JCJinyoun Cho

Jinyoun Cho

*This is an algorithmically generated author record based on publicly available information.

Jinyoun Cho has a total of 96 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Tunable dual-morphology porous germanium with enhanced thermal stability via low-temperature bipolar etching

    by L. Demoulin, B. Ilahi, J. Cho, K. Dessein, A. Chapotot, R. Gosselin, A. Boucherif, D. Machon, M. Siaj

    Low-temperature electrochemical etching creates a dual sponge-like and diamond morphology in germanium, opening new opportunities for thermally robust industrial processes.

  • Investigation of the impact of surface state on Ge membrane quality obtained with porous lift-off

    by Imad-Eddine Mokeddem, Ahmed Ayari, Radouane En-Nadir, Gbenro Folaranmi, Alexandre Chapotot, Jinyoun Cho, Kristof Dessein, Denis Machon, Abderraouf Boucherif

    Germanium (Ge) substrates are widely used for the integration of III–V-based devices owing to their suitable material properties. However, their high cost, driven by material scarcity and complex processing requirements, remains a major limitation for large-scale production. In this work, the growth of III–V materials on Ge nanomembranes (Ge NMs) fabricated from unpolished Ge substrates was investigated. The results demonstrate a promising approach for replacing costly epi-ready, polished Ge wafers with unpolished Ge wafers, potentially enabling a more cost-effective substrate platform for III–V device integration. Using a porous lift-off approach on the 4-in. unpolished wafers, homogeneous porous Ge layers were achieved. These layers enabled the formation of monocrystalline Ge NMs with root mean square roughness values ranging from 0.7 to 1.4 nm at the nanoscale and preserved crystallographic orientation and allowed subsequent detachment. Furthermore, the nano-membranes supported high-quality III–V epitaxial growth, demonstrating a promising pathway toward lower-cost scalable production of III–V on Ge devices.

  • Open Access

    Porous-lift-off germanium membranes as lightweight, flexible, and cost-effective template for III-V space solar cells: a review

    by Azmat Ali, Radouane En-Nadir, Chahinaz Khouloud Mahboub, Imad-Eddine Mokeddem, Ahmed Ayari, Brieuc Mével, Jérôme Ripa, Artur Turala, Alexandre Chapotot, Priyanka Proost, et al.

  • Open Access

    Comprehensive investigation of thermal induced reorganization of porous-germanium structures

    by Ahmed Ayari, Bouraoui Ilahi, Roxana Arvinte, Tadeáš Hanuš, Laurie Mouchel, Jinyoun Cho, Kristof Dessein, Denis Machon, Abderraouf Boucherif


  • Overview of Engineered Germanium Substrate Development for Affordable Large-Volume Multijunction Solar Cells

    by Jinyoun Cho, Valérie Depauw, Alexandre Chapotot, Waldemar Schreiber, Tadeáš Hanuš, Nicolas Paupy, Valentin Daniel, Guillaume Courtois, Bouraoui Ilahi, Abderraouf Boucherif, et al.

    New massive markets for space multijunction solar cells are being discussed globally. For such an explosive increase in demand to materialize, a more sustainable and affordable Ge substrate technology is required. To this end, lithography-based Ge-on-Nothing and electrochemical process-based porous Ge wafers were developed. Both approaches yield uniform and smooth monocrystalline Ge-on-Ge engineered substrates after annealing, of which the top layer is weakly attached to the parent substrate. High-quality space solar cells were grown on them, followed by successful foil detachment and surface reconditioning. These results clearly demonstrate the feasibility of the reusable Ge substrate concept.


  • Open Access

    Sustainable Production of Ultrathin Ge Freestanding Membranes

    by Tadeáš Hanuš, Bouraoui Ilahi, Jinyoun Cho, Kristof Dessein, Abderraouf Boucherif

    Germanium (Ge) is a critical material for applications in space solar cells, integrated photonics, infrared imaging, sensing, and photodetectors. However, the corresponding cost and limited availability hinder its potential for widespread applications. However, using Ge freestanding membranes (FSMs) allows for a significant reduction in the material consumption during device fabrication while offering additional advantages such as lightweight and flexible form factor for novel applications. In this work, we present the Ge FSM production process involving sequential porous Ge (PGe) structure formation, Ge membrane epitaxial growth, detachment, substrate cleaning, and subsequent reuse. This process enables the fabrication of multiple high-quality monocrystalline Ge FSMs from the same substrate through efficient substrate reuse at a 100 mm wafer scale by a simple and low-cost chemical cleaning process. A uniform, high-quality PGe layer is produced on the entire recovered substrate. By circumventing the use of conventional high-cost chemical–mechanical polishing or even substantial chemical wet-etching, and by using an optimized PGe structure with reduced thickness, the developed process allows for both cost and an environmental impact reduction in Ge FSMs production, lowering the amount of Ge used per membrane fabrication. Moreover, this process employs large-scale compatible techniques paving the way for the sustainable production of group IV FSMs for next-generation flexible optoelectronics.


  • Open Access

    Enhancing minority carrier lifetime in Ge: Insights from HF and HCl cleaning procedures

    by Alexandre Chapotot, Jérémie Chrétien, Oleh Fesiienko, Erwine Pargon, Jinyoun Cho, Kristof Dessein, Abderraouf Boucherif, Gwenaëlle Hamon, Maxime Darnon

    Efficiently passivating germanium (Ge) surfaces is crucial to reduce the unwanted recombination current in high-performance devices. Chemical surface cleaning is critical to remove surface contaminants and Ge oxides, ensuring effective surface passivation after dielectric deposition. However, Ge oxides can rapidly regrow upon air exposure. To understand the surface evolution after wet cleaning, we present a comprehensive study comparing HF and HCl deoxidation steps on p-type Ge surfaces and monitor the surface as a function of air exposure time. Distinct oxide regrowth dynamics are observed: HF-treated samples exhibit swift regrowth of all Ge oxide states, whereas HCl-treated Ge surfaces exhibit a lower concentration of low degrees of oxidation and slower or no regrowth of high oxide states even after 110 min of air exposure. In addition, the presence of Ge–Cl bonds induces different oxidation dynamics compared to the Ge–OH bonds resulting from HF cleaning. This leads to varying surface electronic band structures, with HF-treated Ge exhibiting a strong positive band bending (+0.20 eV). Conversely, HCl-treated samples display a lower band curvature (+0.07 eV), mostly due to the presence of Ge–Cl bonds on the Ge surface. During air exposure, the increased GeOx coverage significantly reduces the band bending after HF, while a constant band bending is observed after HCl. Finally, these factors induce a reduction in the surface recombination velocity after wet etching. Combining both chemical and field-induced passivation, HF-treated Ge without rinsing exceeds 800 μs.


  • Potential monitoring during Ge electrochemical etching: Towards tunable double porosity layers

    by Tadeáš Hanuš, Laurie Mouchel, Bouraoui Ilahi, Arthur Dupuy, Jinyoun Cho, Kristof Dessein, Abderraouf Boucherif


  • Multiple-reuse of Ge Substrates: Towards Cost-effective and Sustainable III-V Solar Cells Fabrication

    by Alexandre Chapotot, Bouraoui Ilahi, Tadeáš Hanuš, Gwenaëlle Hamon, Jinyoun Cho, Kristof Dessein, Christian Dubuc, Maxime Darnon, Abderraouf Boucherif

    High efficiency solar cells based on III-V layers on Ge substrates are commonly used for space devices, but their high cost, partly due to Ge substrate, make them less suitable for terrestrial photovoltaic applications. The porous lift-off process offers a solution for detaching a thin, flexible, and lightweight cell and reusing the substrate, potentially making these solar cells more cost-effective. To date, only one reuse of the substrate has been proven. However, further examination of multiple reuse cycles is crucial in understanding the trends in the surface of the wafer over cycles. The HF-based wet chemistry employed in this study, allows for the substrate to be reused three times by removing the broken pillars that remain after each porous lift-off cycle. The reusability of the substrate is guaranteed due to the smooth and blemish-free surfaces with low RMS roughness achieved through reconditioning. Even after three porous lift-off cycles, the epitaxial layer remains monocrystalline with a roughness of only 3 nm, making it suitable for solar cell growth. These findings open up the possibility for a more affordable and sustainable method of producing high efficiency solar cells, reducing costs by a factor of 4 and Ge consumption by a factor of 19 compared to traditional manufacturing methods.

  • Open Access

    Overview of Engineered Germanium Substrate Development for Affordable Large-Volume Multi-Junction Solar Cells

    by Jinyoun Cho, Valérie Depauw, Alexandre Chapotot, Waldemar Schreiber, Tadeáš Hanuš, Nicolas Paupy, Valentin Daniel, Guillaume Courtois, Bouraoui Ilahi, Abderraouf Boucherif, et al.

    New massive markets for space multi-junction solar cells are being discussed globally. For such an explosive increase in demand to materialize, a more sustainable and affordable Ge substrate technology is required. To this end, lithography-based Ge-on-Nothing and electrochemical process-based porous Ge wafers were developed. Both approaches yield uniform and smooth monocrystalline Ge-on-Ge engineered substrates after annealing, of which the top layer is weakly attached to the mother substrate. High-quality space solar cells were grown on them, followed by successful foil detachment and surface reconditioning. These results clearly demonstrate the feasibility of the reusable Ge substrate concept.