Peijiang Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Peijiang Liu has a total of 129 co-authors. Here are the top co-authors by number of shared publications:
Zhengjun Yao
14 shared publicationsJintang Zhou
13 shared publications- Liguo Xu
College of Light Chemical Industry and Materials Engineering, Shunde Polytechnic, Foshan 528333, China
8 shared publications - Jintang Zhou
College of Materials Science and Technology Nanjing University of Aeronautics and Astronautics Nanjing China
7 shared publications - Zhenkai Huang
School of Materials and Energy, Foshan University, Foshan 528000, China
6 shared publications - Jianping Peng
School of Environment and Chemical Engineering, Foshan University, Foshan 528000, China
5 shared publications
Latest Publications
- Open Access
- 12 August 2026
- Published by Elsevier in SSRN Electronic Journal
In Situ Investigation of Failure Mechanisms in TGV Interconnect Structures Under Electrical Loading
With the trend towards high-frequency, high-power-density packaging, through-glass vias (TGV) are considered a promising alternative to TSVs. However, their reliability under high current density, a critical concern for practical application, remains insufficiently studied. This work systematically investigates the failure mechanisms of TGV interconnect structures under electrical loads. In-situ electromigration experiments were conducted on daisy-chain TGV samples at current densities of 2.3×105, 2.8×105, and 3.0×105 A/cm2, with real-time resistance monitoring and cross-sectional SEM analysis. Distinct failure modes were identified: at the lowest density, failure was dominated by RDL/glass interfacial delamination with negligible resistance change; at the medium density, electromigration became apparent, accelerating void nucleation/growth and causing a linear resistance increase; at the highest density, severe thermo-mechanical coupling led to glass cracking at the TGV-RDL corner and RDL plastic deformation, resulting in an accelerated resistance rise. Complementary electro-thermo-mechanical finite element simulations revealed significant current crowding at the TGV-RDL corners, with local current density exceeding that at the narrowest via cross-section. The combined temperature field and geometric features jointly determined the stress concentration locations. This study clarifies the failure mechanisms of TGV and provides insights for the reliable design of high-current-density glass interposer packages.
- 12 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIn Situ Investigation of Failure Mechanisms in TGV Interconnect Structures Under Electrical Loading
With the trend towards high-frequency, high-power-density packaging, through-glass vias (TGV) are considered a promising alternative to TSVs. However, their reliability under high current density, a critical concern for practical application, remains insufficiently studied. This work systematically investigates the failure mechanisms of TGV interconnect structures under electrical loads. In-situ electromigration experiments were conducted on daisy-chain TGV samples at current densities of 2.3×105, 2.8×105, and 3.0×105 A/cm2, with real-time resistance monitoring and cross-sectional SEM analysis. Distinct failure modes were identified: at the lowest density, failure was dominated by RDL/glass interfacial delamination with negligible resistance change; at the medium density, electromigration became apparent, accelerating void nucleation/growth and causing a linear resistance increase; at the highest density, severe thermo-mechanical coupling led to glass cracking at the TGV-RDL corner and RDL plastic deformation, resulting in an accelerated resistance rise. Complementary electro-thermo-mechanical finite element simulations revealed significant current crowding at the TGV-RDL corners, with local current density exceeding that at the narrowest via cross-section. The combined temperature field and geometric features jointly determined the stress concentration locations. This study clarifies the failure mechanisms of TGV and provides insights for the reliable design of high-current-density glass interposer packages.
- Open Access
- 9 April 2026
- Published by Elsevier in SSRN Electronic Journal
CsPbBr3/MXene ceramic phase interface-driven polarization loss for electromagnetic wave absorption
MXene is a research hotspot in electromagnetic wave absorption due to its excellent dielectric loss and controllable layered structure. However, the layered structure of MXene has an inherent tendency to stack and agglomerate, which, together with its high electrical conductivity, greatly limits the further enhancement of its electromagnetic wave absorption performance. In this study, the anti-solvent vapor-assisted crystallization method under mild vibration assistance is adopted to in-situ grow CsPbBr3 nanocrystals on the surface and between the layers of MXene. The introduction of CsPbBr3 not only effectively alleviates the agglomeration of MXene but also enhances the interfacial charge transfer effect and induces stronger interfacial polarization loss. This design significantly improves the impedance matching performance of MXene while optimizing its polarization attenuation efficiency. This research enriches the microcosmic regulatory mechanism of high-performance electromagnetic absorption materials and offers a new idea for designing novel, efficient MXene absorbers.
- 9 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCsPbBr3/MXene ceramic phase interface-driven polarization loss for electromagnetic wave absorption
MXene is a research hotspot in electromagnetic wave absorption due to its excellent dielectric loss and controllable layered structure. However, the layered structure of MXene has an inherent tendency to stack and agglomerate, which, together with its high electrical conductivity, greatly limits the further enhancement of its electromagnetic wave absorption performance. In this study, the anti-solvent vapor-assisted crystallization method under mild vibration assistance is adopted to in-situ grow CsPbBr3 nanocrystals on the surface and between the layers of MXene. The introduction of CsPbBr3 not only effectively alleviates the agglomeration of MXene but also enhances the interfacial charge transfer effect and induces stronger interfacial polarization loss. This design significantly improves the impedance matching performance of MXene while optimizing its polarization attenuation efficiency. This research enriches the microcosmic regulatory mechanism of high-performance electromagnetic absorption materials and offers a new idea for designing novel, efficient MXene absorbers.
- Open Access
Failure Behavior and Mechanism of Solder Joint Under Thermal Mechanical Coupling Loads
The periodic thermal loads to which electronic devices are exposed during operation induce alternating thermal stresses due to the mismatched coefficients of thermal expansion (CTE) between the solder joints and the surrounding materials. This leads to cyclic thermal strain, ultimately causing crack initiation, propagation, and failure of interconnect structures. This study investigates thermal fatigue failure of Sn3.5Ag solder joints induced by cyclic thermal stresses from CTE mismatch. Numerical simulations and experiments reveal that alternating shear strain concentrates at the joint–pad interface, serving as the crack initiation site. This study proposes a hypothesis: extracting the equivalent viscoplastic strain range from the steady-state hysteretic response after cyclic stabilization and applying it to the Coffin–Manson model can mitigate the strain overestimation inherent to methods based on the initial transient impact, thereby providing a more reasonable physical basis for thermal fatigue life evaluation. Based on this, the thermal fatigue life of the solder joint is predicted to be 18,930 cycles. Analysis confirms significantly higher viscoplastic strain energy density at this critical point, indicating energy dissipation drives damage. This study addresses the above hypothesis from three aspects: deformation mechanism, cyclic response, and energy dissipation, providing a key basis for developing a highly reliable method for assessing solder joint life.
Open AccessFailure Behavior and Mechanism of Solder Joint Under Thermal Mechanical Coupling Loads
The periodic thermal loads to which electronic devices are exposed during operation induce alternating thermal stresses due to the mismatched coefficients of thermal expansion (CTE) between the solder joints and the surrounding materials. This leads to cyclic thermal strain, ultimately causing crack initiation, propagation, and failure of interconnect structures. This study investigates thermal fatigue failure of Sn3.5Ag solder joints induced by cyclic thermal stresses from CTE mismatch. Numerical simulations and experiments reveal that alternating shear strain concentrates at the joint–pad interface, serving as the crack initiation site. This study proposes a hypothesis: extracting the equivalent viscoplastic strain range from the steady-state hysteretic response after cyclic stabilization and applying it to the Coffin–Manson model can mitigate the strain overestimation inherent to methods based on the initial transient impact, thereby providing a more reasonable physical basis for thermal fatigue life evaluation. Based on this, the thermal fatigue life of the solder joint is predicted to be 18,930 cycles. Analysis confirms significantly higher viscoplastic strain energy density at this critical point, indicating energy dissipation drives damage. This study addresses the above hypothesis from three aspects: deformation mechanism, cyclic response, and energy dissipation, providing a key basis for developing a highly reliable method for assessing solder joint life.
- 4 December 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 61  (1) , 375-392
Mechanical, dielectric, thermal evolution, and aging mechanism of liquid crystal polymer films for 5G communication applications under humidity and heat conditions
- 4 December 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 61  (1) , 375-392
Mechanical, dielectric, thermal evolution, and aging mechanism of liquid crystal polymer films for 5G communication applications under humidity and heat conditions
- Open Access
One-Pot Synthesis of Mechanically Robust Eutectogels via Carboxyl-Al(III) Coordination for Reliable Flexible Strain Sensor
This work presents a facile one-pot synthesis strategy for highly strong and tough eutectogels. The exceptional mechanical performance (average stress: 3.8 MPa; average strain: 920%) stems from synergistic trivalent aluminum(III)–ligand coordination crosslinking and extensive hydrogen bonding within the network. The optimized proportion has achieved a balance between mechanical stress and strain. Reversible bonding enables rapid energy dissipation and elastic recovery. A flexible strain sensor fabricated from this eutectogel demonstrates high sensitivity (gauge factor > 2) and ultrafast response (200 ms), validating its potential as low-cost electronic skin. This research provides a foundational framework for developing sustainable, high-performance flexible.
Open AccessOne-Pot Synthesis of Mechanically Robust Eutectogels via Carboxyl-Al(III) Coordination for Reliable Flexible Strain Sensor
This work presents a facile one-pot synthesis strategy for highly strong and tough eutectogels. The exceptional mechanical performance (average stress: 3.8 MPa; average strain: 920%) stems from synergistic trivalent aluminum(III)–ligand coordination crosslinking and extensive hydrogen bonding within the network. The optimized proportion has achieved a balance between mechanical stress and strain. Reversible bonding enables rapid energy dissipation and elastic recovery. A flexible strain sensor fabricated from this eutectogel demonstrates high sensitivity (gauge factor > 2) and ultrafast response (200 ms), validating its potential as low-cost electronic skin. This research provides a foundational framework for developing sustainable, high-performance flexible.
- Open Access
- 18 August 2025
- Published by Springer Nature in Research Square
Time and temperature dependence of residual stress evolution and protrusion behavior in through-glass vias
Through glass via (TGV) has emerged as a critical solution for next-generation packaging platforms owing to its low dielectric loss, superior coefficient of thermal expansion (CTE) compatibility. Previous studies shows that low thermal conductivity of TGV could lead to thermo-mechanical failures. However, current research on failure behavior of TGV induced by thermal stress structures remains relatively limited. This paper investigates the effects of annealing conditions on residual stress distribution and Cu protrusion behavior in TGV. The evolution of residual stress in glass substrates under different annealing temperatures and annealing periods was analyzed by nanoindentation, and the corresponding morphological changes of Cu protrusions were characterized by atomic force microscopy (AFM). It is found that annealing helps reduce residual stress on the glass substrate, but prolonged annealing can lead to the generation of residual tensile stress, thereby causing glass cracking; Cu protrusion height increases with annealing period but shows a decreasing growth rate. A creep rate model is established, achieving 87.32% prediction accuracy for TGV creep behavior. These results provide theoretical guidance for TGV reliability assessment and thermal optimization design.
- 18 August 2025
- Published by Springer Nature in Research Square
Open AccessTime and temperature dependence of residual stress evolution and protrusion behavior in through-glass vias
Through glass via (TGV) has emerged as a critical solution for next-generation packaging platforms owing to its low dielectric loss, superior coefficient of thermal expansion (CTE) compatibility. Previous studies shows that low thermal conductivity of TGV could lead to thermo-mechanical failures. However, current research on failure behavior of TGV induced by thermal stress structures remains relatively limited. This paper investigates the effects of annealing conditions on residual stress distribution and Cu protrusion behavior in TGV. The evolution of residual stress in glass substrates under different annealing temperatures and annealing periods was analyzed by nanoindentation, and the corresponding morphological changes of Cu protrusions were characterized by atomic force microscopy (AFM). It is found that annealing helps reduce residual stress on the glass substrate, but prolonged annealing can lead to the generation of residual tensile stress, thereby causing glass cracking; Cu protrusion height increases with annealing period but shows a decreasing growth rate. A creep rate model is established, achieving 87.32% prediction accuracy for TGV creep behavior. These results provide theoretical guidance for TGV reliability assessment and thermal optimization design.
- Open Access
- 1 August 2025
- Published by KEAI Publishing in Advanced Powder Materials
- Vol. 4  (4)
Enhancing dipole polarization loss in conjugated metal-organic frameworks via coordination symmetry breaking under electromagnetic field
- 1 August 2025
- Published by KEAI Publishing in Advanced Powder Materials
- Vol. 4  (4)
Open AccessEnhancing dipole polarization loss in conjugated metal-organic frameworks via coordination symmetry breaking under electromagnetic field
- 11 July 2025
- Published by Royal Society of Chemistry (RSC) in Materials Chemistry Frontiers
- Vol. 9  (17) , 2611-2622
Double-layer absorbers based on Co0.2Ni0.4Zn0.4Fe2O4 and Ti3C2Tx composites for microwave absorption through optimal combination
Double-layer absorbers serve the purpose of achieving high transmission efficiency and attenuation intensity in real-life applications. MXene-based composites exhibit huge potential in absorbing electromagnetic (EM) waves. In this work, Co0.2Ni0.4Zn0.4Fe2O4 (CNZF) ferrites and Ti3C2Tx/Co0.2Ni0.4Zn0.4Fe2O4 (Ti3C2Tx/CNZF) composites were fabricated via a hydrothermal method. XRD, FT-IR, XPS, SEM, and TEM were employed to analyze the composition and morphology of the samples. Specifically, microwave absorption properties of the single-layer and double-layer absorbers composed of CNZF and Ti3C2Tx/CNZF at varying thicknesses, were studied. For the double-layer absorber with CNZF as the matching layer (0.4 mm) and Ti3C2Tx/CNZF as the absorbing layer (2.4 mm), the maximum reflection loss (RL) reached −44.4 dB at 7.6 GHz. This represented an exceptionally strong absorption performance at a relatively low frequency with a remarkably thin total absorber thickness of only 2.8 mm, overcoming the typical limitations of achieving high absorption at lower frequencies which often require thicker absorbers. The optimized double-layer structure demonstrates a practical solution for developing lightweight, thin, and high-performance microwave absorbers. The improved microwave absorption performance can be attributed to enhanced interfacial polarization, multiple reflections and scattering, as well as the rational layer configuration. These findings suggest that Ti3C2Tx/CNZF-based double-layer absorbers are promising candidates for achieving high-performance, thin microwave-absorbing materials.
- 11 July 2025
- Published by Royal Society of Chemistry (RSC) in Materials Chemistry Frontiers
- Vol. 9  (17) , 2611-2622
Double-layer absorbers based on Co0.2Ni0.4Zn0.4Fe2O4 and Ti3C2Tx composites for microwave absorption through optimal combination
Double-layer absorbers serve the purpose of achieving high transmission efficiency and attenuation intensity in real-life applications. MXene-based composites exhibit huge potential in absorbing electromagnetic (EM) waves. In this work, Co0.2Ni0.4Zn0.4Fe2O4 (CNZF) ferrites and Ti3C2Tx/Co0.2Ni0.4Zn0.4Fe2O4 (Ti3C2Tx/CNZF) composites were fabricated via a hydrothermal method. XRD, FT-IR, XPS, SEM, and TEM were employed to analyze the composition and morphology of the samples. Specifically, microwave absorption properties of the single-layer and double-layer absorbers composed of CNZF and Ti3C2Tx/CNZF at varying thicknesses, were studied. For the double-layer absorber with CNZF as the matching layer (0.4 mm) and Ti3C2Tx/CNZF as the absorbing layer (2.4 mm), the maximum reflection loss (RL) reached −44.4 dB at 7.6 GHz. This represented an exceptionally strong absorption performance at a relatively low frequency with a remarkably thin total absorber thickness of only 2.8 mm, overcoming the typical limitations of achieving high absorption at lower frequencies which often require thicker absorbers. The optimized double-layer structure demonstrates a practical solution for developing lightweight, thin, and high-performance microwave absorbers. The improved microwave absorption performance can be attributed to enhanced interfacial polarization, multiple reflections and scattering, as well as the rational layer configuration. These findings suggest that Ti3C2Tx/CNZF-based double-layer absorbers are promising candidates for achieving high-performance, thin microwave-absorbing materials.