Sergey V. Fedorov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sergey V. Fedorov has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Valery Belousov
Baikov Institute of Metallurgy and Materials Science Russian Academy of Sciences 49 Leninsky Pr. 119334 Moscow Russian Federation
24 shared publications - I. V. Kulbakin
Russian Academy of Sciences
8 shared publications - Igor V. Zagaynov
A. A. Baikov Institute of Metallurgy and Materials Science, Moscow, Russia
7 shared publications - Anton S. Lysenkov
A.A.Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, Leninsky pr. 49, 119334 Moscow, Russia
5 shared publications - Anton A. Klimashin
Russian Academy of Sciences
4 shared publications I V Kulbakin
4 shared publications
Latest Publications
- 26 October 2026
- Published by Elsevier in Materials Research Bulletin
- Vol. 207
Oxygen exchange kinetics in cells with a Bi2O3-Ag electrolyte and bismuth ruthenate-based electrodes
- 26 October 2026
- Published by Elsevier in Materials Research Bulletin
- Vol. 207
Oxygen exchange kinetics in cells with a Bi2O3-Ag electrolyte and bismuth ruthenate-based electrodes
- 5 November 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (30) , 64903-64909
Ceramic and liquid-solid composites Bi2Mn4O10 – Bi2O3 for oxygen ion transport membranes
- 5 November 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (30) , 64903-64909
Ceramic and liquid-solid composites Bi2Mn4O10 – Bi2O3 for oxygen ion transport membranes
- 12 August 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (26) , 49403-49409
Effect of hot-pressing temperature on the properties of Si3N4 ceramics with a low content of eutectic CaO–Al2O3 sintering additive
- 12 August 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (26) , 49403-49409
Effect of hot-pressing temperature on the properties of Si3N4 ceramics with a low content of eutectic CaO–Al2O3 sintering additive
- 28 May 2025
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 54 (24) , 9489-9493
Electrical conductivity of low-doped ceria-based ceramics
Ceria-based ceramic materials (M0.01Ce0.99O2) were synthesized by a co-precipitation method and sintered at 1000 °C for 4 h in air. The electrical conductivity of these systems was measured by AC impedance spectroscopy at 500–750 °C in air. Introduction of small amounts of dopants such as copper, bismuth, samarium, and neodymium increased this parameter by 4–5 times. However, the optimal dopants were Bi or Nd due to their higher conductivity and oxide ion transference number.
- 28 May 2025
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 54 (24) , 9489-9493
Electrical conductivity of low-doped ceria-based ceramics
Ceria-based ceramic materials (M0.01Ce0.99O2) were synthesized by a co-precipitation method and sintered at 1000 °C for 4 h in air. The electrical conductivity of these systems was measured by AC impedance spectroscopy at 500–750 °C in air. Introduction of small amounts of dopants such as copper, bismuth, samarium, and neodymium increased this parameter by 4–5 times. However, the optimal dopants were Bi or Nd due to their higher conductivity and oxide ion transference number.
- 14 November 2024
- Published by Elsevier in Ceramics International
- Vol. 51 (2) , 2335-2339
Electrochemical characterization of Bi3Ru3O11 – 40 wt% Bi1.6Er0.4O3 as an EOG electrode material
- 14 November 2024
- Published by Elsevier in Ceramics International
- Vol. 51 (2) , 2335-2339
Electrochemical characterization of Bi3Ru3O11 – 40 wt% Bi1.6Er0.4O3 as an EOG electrode material
- 2 January 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (4) , 2870-2876
Solutocapillary transport of oxygen bubbles in a diffusion-bubbling membrane core
Bubbles are extensively explored as gas and energy carriers. However, despite notable progress, the bubble transport mechanisms are still poorly understood.
- 2 January 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (4) , 2870-2876
Solutocapillary transport of oxygen bubbles in a diffusion-bubbling membrane core
Bubbles are extensively explored as gas and energy carriers. However, despite notable progress, the bubble transport mechanisms are still poorly understood.
- 1 September 2023
- Published by Pleiades Publishing Ltd in Inorganic Materials
- Vol. 59 (9) , 970-976
Phase Composition and Physicomechanical Properties of β-Sialons Prepared Using NaF as a Sintering Aid
We have studied the effect of sodium fluoride as a sintering aid for β-sialons on the phase composition and physicomechanical properties of Si5AlON7 and Si4Al2O2N6. Two-step high-temperature firing of the β-sialons in the presence of NaF under a nitrogen atmosphere has been shown to cause no significant changes in the phase composition of the materials. The density and microhardness of the materials prepared using 0.5 and 5.0 wt % NaF are lower than those of the materials prepared without sintering aids, but the bending strength is higher by up to 14.3% in the case of Si5AlON7 prepared using 0.5 wt % NaF and by 4.9% in the case of Si4Al2O2N6 prepared using 5.0 wt % NaF.
- 1 September 2023
- Published by Pleiades Publishing Ltd in Inorganic Materials
- Vol. 59 (9) , 970-976
Phase Composition and Physicomechanical Properties of β-Sialons Prepared Using NaF as a Sintering Aid
We have studied the effect of sodium fluoride as a sintering aid for β-sialons on the phase composition and physicomechanical properties of Si5AlON7 and Si4Al2O2N6. Two-step high-temperature firing of the β-sialons in the presence of NaF under a nitrogen atmosphere has been shown to cause no significant changes in the phase composition of the materials. The density and microhardness of the materials prepared using 0.5 and 5.0 wt % NaF are lower than those of the materials prepared without sintering aids, but the bending strength is higher by up to 14.3% in the case of Si5AlON7 prepared using 0.5 wt % NaF and by 4.9% in the case of Si4Al2O2N6 prepared using 5.0 wt % NaF.
- 15 February 2022
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 105 (6) , 4532-4541
A core‐shell structured diffusion‐bubbling membrane for efficient oxygen separation: Formation and transport properties
The newly developed core‐shell structured molten oxide membranes with fast combined diffusion‐bubbling oxygen mass transfer and theoretically infinite selectivity are of technological interest because of their high separation efficiency. In this article, a core‐shell structured molten V 2 O 5 –Cu 2 O‐ based diffusion‐bubbling membrane was prepared by one‐step thermal treatment of initial CuO–25 wt.% Cu 5 V 2 O 10 ceramic composite in a chemical field (under an oxygen partial pressure difference across the composite) above copper vanadate peritectic transformation temperature (816°C). Oxygen fluxes through the membrane were measured at 830°C, using either gas mixtures (O 2 + N 2 ) with different oxygen concentrations or air as feed gas at the shell of the membrane and helium (He) as sweep gas. Oxygen flux through the membrane with a shell thickness of 0.15–0.61 mm was 3.8·10 –8 –1.4·10 –7 mol/cm 2 /s under an oxygen partial pressure difference of 0.1 –0.75 atm, respectively. The effect of oxygen partial pressure on the thickness of the membrane shell is found. The relationship between membrane shell thickness, oxygen partial pressure difference across the membrane, and oxygen permeation flux through the membrane is established. Oxygen permeation flux through the dual‐phase MIEC membrane shell is described in terms of the diffusion model. Oxygen permeation flux through the membrane core is described both within the framework of the stationary model and nonstationary model for uniform (the membrane thickness is much larger than the characteristic distance of bubble dynamic relaxation) and accelerated (the membrane thickness is comparable to the characteristic distance of bubble dynamic relaxation) bubble motion in a viscous oxide melt, respectively.
- 15 February 2022
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 105 (6) , 4532-4541
A core‐shell structured diffusion‐bubbling membrane for efficient oxygen separation: Formation and transport properties
The newly developed core‐shell structured molten oxide membranes with fast combined diffusion‐bubbling oxygen mass transfer and theoretically infinite selectivity are of technological interest because of their high separation efficiency. In this article, a core‐shell structured molten V 2 O 5 –Cu 2 O‐ based diffusion‐bubbling membrane was prepared by one‐step thermal treatment of initial CuO–25 wt.% Cu 5 V 2 O 10 ceramic composite in a chemical field (under an oxygen partial pressure difference across the composite) above copper vanadate peritectic transformation temperature (816°C). Oxygen fluxes through the membrane were measured at 830°C, using either gas mixtures (O 2 + N 2 ) with different oxygen concentrations or air as feed gas at the shell of the membrane and helium (He) as sweep gas. Oxygen flux through the membrane with a shell thickness of 0.15–0.61 mm was 3.8·10 –8 –1.4·10 –7 mol/cm 2 /s under an oxygen partial pressure difference of 0.1 –0.75 atm, respectively. The effect of oxygen partial pressure on the thickness of the membrane shell is found. The relationship between membrane shell thickness, oxygen partial pressure difference across the membrane, and oxygen permeation flux through the membrane is established. Oxygen permeation flux through the dual‐phase MIEC membrane shell is described in terms of the diffusion model. Oxygen permeation flux through the membrane core is described both within the framework of the stationary model and nonstationary model for uniform (the membrane thickness is much larger than the characteristic distance of bubble dynamic relaxation) and accelerated (the membrane thickness is comparable to the characteristic distance of bubble dynamic relaxation) bubble motion in a viscous oxide melt, respectively.
- 30 September 2021
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 23 (41) , 24029-24038
Bubble nucleation in core–shell structured molten oxide-based membranes with combined diffusion-bubbling oxygen mass transfer: experiment and theory
Oxygen-selective membranes are likely to play a leading part in the future separation processes relevant to energy engineering. A newly developed molten copper and vanadium oxide-based diffusion-bubbling membrane with core–shell structure and fast combined oxygen mass transfer is a promising candidate for efficient oxygen separation. In this work, the oxygen bubble nucleation and transport properties of the diffusion-bubbling membrane were experimentally and theoretically studied. Bubble size distribution and cumulative oxygen flux have been plotted as functions of oxygen partial pressure. The relationship between the bubble density, oxygen partial pressure, and oxygen permeation flux was established. The oxygen flux and bubble density vary in the ranges of 3.2 × 10−8–1.4 × 10−7 mol cm−2 s−1 and 1.3 × 1013–5.8 × 1013 m−3 at ΔP O2 = 0.1–0.75 atm, respectively. The mechanisms of homogeneous, heterogeneous, pseudo-classical and non-classical nucleation are reviewed within the framework of the Cahn–Hilliard model. It is shown that the homogeneous nucleation mechanism is most likely in the membrane core. The estimated values of the interfacial tension, energy barrier, and rate nucleation are 0.02 J m−2, 5 kT, and 4 × 1029 m−3 s−1, respectively.
- 30 September 2021
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 23 (41) , 24029-24038
Bubble nucleation in core–shell structured molten oxide-based membranes with combined diffusion-bubbling oxygen mass transfer: experiment and theory
Oxygen-selective membranes are likely to play a leading part in the future separation processes relevant to energy engineering. A newly developed molten copper and vanadium oxide-based diffusion-bubbling membrane with core–shell structure and fast combined oxygen mass transfer is a promising candidate for efficient oxygen separation. In this work, the oxygen bubble nucleation and transport properties of the diffusion-bubbling membrane were experimentally and theoretically studied. Bubble size distribution and cumulative oxygen flux have been plotted as functions of oxygen partial pressure. The relationship between the bubble density, oxygen partial pressure, and oxygen permeation flux was established. The oxygen flux and bubble density vary in the ranges of 3.2 × 10−8–1.4 × 10−7 mol cm−2 s−1 and 1.3 × 1013–5.8 × 1013 m−3 at ΔP O2 = 0.1–0.75 atm, respectively. The mechanisms of homogeneous, heterogeneous, pseudo-classical and non-classical nucleation are reviewed within the framework of the Cahn–Hilliard model. It is shown that the homogeneous nucleation mechanism is most likely in the membrane core. The estimated values of the interfacial tension, energy barrier, and rate nucleation are 0.02 J m−2, 5 kT, and 4 × 1029 m−3 s−1, respectively.
- 8 July 2021
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 37 (28) , 8370-8381
Oxygen-Selective Diffusion-Bubbling Membranes with Core–Shell Structure: Bubble Dynamics and Unsteady Effects
Oxygen is the second-largest-volume industrial gas that is mainly produced using cryogenic air separation. However, the state-of-the-art cryogenic technology thermodynamic efficiency has approached a theoretical limit as near as is practicable. Therefore, there is stimulus to develop an alternative technology for efficient oxygen separation from air. Mixed ionic electronic-conducting (MIEC) ceramic membrane-based oxygen separation technology could become this alternative, but commercialization aspects, including cost, have revealed inadequacies in ceramic membrane materials. Currently, diffusion-bubbling molten oxide membrane-based oxygen separation technology is being developed. It is a potentially disruptive technology that would propose an improvement in oxygen purity and a reduction in capital costs. Bubbles play an important role in ensuring the oxygen mass transfer in diffusion-bubbling membranes. However, there is not sufficient understanding of the bubble dynamics. This understanding is important to be able to control transport properties of these membranes and assess their potential for technological application. The aim of this feature article is to highlight the progress made in developing this understanding and specify the directions for future research.
- 8 July 2021
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 37 (28) , 8370-8381
Oxygen-Selective Diffusion-Bubbling Membranes with Core–Shell Structure: Bubble Dynamics and Unsteady Effects
Oxygen is the second-largest-volume industrial gas that is mainly produced using cryogenic air separation. However, the state-of-the-art cryogenic technology thermodynamic efficiency has approached a theoretical limit as near as is practicable. Therefore, there is stimulus to develop an alternative technology for efficient oxygen separation from air. Mixed ionic electronic-conducting (MIEC) ceramic membrane-based oxygen separation technology could become this alternative, but commercialization aspects, including cost, have revealed inadequacies in ceramic membrane materials. Currently, diffusion-bubbling molten oxide membrane-based oxygen separation technology is being developed. It is a potentially disruptive technology that would propose an improvement in oxygen purity and a reduction in capital costs. Bubbles play an important role in ensuring the oxygen mass transfer in diffusion-bubbling membranes. However, there is not sufficient understanding of the bubble dynamics. This understanding is important to be able to control transport properties of these membranes and assess their potential for technological application. The aim of this feature article is to highlight the progress made in developing this understanding and specify the directions for future research.