Mehdi Firdaouss
Research Subjects
Research Interests
Mehdi Firdaouss has a total of 278 co-authors. Here are the top co-authors by number of shared publications:
- Jonathan Gerardin
IRFM
11 shared publications M. Missirlian
CEA, IRFM, F-13108 Saint Paul-Lez-Durance, France
8 shared publications- Mathilde Diez
IRFM, CEA Cadarache, Saint-Paul-lez-Durance, Provence-Alpes-Côte d'Azu, FRANCE
8 shared publications Y. Corre
8 shared publicationsC. Pocheau
6 shared publicationsM. Richou
6 shared publications
Latest Publications
- Open Access
- 20 November 2025
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 45
Promising cooling concepts for enhanced JT-60SA tungsten actively cooled divertor
- 20 November 2025
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 45
Open AccessPromising cooling concepts for enhanced JT-60SA tungsten actively cooled divertor
- Open Access
- 8 December 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 42
A new design concept of actively cooled plasma-facing units for the divertors of fusion reactors
- 8 December 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 42
Open AccessA new design concept of actively cooled plasma-facing units for the divertors of fusion reactors
- Open Access
- 28 October 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 41
Evolution and cleaning of the deposit layers on the lower divertor of WEST fully equipped with ITER grade components
- 28 October 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 41
Open AccessEvolution and cleaning of the deposit layers on the lower divertor of WEST fully equipped with ITER grade components
- Open Access
- 12 October 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 41
Toroidal distribution of heat load on castellated plasma facing components for lower divertor target in EAST
- 12 October 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 41
Open AccessToroidal distribution of heat load on castellated plasma facing components for lower divertor target in EAST
- Open Access
- 23 December 2023
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 38
Development of Boron Coatings for antenna protection limiters in the WEST Tokamak
- 23 December 2023
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 38
Open AccessDevelopment of Boron Coatings for antenna protection limiters in the WEST Tokamak
- Open Access
- 18 October 2023
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 37
Infrared detection of tungsten cracking on actively cooled ITER-like component during high power experiment in WEST
- 18 October 2023
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 37
Open AccessInfrared detection of tungsten cracking on actively cooled ITER-like component during high power experiment in WEST
- 27 March 2023
- Published by Elsevier in Fusion Engineering and Design
- Vol. 193
Manufacturing, testing and installation of the full tungsten actively cooled ITER-like divertor in the WEST tokamak
- 27 March 2023
- Published by Elsevier in Fusion Engineering and Design
- Vol. 193
Manufacturing, testing and installation of the full tungsten actively cooled ITER-like divertor in the WEST tokamak
- 15 March 2022
- Published by IOP Publishing in Nuclear Fusion
- Vol. 62 (5) , 056010
First plasma exposure of a pre-damaged ITER-like plasma-facing unit in the WEST tokamak: procedure for the PFU preparation and lessons learned
The evaluation of the impact of plasma-facing components damage on subsequent plasma operation is an important issue for ITER. During the first phase of the operation of WEST, a few ITER-like divertor plasma-facing units (PFUs) have been installed on the lower divertor. One PFU was pre-damaged under electron beam gun thermal loading, before its installation in WEST, and the subsequent evolution of the damage was studied after the WEST plasma exposure. This paper presents the procedure followed to get the pre-damaged PFU. It consists of the characterization of the response of tungsten samples representative of WEST PFU under high heat flux (HHF) loading, the selection of damage (namely, small cracks, crack network, crack network, and W melt droplets). Finally, according to the WEST plasma loading conditions, the blocks with damage within the PFU and the position of the pre-damaged PFU on the WEST lower divertor are attributed. The first results obtained after an initial plasma exposure in WEST lead to the assessment, as expected with regard to the heat loading conditions, that no major surface aspect modification was found. This result emphasized the possibility of implementing as pre-damaged small droplets of melted tungsten in a high heat-loaded zone for a future WEST experimental campaign.
- 15 March 2022
- Published by IOP Publishing in Nuclear Fusion
- Vol. 62 (5) , 056010
First plasma exposure of a pre-damaged ITER-like plasma-facing unit in the WEST tokamak: procedure for the PFU preparation and lessons learned
The evaluation of the impact of plasma-facing components damage on subsequent plasma operation is an important issue for ITER. During the first phase of the operation of WEST, a few ITER-like divertor plasma-facing units (PFUs) have been installed on the lower divertor. One PFU was pre-damaged under electron beam gun thermal loading, before its installation in WEST, and the subsequent evolution of the damage was studied after the WEST plasma exposure. This paper presents the procedure followed to get the pre-damaged PFU. It consists of the characterization of the response of tungsten samples representative of WEST PFU under high heat flux (HHF) loading, the selection of damage (namely, small cracks, crack network, crack network, and W melt droplets). Finally, according to the WEST plasma loading conditions, the blocks with damage within the PFU and the position of the pre-damaged PFU on the WEST lower divertor are attributed. The first results obtained after an initial plasma exposure in WEST lead to the assessment, as expected with regard to the heat loading conditions, that no major surface aspect modification was found. This result emphasized the possibility of implementing as pre-damaged small droplets of melted tungsten in a high heat-loaded zone for a future WEST experimental campaign.
- Open Access
- 20 February 2022
- Published by Elsevier in Fusion Engineering and Design
- Vol. 177
Integrated design strategy for EU-DEMO first wall protection from plasma transients
- 20 February 2022
- Published by Elsevier in Fusion Engineering and Design
- Vol. 177
Open AccessIntegrated design strategy for EU-DEMO first wall protection from plasma transients