Faisal Wani
Faisal Wani has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Henk Polinder
Department of Maritime and Transport Technology, Delft University of Technology, Delft, The Netherlands
4 shared publications - Jianning Dong
DC System, Energy Conversion and Storage (DCES) Group, Faculty of Electrical Engineering, Mathematics and Computer Science (EEMCS), Delft University of Technology, Delft, CP, The Netherlands
4 shared publications - Udai Shipurkar
Maritime Research Institute of Netherlands, Wageningen, The Netherlands
2 shared publications - Antonio Jarquin Laguna
Delft University of Technology
1 shared publication - George Lavidas
Delft University of Technology
1 shared publication - Kaswar Mostafa
Institute for Energy Systems, University of Edinburgh, Edinburgh EH9 3DW, UK
1 shared publication
Latest Publications
- Open Access
Thermal Cycling in Converter IGBT Modules with Different Cooling Systems in Pitch- and Active Stall-Controlled Tidal Turbines
This paper compares active and passive cooling systems in tidal turbine power electronic converters. The comparison is based on the lifetime of the IGBT (insulated gate bipolar transistor) power modules, calculated from the accumulated fatigue due to thermal cycling. The lifetime analysis accounts for the influence of site conditions, namely turbulence and surface waves. Results indicate that active cooling results in a significant improvement in IGBT lifetime over passive cooling. However, since passive cooling systems are inherently more reliable than active systems, passive systems can present a better solution overall, provided adequate lifetime values are achieved. On another note, the influence of pitch control and active speed stall control on the IGBT lifetime was also investigated. It is shown that the IGBT modules in pitch-controlled turbines are likely to have longer lifetimes than their counterparts in active stall-controlled turbines for the same power rating. Overall, it is demonstrated that passive cooling systems can provide adequate cooling in tidal turbine converters to last longer than the typical lifetime of tidal turbines (>25 years), both for pitch-controlled and active speed stall-controlled turbines.
Open AccessThermal Cycling in Converter IGBT Modules with Different Cooling Systems in Pitch- and Active Stall-Controlled Tidal Turbines
This paper compares active and passive cooling systems in tidal turbine power electronic converters. The comparison is based on the lifetime of the IGBT (insulated gate bipolar transistor) power modules, calculated from the accumulated fatigue due to thermal cycling. The lifetime analysis accounts for the influence of site conditions, namely turbulence and surface waves. Results indicate that active cooling results in a significant improvement in IGBT lifetime over passive cooling. However, since passive cooling systems are inherently more reliable than active systems, passive systems can present a better solution overall, provided adequate lifetime values are achieved. On another note, the influence of pitch control and active speed stall control on the IGBT lifetime was also investigated. It is shown that the IGBT modules in pitch-controlled turbines are likely to have longer lifetimes than their counterparts in active stall-controlled turbines for the same power rating. Overall, it is demonstrated that passive cooling systems can provide adequate cooling in tidal turbine converters to last longer than the typical lifetime of tidal turbines (>25 years), both for pitch-controlled and active speed stall-controlled turbines.
- Open Access
Lifetime Analysis of IGBT Power Modules in Passively Cooled Tidal Turbine Converters
Thermal cycling is one of the major reasons for failure in power electronic converters. For submerged tidal turbine converters investigating this failure mode is critical in improving the reliability, and minimizing the cost of energy from tidal turbines. This paper considers a submerged tidal turbine converter which is passively cooled by seawater, and where the turbine has fixed-pitch blades. In this respect, this study is different from similar studies on wind turbine converters, which are mostly cooled by active methods, and where turbines are mostly pitch controlled. The main goal is to quantify the impact of surface waves and turbulence in tidal stream velocity on the lifetime of the converter IGBT (insulated gate bipolar transistor) modules. The lifetime model of the IGBT modules is based on the accumulation of fatigue due to thermal cycling. Results indicate that turbulence and surface waves can have a significant impact on the lifetime of the IGBT modules. Furthermore, to accelerate the speed of the lifetime calculation, this paper uses a modified approach by dividing the thermal models into low and high frequency models. The final calculated lifetime values suggest that relying on passive cooling could be adequate for the tidal converters as far as thermal cycling is concerned.
Open AccessLifetime Analysis of IGBT Power Modules in Passively Cooled Tidal Turbine Converters
Thermal cycling is one of the major reasons for failure in power electronic converters. For submerged tidal turbine converters investigating this failure mode is critical in improving the reliability, and minimizing the cost of energy from tidal turbines. This paper considers a submerged tidal turbine converter which is passively cooled by seawater, and where the turbine has fixed-pitch blades. In this respect, this study is different from similar studies on wind turbine converters, which are mostly cooled by active methods, and where turbines are mostly pitch controlled. The main goal is to quantify the impact of surface waves and turbulence in tidal stream velocity on the lifetime of the converter IGBT (insulated gate bipolar transistor) modules. The lifetime model of the IGBT modules is based on the accumulation of fatigue due to thermal cycling. Results indicate that turbulence and surface waves can have a significant impact on the lifetime of the IGBT modules. Furthermore, to accelerate the speed of the lifetime calculation, this paper uses a modified approach by dividing the thermal models into low and high frequency models. The final calculated lifetime values suggest that relying on passive cooling could be adequate for the tidal converters as far as thermal cycling is concerned.
- Open Access
- 1 April 2020
- Published by IntechOpen
Tidal Turbine Generators
Recently, tidal stream turbines have become a preferable mode of harvesting tidal energy. The main issue for low utilization of tidal energy is the high levelized cost of energy (LCoE) from tidal stream turbines. A major reason for this is the high operation and maintenance costs for submerged installations. A possible way of minimizing the LCoE and improving the availability is to use a flooded (or a wetgap) generator rather than a conventional airgap generator. Inside flooded generators, the gap between the stator and rotor is filled with the seawater. This architecture has the potential to improve cooling and reduce reliance on ancillary systems (e.g., bilge system), thereby improving reliability. The chapter begins with a brief description of the generator systems used in current tidal stream turbines. The focus of the chapter is, however, to give a basic insight into the design aspects of the flooded generators, and compares it with the currently used sealed airgap generators in tidal turbine systems.
- 1 April 2020
- Published by IntechOpen
Open AccessTidal Turbine Generators
Recently, tidal stream turbines have become a preferable mode of harvesting tidal energy. The main issue for low utilization of tidal energy is the high levelized cost of energy (LCoE) from tidal stream turbines. A major reason for this is the high operation and maintenance costs for submerged installations. A possible way of minimizing the LCoE and improving the availability is to use a flooded (or a wetgap) generator rather than a conventional airgap generator. Inside flooded generators, the gap between the stator and rotor is filled with the seawater. This architecture has the potential to improve cooling and reduce reliance on ancillary systems (e.g., bilge system), thereby improving reliability. The chapter begins with a brief description of the generator systems used in current tidal stream turbines. The focus of the chapter is, however, to give a basic insight into the design aspects of the flooded generators, and compares it with the currently used sealed airgap generators in tidal turbine systems.
- Open Access
- 2 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 6, 67543-67554
A Study on Passive Cooling in Subsea Power Electronics
This paper proposes a simplified approach to model the thermal behavior of the insulated gate bipolar transistors (IGBTs) in a subsea power electronic converter. The models are based on empirical relations for natural convection in water, and IGBT datasheet values. The proposed model can be used in the design of subsea converters and in the reliability analysis of their IGBTs. Experimental results are provided to validate the proposed thermal model. Suggestions are made to minimize the net thermal resistance by introducing a high conductivity thermal material as a mounting plate between the IGBT and the cabinet walls. Impact of the mounting plate dimensions, and material properties on the junction temperature of the IGBTs is studied. A case study analysis is made on a 100 kVA converter. Results indicate that the thermal spreading resistances in the mounting plate and the cabinet walls contribute significantly to the overall thermal resistance. Spreading resistances can be mitigated by appropriate design measures. Furthermore, it was observed that the passive cooling in water is not as effective as the forced water cooling. However, the low cost, simple design and higher reliability of passive cooling systems might make them a favorable choice for subsea systems.
- 2 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 6, 67543-67554
Open AccessA Study on Passive Cooling in Subsea Power Electronics
This paper proposes a simplified approach to model the thermal behavior of the insulated gate bipolar transistors (IGBTs) in a subsea power electronic converter. The models are based on empirical relations for natural convection in water, and IGBT datasheet values. The proposed model can be used in the design of subsea converters and in the reliability analysis of their IGBTs. Experimental results are provided to validate the proposed thermal model. Suggestions are made to minimize the net thermal resistance by introducing a high conductivity thermal material as a mounting plate between the IGBT and the cabinet walls. Impact of the mounting plate dimensions, and material properties on the junction temperature of the IGBTs is studied. A case study analysis is made on a 100 kVA converter. Results indicate that the thermal spreading resistances in the mounting plate and the cabinet walls contribute significantly to the overall thermal resistance. Spreading resistances can be mitigated by appropriate design measures. Furthermore, it was observed that the passive cooling in water is not as effective as the forced water cooling. However, the low cost, simple design and higher reliability of passive cooling systems might make them a favorable choice for subsea systems.