Teck-Bin Arthur Lim
Research Subjects
Teck-Bin Arthur Lim has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Boon Siong Neo
Department of Chemical Engineering, Stanford University, Stanford, California 94305, USA
3 shared publications - Chang Wei Kang
Institute of High Performance Computing (IHPC) Agency for Science, Technology and Research (A*STAR), Singapore 138632, Singapore
3 shared publications - Ruiqin Shan3 shared publications
Shengwei Ma
3 shared publicationsChang-Wei Kang
2 shared publications- Do Xuan Vinh Nguyen2 shared publications
Latest Publications
- Open Access
- 15 April 2026
- Published by Elsevier in SSRN Electronic Journal
Computational Investigation of Partially Cracked Ammonia/Air Swirler Flames via Large- Eddy Simulation
Ammonia (NH3) is emerging as a promising carbon-free fuel in energy sector, yet its low reactivity and narrow flammability range pose challenges for achieving flame stability and efficient combustion applications. Adding hydrogen (H2) into NH3/air mixture can possibly enhance limitations in NH3/air flames. Despite recent progress, a comprehensive understanding of the coupled flow–chemistry interactions, emission pathways, and the evolution of key flame characteristics under varying operating conditions is still required for determining optimal gas-turbine operating regimes. This study employs computational fluid dynamics (CFD), using Large Eddy Simulation (LES) for turbulence modeling and the Eddy Dissipation Concept (EDC) for combustion, to investigate premixed NH3/H2/air combustion in a swirl-stabilized combustor and to identify conditions that promote stable and efficient operation. The simulation results are compared with experimental data for the key flame features to validate the numerical methodology. Detailed analyses of flame temperature, heat-release rate, and the spatial distributions of OH and NOx radicals are performed over a wide range of NH3 cracking ratios, equivalence ratios, and inlet flow rates to elucidate the coupled physicochemical and fluid-dynamic (turbulence) interactions governing the system. The combination of CFD simulation with LES and radial pathway analysis reveal distinct transitions in flame topology and stabilization mechanism associated with the central recirculation zone, as well as a competition between thermal efficiency and NOx formation pathways. Our numerical simulation results complement experimental findings as well as offer insights into strategies for improving combustion efficiency and mitigating the NOx emissions through parameter optimization.
- 15 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessComputational Investigation of Partially Cracked Ammonia/Air Swirler Flames via Large- Eddy Simulation
Ammonia (NH3) is emerging as a promising carbon-free fuel in energy sector, yet its low reactivity and narrow flammability range pose challenges for achieving flame stability and efficient combustion applications. Adding hydrogen (H2) into NH3/air mixture can possibly enhance limitations in NH3/air flames. Despite recent progress, a comprehensive understanding of the coupled flow–chemistry interactions, emission pathways, and the evolution of key flame characteristics under varying operating conditions is still required for determining optimal gas-turbine operating regimes. This study employs computational fluid dynamics (CFD), using Large Eddy Simulation (LES) for turbulence modeling and the Eddy Dissipation Concept (EDC) for combustion, to investigate premixed NH3/H2/air combustion in a swirl-stabilized combustor and to identify conditions that promote stable and efficient operation. The simulation results are compared with experimental data for the key flame features to validate the numerical methodology. Detailed analyses of flame temperature, heat-release rate, and the spatial distributions of OH and NOx radicals are performed over a wide range of NH3 cracking ratios, equivalence ratios, and inlet flow rates to elucidate the coupled physicochemical and fluid-dynamic (turbulence) interactions governing the system. The combination of CFD simulation with LES and radial pathway analysis reveal distinct transitions in flame topology and stabilization mechanism associated with the central recirculation zone, as well as a competition between thermal efficiency and NOx formation pathways. Our numerical simulation results complement experimental findings as well as offer insights into strategies for improving combustion efficiency and mitigating the NOx emissions through parameter optimization.
- 16 October 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 185
Numerical investigation of ammonia catalytic decomposition in a fixed-bed reactor
- 16 October 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 185
Numerical investigation of ammonia catalytic decomposition in a fixed-bed reactor
- 1 November 2018
- Published by Elsevier in Applied Ocean Research
- Vol. 80, 79-100
A new passive control technique for the suppression of vortex-induced motion in deep-draft semisubmersibles
- 1 November 2018
- Published by Elsevier in Applied Ocean Research
- Vol. 80, 79-100
A new passive control technique for the suppression of vortex-induced motion in deep-draft semisubmersibles
- 1 March 2017
- Published by AIP Publishing in Physics of Fluids
- Vol. 29 (3)
Wake of two side-by-side square cylinders at low Reynolds numbers
Wake of two side-by-side square cylinders was investigated through direct numerical simulation at low Reynolds numbers (16–200). The gap between the two cylinders varied from 0 to 10D, where D is the dimension of the square cylinder (edge length). 9 different wake patterns and their dependency on both the Reynolds number and gap spacing were identified and analysed. A system classification map, demarcated by the Reynolds number and gap ratio g* (g/D, where g is the gap spacing between 2 cylinders), was derived for these 9 wake modes. Steady-state wake (mode I) was observed when the Reynolds number is lower than the critical Reynolds number, which depends on g*. For the gap ratio less than 0.7, only single vortex street was observed. The single vortex street wake can be either symmetric and periodic (mode II), or asymmetric and periodic (mode III), or irregular (mode IV). In this gap ratio range (less than 0.7), shedding frequency decreases with the gap ratio due to the damping role of the gap flow. For the gap ratio larger than 0.7, two vortex streets were also observed. For the gap ratio larger than 1, only two vortex streets were observed. Vortex shedding can be either synchronized and in-phase (mode V), synchronized and anti-phase (mode VI), in-phase dominated with low frequency modulation (mode VII), anti-phase dominated with low frequency modulation (mode VIII), asymmetric synchronized anti-phase (mode IX), or irregular (mode IV). For the gap ratio larger than 4, only synchronized anti-phase mode was observed under the conditions of this study. In the two vortex streets regime, shedding frequency is higher than that of a single cylinder, due to a stronger gap flow than that in the freestream side. The impact of gap ratio and Reynolds number on the drag and lift forces was also studied.
- 1 March 2017
- Published by AIP Publishing in Physics of Fluids
- Vol. 29 (3)
Wake of two side-by-side square cylinders at low Reynolds numbers
Wake of two side-by-side square cylinders was investigated through direct numerical simulation at low Reynolds numbers (16–200). The gap between the two cylinders varied from 0 to 10D, where D is the dimension of the square cylinder (edge length). 9 different wake patterns and their dependency on both the Reynolds number and gap spacing were identified and analysed. A system classification map, demarcated by the Reynolds number and gap ratio g* (g/D, where g is the gap spacing between 2 cylinders), was derived for these 9 wake modes. Steady-state wake (mode I) was observed when the Reynolds number is lower than the critical Reynolds number, which depends on g*. For the gap ratio less than 0.7, only single vortex street was observed. The single vortex street wake can be either symmetric and periodic (mode II), or asymmetric and periodic (mode III), or irregular (mode IV). In this gap ratio range (less than 0.7), shedding frequency decreases with the gap ratio due to the damping role of the gap flow. For the gap ratio larger than 0.7, two vortex streets were also observed. For the gap ratio larger than 1, only two vortex streets were observed. Vortex shedding can be either synchronized and in-phase (mode V), synchronized and anti-phase (mode VI), in-phase dominated with low frequency modulation (mode VII), anti-phase dominated with low frequency modulation (mode VIII), asymmetric synchronized anti-phase (mode IX), or irregular (mode IV). For the gap ratio larger than 4, only synchronized anti-phase mode was observed under the conditions of this study. In the two vortex streets regime, shedding frequency is higher than that of a single cylinder, due to a stronger gap flow than that in the freestream side. The impact of gap ratio and Reynolds number on the drag and lift forces was also studied.
- Open Access
- 30 September 2014
- Published by Wiley in Journal of Fluids
- Vol. 2014, 1-7
Numerical Characterization of the Performance of Fluid Pumps Based on a Wankel Geometry
The performance of fluid pumps based on Wankel-type geometry, taking the shape of a double-lobed limaçon, is characterized. To the authors’ knowledge, this is the first time such an attempt has been made. To this end, numerous simulations for three different pump sizes were carried out and the results were understood in terms of the usual scaling coefficients. The results show that such pumps operate as low efficiency (<30%) valveless positive displacements pumps, with pump flow-rate noticeably falling at the onset of internal leakage. Also, for such pumps, the mechanical efficiency varies linearly with the head coefficient, and, within the onset of internal leakage, the capacity coefficient holds steady even across pump efficiency. Simulation of the flow field reveals a structure rich in three-dimensional vortices even in the laminar regime, including Taylor-like counterrotating vortex pairs, pointing towards the utility of these pumps in microfluidic applications. Given the planar geometry of such pumps, their applications as microreactors and micromixers are recommended.
- 30 September 2014
- Published by Wiley in Journal of Fluids
- Vol. 2014, 1-7
Open AccessNumerical Characterization of the Performance of Fluid Pumps Based on a Wankel Geometry
The performance of fluid pumps based on Wankel-type geometry, taking the shape of a double-lobed limaçon, is characterized. To the authors’ knowledge, this is the first time such an attempt has been made. To this end, numerous simulations for three different pump sizes were carried out and the results were understood in terms of the usual scaling coefficients. The results show that such pumps operate as low efficiency (<30%) valveless positive displacements pumps, with pump flow-rate noticeably falling at the onset of internal leakage. Also, for such pumps, the mechanical efficiency varies linearly with the head coefficient, and, within the onset of internal leakage, the capacity coefficient holds steady even across pump efficiency. Simulation of the flow field reveals a structure rich in three-dimensional vortices even in the laminar regime, including Taylor-like counterrotating vortex pairs, pointing towards the utility of these pumps in microfluidic applications. Given the planar geometry of such pumps, their applications as microreactors and micromixers are recommended.