Masaki Takaoka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Interests
Masaki Takaoka has a total of 198 co-authors. Here are the top co-authors by number of shared publications:
- Kazuyuki Oshita
Department of Environmental Engineering, Graduate School of Engineering, Kyoto University, Kyoto, Japan
21 shared publications Kazuyuki Oshita
Department of Environmental Engineering, Graduate School of Engineering, Kyoto University, Kyoto, Japan
18 shared publicationsNobuo Takeda
Department of Environmental Engineering, Kyoto University, Kyoto 615-8540, Japan
15 shared publications- Kenji Shiota
Department of Environmental Engineering, Graduate School of Engineering, Kyoto University, Kyoto, Japan
10 shared publications - Takashi Fujimori
Environmental Sciences Course, Faculty of Advanced Science and Technology, Ryukoku University, 1-5 Yokotani, Seta Oe-cho, Otsu, Shiga 520-2194, Japan
10 shared publications Taketoshi Kusakabe
Department of Environmental Engineering, Graduate School of Engineering, Kyoto University, Kyoto, Japan
8 shared publications
Latest Publications
- Open Access
- 18 September 2026
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- p. 1-14
Metal waste in municipal solid waste incineration bottom ash: characterization, source identification, and recovery potential
The steady reduction in landfill capacity and limited land area for constructing new landfills require the recycling of municipal solid waste incineration bottom ash (MSWIBA). While most studies focus on using MSWIBA powder as a construction material, few have addressed metal waste characterization and recovery. This study quantified magnetic metal waste (MW) and nonmagnetic metal waste (NMW), which account for 14.40 ± 4.02 and 0.57 ± 0.20 wt% of MSWIBA, respectively. The identification of original discarded products, combined with elemental analysis, shows that the top 10 MW categories represent over 90% of the total MW weight, and most identifiable MW originated from daily necessities and common metal fittings. Notably, 16.50% of disposed metal waste, which should have been collected through separate collection systems, was found in MSWIBA. Some MW categories contained relatively high Cu, which could affect regenerated steel quality, while trace elements such as Cr, Mn, Co, Ni, As, and Mo were enriched in the magnetic ferrous powder. The estimated amounts of Ni and Co contained in MW landfilled annually correspond to 10.96% and 6.27% of Japan’s domestic demand. These findings indicate a significant recovery potential and call for improvements in upstream waste separation and downstream mechanical separation.
- 18 September 2026
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- p. 1-14
Open AccessMetal waste in municipal solid waste incineration bottom ash: characterization, source identification, and recovery potential
The steady reduction in landfill capacity and limited land area for constructing new landfills require the recycling of municipal solid waste incineration bottom ash (MSWIBA). While most studies focus on using MSWIBA powder as a construction material, few have addressed metal waste characterization and recovery. This study quantified magnetic metal waste (MW) and nonmagnetic metal waste (NMW), which account for 14.40 ± 4.02 and 0.57 ± 0.20 wt% of MSWIBA, respectively. The identification of original discarded products, combined with elemental analysis, shows that the top 10 MW categories represent over 90% of the total MW weight, and most identifiable MW originated from daily necessities and common metal fittings. Notably, 16.50% of disposed metal waste, which should have been collected through separate collection systems, was found in MSWIBA. Some MW categories contained relatively high Cu, which could affect regenerated steel quality, while trace elements such as Cr, Mn, Co, Ni, As, and Mo were enriched in the magnetic ferrous powder. The estimated amounts of Ni and Co contained in MW landfilled annually correspond to 10.96% and 6.27% of Japan’s domestic demand. These findings indicate a significant recovery potential and call for improvements in upstream waste separation and downstream mechanical separation.
- 17 September 2026
- Published by Elsevier in Bioresource Technology
- Vol. 464 (Pt B) , 135859
Thermochemical regeneration of iron-based materials using syngas derived from carbon dioxide gasification of digested sludge biochar
- 17 September 2026
- Published by Elsevier in Bioresource Technology
- Vol. 464 (Pt B) , 135859
Thermochemical regeneration of iron-based materials using syngas derived from carbon dioxide gasification of digested sludge biochar
- 5 June 2026
- Published by Elsevier in Bioresource Technology
- Vol. 458, 135090
Impact of zero-valent iron on carbon dioxide biomethanation under mesophilic and thermophilic conditions
- 5 June 2026
- Published by Elsevier in Bioresource Technology
- Vol. 458, 135090
Impact of zero-valent iron on carbon dioxide biomethanation under mesophilic and thermophilic conditions
- Open Access
- 20 May 2026
- Published by Elsevier in Waste Management
- Vol. 220, 115609
Global warming potential assessment of municipal solid waste management in Greater Lisbon
- 20 May 2026
- Published by Elsevier in Waste Management
- Vol. 220, 115609
Open AccessGlobal warming potential assessment of municipal solid waste management in Greater Lisbon
- Open Access
- 3 April 2026
- Published by Elsevier in Waste Management
- Vol. 217, 115498
Exploratory modeling to estimate major elements contents of woody biomass ash from stokers, fluidized beds and gasification reactors
- 3 April 2026
- Published by Elsevier in Waste Management
- Vol. 217, 115498
Open AccessExploratory modeling to estimate major elements contents of woody biomass ash from stokers, fluidized beds and gasification reactors
- Open Access
- 19 February 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 229
Prediction of woody biomass ash potential for utilization as fertilizer and cement material
- 19 February 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 229
Open AccessPrediction of woody biomass ash potential for utilization as fertilizer and cement material
- Open Access
- 13 January 2026
- Published by Elsevier in Waste Management
- Vol. 212, 115348
Comparative study on pyrolysis characteristics of common fractions from real municipal solid waste using Py-GC/MS and principal component analysis
- 13 January 2026
- Published by Elsevier in Waste Management
- Vol. 212, 115348
Open AccessComparative study on pyrolysis characteristics of common fractions from real municipal solid waste using Py-GC/MS and principal component analysis
- Open Access
- 22 August 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (35) , 39482-39493
Lipid Extraction from Wet Polymer-Flocculated Chlorella sorokiniana Using Liquefied Dimethyl Ether without Centrifugation and Drying Pretreatment
The energy intensive nature of harvesting microalgae by centrifugation and drying results in a low energy profit ratio for biofuel production from wet microalgae. To address this, microalgal cultures can be flocculated by polymers to reduce energy consumption and avoid centrifugation. Additionally, lipids can be directly extracted from wet microalgae harvested by centrifugation using liquefied dimethyl ether (DME) to reduce energy consumption. In this study, we investigated the lipid extraction from the green alga, Chlorella sorokiniana (C. sorokiniana), flocculated with amphoteric and cationic polymers using liquefied DME, without centrifugation and drying pretreatment. Although the addition of amphoteric polymer did not interfere with lipid extraction by liquefied DME, the amount of lipids extracted by ethanol from flocculated C. sorokiniana decreased. The addition of cationic polymers also interferes with lipid extraction using liquefied DME, chloroform–methanol mixtures, and ethanol. Surface functional group measurements revealed that the amphoteric and cationic polymer flocculants were insoluble in these solvents, remained in the residue, and did not contaminate the extracted lipids. Thus, the amphoteric flocculant KA305BH was found to be effective for lipid extraction with liquefied DME from C. sorokiniana. The proposed approach can facilitate the energy efficient production of biofuel from wet microalgae.
- 22 August 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (35) , 39482-39493
Open AccessLipid Extraction from Wet Polymer-Flocculated Chlorella sorokiniana Using Liquefied Dimethyl Ether without Centrifugation and Drying Pretreatment
The energy intensive nature of harvesting microalgae by centrifugation and drying results in a low energy profit ratio for biofuel production from wet microalgae. To address this, microalgal cultures can be flocculated by polymers to reduce energy consumption and avoid centrifugation. Additionally, lipids can be directly extracted from wet microalgae harvested by centrifugation using liquefied dimethyl ether (DME) to reduce energy consumption. In this study, we investigated the lipid extraction from the green alga, Chlorella sorokiniana (C. sorokiniana), flocculated with amphoteric and cationic polymers using liquefied DME, without centrifugation and drying pretreatment. Although the addition of amphoteric polymer did not interfere with lipid extraction by liquefied DME, the amount of lipids extracted by ethanol from flocculated C. sorokiniana decreased. The addition of cationic polymers also interferes with lipid extraction using liquefied DME, chloroform–methanol mixtures, and ethanol. Surface functional group measurements revealed that the amphoteric and cationic polymer flocculants were insoluble in these solvents, remained in the residue, and did not contaminate the extracted lipids. Thus, the amphoteric flocculant KA305BH was found to be effective for lipid extraction with liquefied DME from C. sorokiniana. The proposed approach can facilitate the energy efficient production of biofuel from wet microalgae.
- Open Access
- 20 July 2025
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- p. 1-21
Historical trends, roles, and future challenges of sewage sludge thermal treatment in Japan
In Japan, almost all sewage sludge is not sent to landfills due to the country’s limited land availability and the need to prevent global warming. Most sludges undergo thermal treatment. Sewage sludge incineration is popular. Recent technological advancements include fluidized bed and step grate stoker incinerators. Energy-saving and recovery technologies have been gradually developed. Currently, sludge thermal drying, melting, carbonization, and gasification are commercially implemented; energy-saving and recycling strategies are steadily progressing. In particular, the conversion of sewage sludge into fuel and fertilizer has increased in recent years. These new technologies enhance energy efficiency, reduce CO2 emissions, and, notably, decrease N2O emissions. Each technology and its applications are distinct. Thermal treatments are expected to continue as a measure against organic pollutants in sewage sludge. Continued technological development will contribute to achieving a carbon-neutral society, promoting a circular economy, and ensuring food security.
- 20 July 2025
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- p. 1-21
Open AccessHistorical trends, roles, and future challenges of sewage sludge thermal treatment in Japan
In Japan, almost all sewage sludge is not sent to landfills due to the country’s limited land availability and the need to prevent global warming. Most sludges undergo thermal treatment. Sewage sludge incineration is popular. Recent technological advancements include fluidized bed and step grate stoker incinerators. Energy-saving and recovery technologies have been gradually developed. Currently, sludge thermal drying, melting, carbonization, and gasification are commercially implemented; energy-saving and recycling strategies are steadily progressing. In particular, the conversion of sewage sludge into fuel and fertilizer has increased in recent years. These new technologies enhance energy efficiency, reduce CO2 emissions, and, notably, decrease N2O emissions. Each technology and its applications are distinct. Thermal treatments are expected to continue as a measure against organic pollutants in sewage sludge. Continued technological development will contribute to achieving a carbon-neutral society, promoting a circular economy, and ensuring food security.
- Open Access
- 25 June 2025
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- p. 1-14
Municipal solid waste management in Portugal using material flow analysis: regional assessment
The rapid economic and utility value loss of materials, which then become waste, has brought several challenges in managing municipal solid waste (MSW). Material Flow Analysis (MFA) is widely employed in MSW management for its ability to provide in-depth analysis of waste quantitative flows, providing a robust baseline for further environmental and economic assessments. In complex, interdisciplinary decision-making, a clear identification of MSW management (MSWM) systems is essential, particularly for efficient resource use at regional scales. This study applied MFA to assess MSWM systems at both national and regional levels across Portugal for 2015, 2020, and 2021, analyzing seven regions, including mainland Portugal. Data were sourced from annual sector reports. Results indicate substantial regional disparities, with landfill disposal rates ranging from ~ 40% in metropolitan areas to as high as 84% in other regions—falling short of European Union targets. The COVID-19 pandemic exacerbated landfill use across all regions. Despite high household organic waste generation, organic valorization remains limited, and residual fractions sent to landfills are also high. Increasing investments in source separation, especially for organic waste, and waste valorization facilities would enhance material valorization and reduce landfill dependence. This study underscores the urgent need for solutions to achieve ambitious targets.
- 25 June 2025
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- p. 1-14
Open AccessMunicipal solid waste management in Portugal using material flow analysis: regional assessment
The rapid economic and utility value loss of materials, which then become waste, has brought several challenges in managing municipal solid waste (MSW). Material Flow Analysis (MFA) is widely employed in MSW management for its ability to provide in-depth analysis of waste quantitative flows, providing a robust baseline for further environmental and economic assessments. In complex, interdisciplinary decision-making, a clear identification of MSW management (MSWM) systems is essential, particularly for efficient resource use at regional scales. This study applied MFA to assess MSWM systems at both national and regional levels across Portugal for 2015, 2020, and 2021, analyzing seven regions, including mainland Portugal. Data were sourced from annual sector reports. Results indicate substantial regional disparities, with landfill disposal rates ranging from ~ 40% in metropolitan areas to as high as 84% in other regions—falling short of European Union targets. The COVID-19 pandemic exacerbated landfill use across all regions. Despite high household organic waste generation, organic valorization remains limited, and residual fractions sent to landfills are also high. Increasing investments in source separation, especially for organic waste, and waste valorization facilities would enhance material valorization and reduce landfill dependence. This study underscores the urgent need for solutions to achieve ambitious targets.