Mahdi Khishvand
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mahdi Khishvand has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Mohammad Piri
Center of Innovation for Flow through Porous Media, Department of Energy and Petroleum Engineering, University of Wyoming , Laramie, Wyoming 82071, USA
4 shared publications- Mohammad Piri
University of Wyoming
3 shared publications - Amir H. Alizadeh
Department of Petroleum Engineering University of Wyoming Laramie Wyoming USA
2 shared publications - Haolin Qu
Center of Innovation for Flow through Porous Media, Department of Energy and Petroleum Engineering
2 shared publications - Uche Igwe
Center of Innovation for Flow through Porous Media, Department of Energy and Petroleum Engineering, University of Wyoming , Laramie, Wyoming 82071, USA
2 shared publications A. A. Sheikhloo
Research Institute of Petroleum Industry (RIPI), Tehran, Iran
1 shared publication
Latest Publications
- 23 October 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (44) , 24187-24200
Evolution of In Situ Wettability and Capillary Displacements in Carbonate Rocks: The Effect of Injection Brine Composition
Ion-specific interactions at fluid-mineral interfaces play a critical role in controlling wettability and multiphase flow in porous materials. In this study, a series of two-phase flow experiments were conducted on miniature oil-wet carbonate cores to investigate how aqueous chemistry regulates dynamic wettability evolution and pore-scale displacement behavior. Companion cores were conditioned using a common aging protocol to establish comparable mean oil-wet states and subsequently subjected to waterflooding under controlled chemical environments. Fluid configurations and in situ geometric contact angles were characterized at successive imaging stages using high-resolution X-ray microcomputed tomography. As wettability evolved in response to controlled aqueous chemistry toward less oil-wet states, the pathways of pore-scale invasion were correspondingly reorganized. Morphology-based analysis of the oil displaced between consecutive imaging stages quantified the relative volume contributions of piston-like invasion and wetting-layer drainage to incremental oil recovery. Piston-like invasion dominated initial displacement, whereas wetting-layer drainage accounted for most later-stage recovery during low-salinity flooding. These stage-dependent contributions connect brine-associated wettability changes with the pore-scale processes responsible for oil mobilization.
- 23 October 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (44) , 24187-24200
Evolution of In Situ Wettability and Capillary Displacements in Carbonate Rocks: The Effect of Injection Brine Composition
Ion-specific interactions at fluid-mineral interfaces play a critical role in controlling wettability and multiphase flow in porous materials. In this study, a series of two-phase flow experiments were conducted on miniature oil-wet carbonate cores to investigate how aqueous chemistry regulates dynamic wettability evolution and pore-scale displacement behavior. Companion cores were conditioned using a common aging protocol to establish comparable mean oil-wet states and subsequently subjected to waterflooding under controlled chemical environments. Fluid configurations and in situ geometric contact angles were characterized at successive imaging stages using high-resolution X-ray microcomputed tomography. As wettability evolved in response to controlled aqueous chemistry toward less oil-wet states, the pathways of pore-scale invasion were correspondingly reorganized. Morphology-based analysis of the oil displaced between consecutive imaging stages quantified the relative volume contributions of piston-like invasion and wetting-layer drainage to incremental oil recovery. Piston-like invasion dominated initial displacement, whereas wetting-layer drainage accounted for most later-stage recovery during low-salinity flooding. These stage-dependent contributions connect brine-associated wettability changes with the pore-scale processes responsible for oil mobilization.
- 3 November 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (45) , 30644-30662
Pore-Scale Displacement Dynamics of Oil Recovery during Viscoelastic Fluid Injection in Oil-Wet Carbonates
Heavy oil recovery from oil-wet carbonate reservoirs remains a major challenge due to the high oil viscosity, unfavorable mobility ratio, and poor sweep efficiency in such systems. Understanding oil production under various enhanced oil recovery (EOR) mechanisms and predictive modeling/simulation in these reservoirs has also been particularly difficult due to the limited knowledge of the governing pore-scale displacement processes. This gap in understanding becomes even more evident for viscoelastic fluids. Hence, this study is designed to probe these pore-scale subtleties while injecting viscoelastic polymer and surfactant-polymer (SP) solutions. To this end, a series of multistage waterflooding, polymer flooding, and SP flooding tests were conducted across both capillary-dominated and viscous-dominated flow regimes under reservoir-representative conditions and on oil-wet miniature Prairie Shell carbonate rock samples. The flow tests were performed using a core-flooding apparatus integrated with a high-resolution X-ray imaging system to acquire three-dimensional pore-scale fluid distribution maps. These data were analyzed to characterize in situ wettability, quantify fluid saturations, and evaluate sweep efficiencies and displacement mechanisms. The results showed that the waterfloods recovered only 51-54% of the initial oil in place under capillary-dominated conditions and 67-68% under viscous-dominated conditions. In contrast, polymer and SP flooding increased recovery factors to, respectively, 61 and 69% under the capillary-dominated flow regime and 91 and 93% under the viscous-dominated flow regime. Pore-scale data analysis revealed that oil production occurred primarily through interface movement and piston-like displacements. The polymer and SP solutions have also mobilized wetting oil layers on pore walls and in the corners through viscoelastic pulling effects, which were not observed during the waterfloods. Moreover, the SP flooding outperformed polymer flooding at low injection rates since the surfactant solution lowered the oil-brine interfacial tension, reduced the entry capillary pressures, and emulsified some of the trapped oil clusters into smaller globules. Both polymer and SP solutions yielded comparable recoveries at higher flow rates as globule mobilization and ganglion dynamics dominated the displacement processes in both cases. These findings were further validated through pore-by-pore analysis of fluid occupancies.
- 3 November 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (45) , 30644-30662
Pore-Scale Displacement Dynamics of Oil Recovery during Viscoelastic Fluid Injection in Oil-Wet Carbonates
Heavy oil recovery from oil-wet carbonate reservoirs remains a major challenge due to the high oil viscosity, unfavorable mobility ratio, and poor sweep efficiency in such systems. Understanding oil production under various enhanced oil recovery (EOR) mechanisms and predictive modeling/simulation in these reservoirs has also been particularly difficult due to the limited knowledge of the governing pore-scale displacement processes. This gap in understanding becomes even more evident for viscoelastic fluids. Hence, this study is designed to probe these pore-scale subtleties while injecting viscoelastic polymer and surfactant-polymer (SP) solutions. To this end, a series of multistage waterflooding, polymer flooding, and SP flooding tests were conducted across both capillary-dominated and viscous-dominated flow regimes under reservoir-representative conditions and on oil-wet miniature Prairie Shell carbonate rock samples. The flow tests were performed using a core-flooding apparatus integrated with a high-resolution X-ray imaging system to acquire three-dimensional pore-scale fluid distribution maps. These data were analyzed to characterize in situ wettability, quantify fluid saturations, and evaluate sweep efficiencies and displacement mechanisms. The results showed that the waterfloods recovered only 51-54% of the initial oil in place under capillary-dominated conditions and 67-68% under viscous-dominated conditions. In contrast, polymer and SP flooding increased recovery factors to, respectively, 61 and 69% under the capillary-dominated flow regime and 91 and 93% under the viscous-dominated flow regime. Pore-scale data analysis revealed that oil production occurred primarily through interface movement and piston-like displacements. The polymer and SP solutions have also mobilized wetting oil layers on pore walls and in the corners through viscoelastic pulling effects, which were not observed during the waterfloods. Moreover, the SP flooding outperformed polymer flooding at low injection rates since the surfactant solution lowered the oil-brine interfacial tension, reduced the entry capillary pressures, and emulsified some of the trapped oil clusters into smaller globules. Both polymer and SP solutions yielded comparable recoveries at higher flow rates as globule mobilization and ganglion dynamics dominated the displacement processes in both cases. These findings were further validated through pore-by-pore analysis of fluid occupancies.
- Open Access
- 1 October 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (10)
The effects of initial water saturation on retrograde condensation in natural porous media: An in situ experimental investigation of three-phase displacements
In this study, state-of-the-art imaging technology is integrated with a miniature core-flooding system to map pore-scale fluid occupancy during the retrograde condensation process in the presence of brine and in a natural porous medium. Two depletion experiments were performed using a three-component synthetic gas condensate mixture in a Fontainebleau sandstone core sample and after establishing different levels of initial water saturations. The results are analyzed to investigate the impact of water saturation on condensate formation, accumulation, and mobilization and to shed light on the relevant three-phase flow dynamics. The results provide the first direct pore-scale observation of gas, condensate, and brine residing in the pore space. The micro-scale fluid occupancy maps illustrated that the presence of water in the pores delays the pressure at which condensate nuclei form, slows down the initial growth of nuclei, and partially impedes the accumulation of condensate. The higher the water saturation is, the lower the amount of condensate will be accumulated. As the pore pressure decreases, the condensate clusters develop significantly in the pore space triggering chains of displacement events between various pairs of fluids. The key mechanisms include gas-to-brine/condensate and condensate-to-gas/brine. The displacement events eventually reduce the brine saturation and increase the gas and condensate saturations in the pore space. The condensate saturation increases monotonically as the pore pressure reduces and reaches a maximum value. Quantitative pore fluid occupancy data also reconfirm the visual observations and demonstrate that condensate accumulation is associated with displacing gas and brine from small- and medium-sized pore elements.
- 1 October 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (10)
Open AccessThe effects of initial water saturation on retrograde condensation in natural porous media: An in situ experimental investigation of three-phase displacements
In this study, state-of-the-art imaging technology is integrated with a miniature core-flooding system to map pore-scale fluid occupancy during the retrograde condensation process in the presence of brine and in a natural porous medium. Two depletion experiments were performed using a three-component synthetic gas condensate mixture in a Fontainebleau sandstone core sample and after establishing different levels of initial water saturations. The results are analyzed to investigate the impact of water saturation on condensate formation, accumulation, and mobilization and to shed light on the relevant three-phase flow dynamics. The results provide the first direct pore-scale observation of gas, condensate, and brine residing in the pore space. The micro-scale fluid occupancy maps illustrated that the presence of water in the pores delays the pressure at which condensate nuclei form, slows down the initial growth of nuclei, and partially impedes the accumulation of condensate. The higher the water saturation is, the lower the amount of condensate will be accumulated. As the pore pressure decreases, the condensate clusters develop significantly in the pore space triggering chains of displacement events between various pairs of fluids. The key mechanisms include gas-to-brine/condensate and condensate-to-gas/brine. The displacement events eventually reduce the brine saturation and increase the gas and condensate saturations in the pore space. The condensate saturation increases monotonically as the pore pressure reduces and reaches a maximum value. Quantitative pore fluid occupancy data also reconfirm the visual observations and demonstrate that condensate accumulation is associated with displacing gas and brine from small- and medium-sized pore elements.
- 1 April 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (4)
Entrapment and mobilization dynamics during the flow of viscoelastic fluids in natural porous media: A micro-scale experimental investigation
Capillary desaturation process was investigated as a function of wetting phase rheological signatures during the injection of Newtonian and non-Newtonian fluids. Two sets of two-phase imbibition flow experiments were conducted on a water-wet sandstone core sample using brine and viscoelastic polymer solutions. During the experiments, a high-resolution micro-computed tomography scanner was employed to directly map pore-level fluid occupancies within the pore space. The results of the experiments revealed that at a given capillary number, the viscoelastic polymer was more efficient than the brine in recovering the non-wetting oil phase. At low capillary numbers, this is attributed to the improved accessibility of the viscoelastic polymer solution to the entrance of pore elements, which suppressed snap-off events and allowed more piston-like and cooperative pore-body filling events to contribute to oil displacement. For intermediate capillary numbers, the onset of elastic turbulence caused substantial desaturation, while at high capillary numbers, the superimposed effects of higher viscous and elastic forces further improved the mobilization of the trapped oil ganglia by the viscoelastic polymer. In the waterflood, however, the mobilization of oil globules was the governing recovery mechanism, and the desaturation process commenced only when the capillary number reached a threshold value. These observations were corroborated with the pore-level fluid occupancy maps produced for the brine and viscoelastic polymer solutions during the experiments. Furthermore, at the intermediate and high capillary numbers, the force balance and pore-fluid occupancies suggested different flow regimes for the non-Newtonian viscoelastic polymer. These regions are categorized in this study as elastic-capillary- and viscoelastic-dominated flow regimes, different from viscous-capillary flow conditions that are dominant during the flow of Newtonian fluids. Moreover, we have identified novel previously unreported pore-scale displacement events that take place during the flow of viscoelastic fluids in a natural heterogeneous porous medium. These events, including coalescence, fragmentation, and re-entrapment of oil ganglia, occurred before the threshold of oil mobilization was reached under the elastic-capillary-dominated flow regime. In addition, we present evidence for lubrication effects at the pore level due to the elastic properties of the polymer solution. Furthermore, a comparison of capillary desaturation curves generated for the Newtonian brine and non-Newtonian viscoelastic polymer revealed that the desaturation process was more significant for the viscoelastic polymer than for the brine. Finally, the analysis of trapped oil clusters showed that the ganglion size distribution depends on both the capillary number and the rheological properties of fluids.
- 1 April 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (4)
Entrapment and mobilization dynamics during the flow of viscoelastic fluids in natural porous media: A micro-scale experimental investigation
Capillary desaturation process was investigated as a function of wetting phase rheological signatures during the injection of Newtonian and non-Newtonian fluids. Two sets of two-phase imbibition flow experiments were conducted on a water-wet sandstone core sample using brine and viscoelastic polymer solutions. During the experiments, a high-resolution micro-computed tomography scanner was employed to directly map pore-level fluid occupancies within the pore space. The results of the experiments revealed that at a given capillary number, the viscoelastic polymer was more efficient than the brine in recovering the non-wetting oil phase. At low capillary numbers, this is attributed to the improved accessibility of the viscoelastic polymer solution to the entrance of pore elements, which suppressed snap-off events and allowed more piston-like and cooperative pore-body filling events to contribute to oil displacement. For intermediate capillary numbers, the onset of elastic turbulence caused substantial desaturation, while at high capillary numbers, the superimposed effects of higher viscous and elastic forces further improved the mobilization of the trapped oil ganglia by the viscoelastic polymer. In the waterflood, however, the mobilization of oil globules was the governing recovery mechanism, and the desaturation process commenced only when the capillary number reached a threshold value. These observations were corroborated with the pore-level fluid occupancy maps produced for the brine and viscoelastic polymer solutions during the experiments. Furthermore, at the intermediate and high capillary numbers, the force balance and pore-fluid occupancies suggested different flow regimes for the non-Newtonian viscoelastic polymer. These regions are categorized in this study as elastic-capillary- and viscoelastic-dominated flow regimes, different from viscous-capillary flow conditions that are dominant during the flow of Newtonian fluids. Moreover, we have identified novel previously unreported pore-scale displacement events that take place during the flow of viscoelastic fluids in a natural heterogeneous porous medium. These events, including coalescence, fragmentation, and re-entrapment of oil ganglia, occurred before the threshold of oil mobilization was reached under the elastic-capillary-dominated flow regime. In addition, we present evidence for lubrication effects at the pore level due to the elastic properties of the polymer solution. Furthermore, a comparison of capillary desaturation curves generated for the Newtonian brine and non-Newtonian viscoelastic polymer revealed that the desaturation process was more significant for the viscoelastic polymer than for the brine. Finally, the analysis of trapped oil clusters showed that the ganglion size distribution depends on both the capillary number and the rheological properties of fluids.
- 13 March 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (11) , 3837-3852
Synergistic Effects of Aqueous Phase Viscoelasticity and Reduced Interfacial Tension on Nonwetting Phase Displacement Efficiency: An In Situ Experimental Investigation
This study uses in situ experimental investigation techniques to probe the synergistic effects of aqueous phase viscoelasticity and reduced interfacial tension on nonwetting phase displacement efficiency in natural porous media. Specifically, it examines the efficacy of viscoelastic surfactant (VES) solutions in enhancing oil recovery and investigates the pore-scale displacement mechanisms and VES-oil interactions. To this end, we first performed an extensive rheological characterization to select two VES solutions from multiple CTAB/NaNO3 (CTN) and Cocobetaine/SDS/ NaCl (CSN) mixtures. The selected aqueous solutions were then used in unsteady-state imbibition experiments conducted on miniature, water-wet Prairie Shell carbonate core samples. The experiments were performed utilizing a high-pressure, high-temperature two-phase core-flooding apparatus integrated with a high-resolution X-ray imaging system to acquire pore-scale fluid occupancy maps during the displacements. The results indicate that the injection of the selected CSN and CTN solutions into the carbonate samples under capillary-dominated flow regimes boosts the oil recovery by 12 and 2%, respectively, compared to those of the base waterflood. The VES solutions lowered the oil-water interfacial tension and exerted significant shear forces at the entrance of pores. The shear forces could exceed the threshold surface free energy required to deform oil globules, and consequently, large oil clusters were fragmented into smaller blobs and eventually produced from the pore space. The higher oil recovery by CSN flooding was attributed to its stronger viscoelastic properties. The VES injection under the viscous-dominated flow regime intensified the frequency of oil globule fragmentation. As a result, residual oil saturation values were sharply reduced in the rock samples from 44 to 55% during the capillary-dominated flows to approximately 8%. The above-mentioned observations were also verified using morphological analysis of residual oil clusters. The impacts of VES flooding on the pore-scale oil configuration and the fragmentation of large oil clusters were particularly evident at higher VES flow rates.
- 13 March 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (11) , 3837-3852
Synergistic Effects of Aqueous Phase Viscoelasticity and Reduced Interfacial Tension on Nonwetting Phase Displacement Efficiency: An In Situ Experimental Investigation
This study uses in situ experimental investigation techniques to probe the synergistic effects of aqueous phase viscoelasticity and reduced interfacial tension on nonwetting phase displacement efficiency in natural porous media. Specifically, it examines the efficacy of viscoelastic surfactant (VES) solutions in enhancing oil recovery and investigates the pore-scale displacement mechanisms and VES-oil interactions. To this end, we first performed an extensive rheological characterization to select two VES solutions from multiple CTAB/NaNO3 (CTN) and Cocobetaine/SDS/ NaCl (CSN) mixtures. The selected aqueous solutions were then used in unsteady-state imbibition experiments conducted on miniature, water-wet Prairie Shell carbonate core samples. The experiments were performed utilizing a high-pressure, high-temperature two-phase core-flooding apparatus integrated with a high-resolution X-ray imaging system to acquire pore-scale fluid occupancy maps during the displacements. The results indicate that the injection of the selected CSN and CTN solutions into the carbonate samples under capillary-dominated flow regimes boosts the oil recovery by 12 and 2%, respectively, compared to those of the base waterflood. The VES solutions lowered the oil-water interfacial tension and exerted significant shear forces at the entrance of pores. The shear forces could exceed the threshold surface free energy required to deform oil globules, and consequently, large oil clusters were fragmented into smaller blobs and eventually produced from the pore space. The higher oil recovery by CSN flooding was attributed to its stronger viscoelastic properties. The VES injection under the viscous-dominated flow regime intensified the frequency of oil globule fragmentation. As a result, residual oil saturation values were sharply reduced in the rock samples from 44 to 55% during the capillary-dominated flows to approximately 8%. The above-mentioned observations were also verified using morphological analysis of residual oil clusters. The impacts of VES flooding on the pore-scale oil configuration and the fragmentation of large oil clusters were particularly evident at higher VES flow rates.
- 1 January 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (1) , 013102
Retrograde condensation in natural porous media: An in situ experimental investigation
Complex in situ behavior of fluids during a retrograde condensation process is experimentally investigated in a miniature sandstone core sample. Two depletion experiments were conducted with various pressure decline rates using a three-component synthetic gas mixture with a dew point of 3610 psi. A state-of-the-art miniature core-flooding system integrated with a high-resolution micro-computed tomography scanner was employed to acquire pore-scale evidence of condensate nucleation, growth, accumulation, and mobilization in a natural porous medium under different depletion conditions. Analysis of pore-scale fluid occupancy maps demonstrates the formation of discrete nuclei of the condensate in pore throats and crevices as the pressure drops slightly below the dew point. The in situ fluid configurations show that a greater pressure drawdown rate significantly increases the condensate growth and accumulation. The results also illustrate the occurrence of condensate-to-gas imbibition displacements, i.e., snap-off and piston-like events, and the consequent trapping of the gas phase in the pore space. As the pore pressure is reduced, the condensate droplets are found to connect to each other through wetting layers, whereas the large gas clusters are continuously fragmented into smaller globules with reduced hydraulic connectivities. This effect was more pronounced in the case of the high depletion rate experiment. Furthermore, the condensate banking was not completely eliminated (through evaporation) by re-injecting the gas phase. This implies that in the development of a gas condensate reservoir, condensate dropout and banking should be minimized in the first place by, for instance, producing at lower pressure drawdown rates.
- 1 January 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (1) , 013102
Retrograde condensation in natural porous media: An in situ experimental investigation
Complex in situ behavior of fluids during a retrograde condensation process is experimentally investigated in a miniature sandstone core sample. Two depletion experiments were conducted with various pressure decline rates using a three-component synthetic gas mixture with a dew point of 3610 psi. A state-of-the-art miniature core-flooding system integrated with a high-resolution micro-computed tomography scanner was employed to acquire pore-scale evidence of condensate nucleation, growth, accumulation, and mobilization in a natural porous medium under different depletion conditions. Analysis of pore-scale fluid occupancy maps demonstrates the formation of discrete nuclei of the condensate in pore throats and crevices as the pressure drops slightly below the dew point. The in situ fluid configurations show that a greater pressure drawdown rate significantly increases the condensate growth and accumulation. The results also illustrate the occurrence of condensate-to-gas imbibition displacements, i.e., snap-off and piston-like events, and the consequent trapping of the gas phase in the pore space. As the pore pressure is reduced, the condensate droplets are found to connect to each other through wetting layers, whereas the large gas clusters are continuously fragmented into smaller globules with reduced hydraulic connectivities. This effect was more pronounced in the case of the high depletion rate experiment. Furthermore, the condensate banking was not completely eliminated (through evaporation) by re-injecting the gas phase. This implies that in the development of a gas condensate reservoir, condensate dropout and banking should be minimized in the first place by, for instance, producing at lower pressure drawdown rates.
- Open Access
- 17 May 2017
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 53 (5) , 4427-4443
In situ characterization of wettability alteration and displacement mechanisms governing recovery enhancement due to low‐salinity waterflooding
A series of micro‐scale core‐flooding experiments were performed on reservoir core samples at elevated temperature and pressure conditions to develop better insights into wettability alteration and pore‐scale displacement mechanisms taking place during low‐salinity waterflooding (LSWF). Two individual miniature core samples were cut from a preserved reservoir whole core, saturated to establish initial reservoir fluid saturation conditions, and subsequently waterflooded with low‐salinity and high‐salinity brines. A third miniature sister core sample was also cut, solvent‐cleaned, and subjected to a dynamic wettability restoration process (to reestablish native state wettability) and then a low‐salinity waterflood. All samples were imaged during the experiments using a micro‐CT scanner to obtain fluid occupancy maps and measure in situ oil‐water contact angles. The results of the experiments performed on the preserved core samples show a significantly improved performance of low‐salinity waterflooding compared to that of high‐salinity waterflooding (HSWF). Pore‐scale contact angle measurements provide direct evidence of wettability alteration from weakly oil‐wet toward weakly water‐wet conditions during LSWF, whereas contact angles measured during HSWF remain unchanged. We believe that the reduction in oil‐water contact angles toward increased water‐wetness lowers the threshold water pressure needed to displace oil from some medium‐sized pore elements. Contact angles measured during the dynamic wettability restoration process show an equilibrium wettability state very similar to the initial one observed in the preserved samples. This indicates that drilling fluid contaminants had a negligible effect on the reservoir rock wettability. The experimental results also reveal similarities between saturation trends for the preserved‐LSWF and restored‐LSWF tests.
- 17 May 2017
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 53 (5) , 4427-4443
Open AccessIn situ characterization of wettability alteration and displacement mechanisms governing recovery enhancement due to low‐salinity waterflooding
A series of micro‐scale core‐flooding experiments were performed on reservoir core samples at elevated temperature and pressure conditions to develop better insights into wettability alteration and pore‐scale displacement mechanisms taking place during low‐salinity waterflooding (LSWF). Two individual miniature core samples were cut from a preserved reservoir whole core, saturated to establish initial reservoir fluid saturation conditions, and subsequently waterflooded with low‐salinity and high‐salinity brines. A third miniature sister core sample was also cut, solvent‐cleaned, and subjected to a dynamic wettability restoration process (to reestablish native state wettability) and then a low‐salinity waterflood. All samples were imaged during the experiments using a micro‐CT scanner to obtain fluid occupancy maps and measure in situ oil‐water contact angles. The results of the experiments performed on the preserved core samples show a significantly improved performance of low‐salinity waterflooding compared to that of high‐salinity waterflooding (HSWF). Pore‐scale contact angle measurements provide direct evidence of wettability alteration from weakly oil‐wet toward weakly water‐wet conditions during LSWF, whereas contact angles measured during HSWF remain unchanged. We believe that the reduction in oil‐water contact angles toward increased water‐wetness lowers the threshold water pressure needed to displace oil from some medium‐sized pore elements. Contact angles measured during the dynamic wettability restoration process show an equilibrium wettability state very similar to the initial one observed in the preserved samples. This indicates that drilling fluid contaminants had a negligible effect on the reservoir rock wettability. The experimental results also reveal similarities between saturation trends for the preserved‐LSWF and restored‐LSWF tests.
- 10 June 2014
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 32 (17) , 2123-2136
A Correlations Approach for Prediction of PVT Properties of Reservoir Oils
Reservoir oil properties are usually measured at reservoir temperature and are estimated at other temperature using empirical correlations. Fluid properties correlations cannot be used globally because of different characteristics of fluids in each area. Here, based on Iranian oil PVT data, new correlations have been developed to predict saturation pressure and oil formation volume factor at bubble point pressure. Validity and accuracy of these correlations were confirmed by comparing results of these correlations with experimental data. Checking the results shows that results for Iranian oil properties in this work are in good agreement with experimental data respect to other correlations.
- 10 June 2014
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 32 (17) , 2123-2136
A Correlations Approach for Prediction of PVT Properties of Reservoir Oils
Reservoir oil properties are usually measured at reservoir temperature and are estimated at other temperature using empirical correlations. Fluid properties correlations cannot be used globally because of different characteristics of fluids in each area. Here, based on Iranian oil PVT data, new correlations have been developed to predict saturation pressure and oil formation volume factor at bubble point pressure. Validity and accuracy of these correlations were confirmed by comparing results of these correlations with experimental data. Checking the results shows that results for Iranian oil properties in this work are in good agreement with experimental data respect to other correlations.