular interest due to their ability to provide stable levitation without active control systems. One of the key factors affecting the performance of such systems is the field cooling height (FCH), which determines the distribution of the trapped magnetic flux and, consequently, the magnitude and stability of the levitation forces. The aim of this work is to experimentally and numerically investigate the effect of FCH on the vertical and lateral characteristics of a simple HTS suspension. The object of study is a basic configuration of an HTS suspension consisting of a stack of composite YBCO HTS tapes and a stack of cylindrical NdFeB permanent magnets. Experiments were carried out during cooling with liquid nitrogen for various FCH values in the range of 6–60 mm. Numerical simulations were performed using the finite element method in the A–T formulation with identical geometric parameters. Vertical and lateral load characteristics of the HTS suspension were obtained. It was found that the maximum vertical levitation force increases nonlinearly with FCH, while the maximum restoring force under lateral displacement decreases. A pronounced inverse correlation between these forces was observed. The identified dependencies reflect the balance between the load-bearing capacity and stability of the suspension, determined by the interaction of the superconductor with the non-uniform magnetic field. The obtained results can be used to optimize the parameters of HTS bearings, supports, and transport platforms, as well as to develop new methods for controlling their levitation characteristics.
- 1 November 2025
- Published by Kotelnikov Institute of Radioengineering and Electronics of Russian Academy of Sciences in Journal of Radio Electronics
- Vol. 2025 (11)
Influence of field cooling height on the levitation characteristics of an HTS tape stack
Contactless magnetic suspensions based on high-temperature superconductors (HTS) are of particular interest due to their ability to provide stable levitation without active control systems. One of the key factors affecting the performance of such systems is the field cooling height (FCH), which determines the distribution of the trapped magnetic flux and, consequently, the magnitude and stability of the levitation forces. The aim of this work is to experimentally and numerically investigate the effect of FCH on the vertical and lateral characteristics of a simple HTS suspension. The object of study is a basic configuration of an HTS suspension consisting of a stack of composite YBCO HTS tapes and a stack of cylindrical NdFeB permanent magnets. Experiments were carried out during cooling with liquid nitrogen for various FCH values in the range of 6–60 mm. Numerical simulations were performed using the finite element method in the A–T formulation with identical geometric parameters. Vertical and lateral load characteristics of the HTS suspension were obtained. It was found that the maximum vertical levitation force increases nonlinearly with FCH, while the maximum restoring force under lateral displacement decreases. A pronounced inverse correlation between these forces was observed. The identified dependencies reflect the balance between the load-bearing capacity and stability of the suspension, determined by the interaction of the superconductor with the non-uniform magnetic field. The obtained results can be used to optimize the parameters of HTS bearings, supports, and transport platforms, as well as to develop new methods for controlling their levitation characteristics.
- Open Access
- 30 September 2025
- Published by ECO-Vector LLC in Modern Transportation Systems and Technologies
- Vol. 11 (3) , 409-421
Determination of operating parameters of toroidal field coils of a tokamak based on a high-temperature superconductor
Aim: to determine the operating parameters of the toroidal magnetic field system (operating temperature, number of CORC cables, transport current value) of the MEPhIST-1 superconducting tokamak Materials and Methods: numerical calculation of the toroidal magnetic field of a tokamak was performed in the COMSOL Multiphysics software Results: magnetic field distributions were obtained for various values of the transport current flowing through the tokamak coil. The proportionality coefficients between the maximum magnetic field on the coil and the transport current, the operating magnetic field and the operating transport current were determined. Conclusion: the number of CORC cables required to achieve an operating magnetic field induction of 1 T has been determined: 7 at a temperature of 37.6 K and 6 at a temperature of 33.6 K. It has been shown that it is possible to achieve an operating field value of about 1.5T with 7 CORC cables when the temperature is lowered to 21.1 K.
- 30 September 2025
- Published by ECO-Vector LLC in Modern Transportation Systems and Technologies
- Vol. 11 (3) , 409-421
Open AccessDetermination of operating parameters of toroidal field coils of a tokamak based on a high-temperature superconductor
Aim: to determine the operating parameters of the toroidal magnetic field system (operating temperature, number of CORC cables, transport current value) of the MEPhIST-1 superconducting tokamak Materials and Methods: numerical calculation of the toroidal magnetic field of a tokamak was performed in the COMSOL Multiphysics software Results: magnetic field distributions were obtained for various values of the transport current flowing through the tokamak coil. The proportionality coefficients between the maximum magnetic field on the coil and the transport current, the operating magnetic field and the operating transport current were determined. Conclusion: the number of CORC cables required to achieve an operating magnetic field induction of 1 T has been determined: 7 at a temperature of 37.6 K and 6 at a temperature of 33.6 K. It has been shown that it is possible to achieve an operating field value of about 1.5T with 7 CORC cables when the temperature is lowered to 21.1 K.
- 27 January 2025
- Published by Krasnoyarsk State Agrarian University in Bulletin of KSAU
- No. 12
PREDICTING THE FATS MIGRATION RATE IN CHOCOLATES WITH PRALINE MASS FILLINGS
- 27 January 2025
- Published by Krasnoyarsk State Agrarian University in Bulletin of KSAU
- No. 12
PREDICTING THE FATS MIGRATION RATE IN CHOCOLATES WITH PRALINE MASS FILLINGS
- Open Access
- 17 October 2024
- Published by Elsevier in Superconductivity
- Vol. 12
Experimental and numerical study of radial and axial HTS magnetic couplers
- 17 October 2024
- Published by Elsevier in Superconductivity
- Vol. 12
Open AccessExperimental and numerical study of radial and axial HTS magnetic couplers
- 1 December 2023
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 86 (9) , 2020-2027
Peculiarities of Investigation of HTS Tape by Low-Temperature Magneto-Optical Visualization
In this paper, we analyze in detail the features of the application of the magneto-optical imaging technique for studying HTS tapes. We present a detailed description of the experimental technique and features of the research facility for low temperatures research. The features of the penetration of a magnetic field into a superconductor are described, and the procedure for calibrating a magneto-optical film and algorithms for calculating magnetic field profiles from magneto-optical images are described in detail.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Physics of Atomic Nuclei
- Vol. 86 (9) , 2020-2027
Peculiarities of Investigation of HTS Tape by Low-Temperature Magneto-Optical Visualization
In this paper, we analyze in detail the features of the application of the magneto-optical imaging technique for studying HTS tapes. We present a detailed description of the experimental technique and features of the research facility for low temperatures research. The features of the penetration of a magnetic field into a superconductor are described, and the procedure for calibrating a magneto-optical film and algorithms for calculating magnetic field profiles from magneto-optical images are described in detail.
- Open Access
- 24 December 2022
- Published by ECO-Vector LLC in Modern Transportation Systems and Technologies
- Vol. 8 (4) , 46-57
Influence of cooling conditions of HTS assembly on the characteristics of a moving maglev system
Background: analysis of the influence of cooling conditions of high-temperature superconducting elements on the power characteristics of a maglev system under conditions of rapidly changing magnetic fields Aim: analysis of the influence of cooling conditions of high-temperature superconducting elements on the force characteristics of a magnetic-levitation transport platform under conditions of rapidly changing magnetic fields caused by the inhomogeneity of the magnetic track. Methods: numerical analysis of the maglev system was performed by the finite element method in the Comsol Multiphysics engineering simulation software. Results: at fast, more than 5 T/s, magnetic field change rates, due to the motion of the superconductor in a magnetic field with a non-uniform local distribution, the preferred method of cooling is the use of cryocooler technology. At rates of change of the magnetic field less than 5 T/s, it is permissible to use liquid nitrogen as a cooler. Conclusion: The developed numerical model makes it possible to predict the dynamic characteristics of levitation systems of various scales and can be applied to contactless transport, as well as in rotating machines, including kinetic energy storage devices.
- 24 December 2022
- Published by ECO-Vector LLC in Modern Transportation Systems and Technologies
- Vol. 8 (4) , 46-57
Open AccessInfluence of cooling conditions of HTS assembly on the characteristics of a moving maglev system
Background: analysis of the influence of cooling conditions of high-temperature superconducting elements on the power characteristics of a maglev system under conditions of rapidly changing magnetic fields Aim: analysis of the influence of cooling conditions of high-temperature superconducting elements on the force characteristics of a magnetic-levitation transport platform under conditions of rapidly changing magnetic fields caused by the inhomogeneity of the magnetic track. Methods: numerical analysis of the maglev system was performed by the finite element method in the Comsol Multiphysics engineering simulation software. Results: at fast, more than 5 T/s, magnetic field change rates, due to the motion of the superconductor in a magnetic field with a non-uniform local distribution, the preferred method of cooling is the use of cryocooler technology. At rates of change of the magnetic field less than 5 T/s, it is permissible to use liquid nitrogen as a cooler. Conclusion: The developed numerical model makes it possible to predict the dynamic characteristics of levitation systems of various scales and can be applied to contactless transport, as well as in rotating machines, including kinetic energy storage devices.