Shaohong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shaohong Li has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Huarong Qi
3 shared publicationsJun Li
3 shared publicationsJunxuan Zhang
School of Materials Science and Engineering, Kunming University of Science and Technology, Kunming, People's Republic of China
3 shared publications- Mengnie Li
Faculty of Materials Science and Engineering, Yunnan Key Laboratory of Integrated Computational Materials Engineering for Light Alloys, Kunming University of Science and Technology, Kunming, China
3 shared publications Dong-Hui Li
School of Materials Science and Engineering, Kunming University of Science and Technology, Kunming, China
2 shared publicationsDonghui Li
Faculty of Material Science and Engineering Kunming University of Science and Technology Kunming Yunnan 650093 China
2 shared publications
Latest Publications
- Open Access
- 22 May 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 42, 10656-10676
Synergistic effects of quenching and partitioning on the microstructural evolution and thermal fatigue behavior of H13 hot-work tool steel
- 22 May 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 42, 10656-10676
Open AccessSynergistic effects of quenching and partitioning on the microstructural evolution and thermal fatigue behavior of H13 hot-work tool steel
- Open Access
- 1 January 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 34, 2740-2753
Microstructure evolution and mechanical properties degradation behavior of nuclear power pressure vessel steel induced by prolonged thermal aging
- 1 January 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 34, 2740-2753
Open AccessMicrostructure evolution and mechanical properties degradation behavior of nuclear power pressure vessel steel induced by prolonged thermal aging
- 1 April 2024
- Published by Wiley in Steel Research International
- Vol. 95 (6)
Design of Heterogeneous Lamella Microstructure of 316L Austenitic Stainless Steel and Effect of Aging on Its Mechanical Behavior and Corrosion Properties
316L austenitic stainless steel (ASS) with a heterogeneous structure exhibits favorable mechanical properties at room temperature, promising excellent application potential. However, the thermal stability of 316L ASS with heterogeneous lamella structure (HLS) has not been adequately addressed yet. Herein, an HLS of 316L ASS is fabricated through 78% cold rolling followed by annealing at 750 °C for 13 min. The detailed investigation focuses on the influence of microstructure evolution on the mechanical properties and corrosion resistance of the alloy after aging at temperatures ranging from 350 to 550 °C for 100 h. The results show that a notable quantity of residual martensite persists even after annealing at high temperatures for a brief duration. The dislocation density of the test steel is reduced after long‐term aging treatment, and the residual martensite is further reversed into austenite during aging. In addition, the aging treatment also promotes further growth of nanocrystalline/ultrafine‐grained, which weakens the heterogeneous characteristics of HLS 316L ASS, resulting in a slight decrease in mechanical properties. However, the decrease in defect density and the enhancement of recrystallization degree are beneficial for eliminating most of the corrosion‐sensitive areas in the cold‐deformed structure, thereby improving the corrosion resistance.
- 1 April 2024
- Published by Wiley in Steel Research International
- Vol. 95 (6)
Design of Heterogeneous Lamella Microstructure of 316L Austenitic Stainless Steel and Effect of Aging on Its Mechanical Behavior and Corrosion Properties
316L austenitic stainless steel (ASS) with a heterogeneous structure exhibits favorable mechanical properties at room temperature, promising excellent application potential. However, the thermal stability of 316L ASS with heterogeneous lamella structure (HLS) has not been adequately addressed yet. Herein, an HLS of 316L ASS is fabricated through 78% cold rolling followed by annealing at 750 °C for 13 min. The detailed investigation focuses on the influence of microstructure evolution on the mechanical properties and corrosion resistance of the alloy after aging at temperatures ranging from 350 to 550 °C for 100 h. The results show that a notable quantity of residual martensite persists even after annealing at high temperatures for a brief duration. The dislocation density of the test steel is reduced after long‐term aging treatment, and the residual martensite is further reversed into austenite during aging. In addition, the aging treatment also promotes further growth of nanocrystalline/ultrafine‐grained, which weakens the heterogeneous characteristics of HLS 316L ASS, resulting in a slight decrease in mechanical properties. However, the decrease in defect density and the enhancement of recrystallization degree are beneficial for eliminating most of the corrosion‐sensitive areas in the cold‐deformed structure, thereby improving the corrosion resistance.
- 1 May 2023
- Published by SAGE Publications in Materials Science and Technology
- Vol. 39 (8) , 994-1009
Thermomechanical behaviour modelling and microstructure evolution of high Cr–Co–Mo aerospace bearing steel
The microstructure evolution and hot-compressive behaviour of high Cr–Co–Mo bearing steel under different deformation conditions were investigated by dynamic recrystallisation (DRX) kinetics analysis and simulation. The results showed that the thermal deformation parameters and carbide dissolution have a great influence on the rheological properties and microstructure. The flow stress decreases with the increase of temperature and the decrease of strain rate. The grain boundary pinning effect is weakened by the dissolution of carbides into the matrix, resulting in the rapid growth of DRX grains. The processing map of high Cr–Co–Mo bearing steel was divided into five regions, and the most suitable processing parameters can be defined as the temperature range of 1000–1070°C and strain rate range of 0.01–0.003 s−1.
- 1 May 2023
- Published by SAGE Publications in Materials Science and Technology
- Vol. 39 (8) , 994-1009
Thermomechanical behaviour modelling and microstructure evolution of high Cr–Co–Mo aerospace bearing steel
The microstructure evolution and hot-compressive behaviour of high Cr–Co–Mo bearing steel under different deformation conditions were investigated by dynamic recrystallisation (DRX) kinetics analysis and simulation. The results showed that the thermal deformation parameters and carbide dissolution have a great influence on the rheological properties and microstructure. The flow stress decreases with the increase of temperature and the decrease of strain rate. The grain boundary pinning effect is weakened by the dissolution of carbides into the matrix, resulting in the rapid growth of DRX grains. The processing map of high Cr–Co–Mo bearing steel was divided into five regions, and the most suitable processing parameters can be defined as the temperature range of 1000–1070°C and strain rate range of 0.01–0.003 s−1.
- 3 March 2023
- Published by Wiley in Steel Research International
- Vol. 94 (7)
A Novel Heat Treatment Strategy Based on Quenching and Carbides Preprecipitation and Subsequent Critical Quenching to Improve the Thermal Fatigue Performance of AISI H13 Tool Steel
The effects of conventional quenching and based on quenching and carbides preprecipitation and subsequent critical quenching (QPQ) processes on the microstructure evolution, thermal stability and thermal fatigue are studied for H13 tool steel. The results show that the QPQ treatment is beneficial to precipitate smaller and more uniformly distributed carbides during the tempering. According to the analysis of microstructure and mechanical properties, it is found that the tempering after QPQ treatment can refine the grain size of the steel by about 60% and can increase the impact toughness by 34.8%. Moreover, it is also found that the activation energy required by the QPQ treatment is higher than that of the conventional quenched samples for long‐time tempering, which is mainly related to the coarsening and accumulation of carbides. According to the statistical analysis results of average thermal fatigue crack length, crack density, and surface hardness, the improvement of thermal fatigue performance of the QPQ treatment after tempering is mainly attributed to the uniform fine carbide and grain refinement, which passivates the crack tip and improves the service life to a certain extent.
- 3 March 2023
- Published by Wiley in Steel Research International
- Vol. 94 (7)
A Novel Heat Treatment Strategy Based on Quenching and Carbides Preprecipitation and Subsequent Critical Quenching to Improve the Thermal Fatigue Performance of AISI H13 Tool Steel
The effects of conventional quenching and based on quenching and carbides preprecipitation and subsequent critical quenching (QPQ) processes on the microstructure evolution, thermal stability and thermal fatigue are studied for H13 tool steel. The results show that the QPQ treatment is beneficial to precipitate smaller and more uniformly distributed carbides during the tempering. According to the analysis of microstructure and mechanical properties, it is found that the tempering after QPQ treatment can refine the grain size of the steel by about 60% and can increase the impact toughness by 34.8%. Moreover, it is also found that the activation energy required by the QPQ treatment is higher than that of the conventional quenched samples for long‐time tempering, which is mainly related to the coarsening and accumulation of carbides. According to the statistical analysis results of average thermal fatigue crack length, crack density, and surface hardness, the improvement of thermal fatigue performance of the QPQ treatment after tempering is mainly attributed to the uniform fine carbide and grain refinement, which passivates the crack tip and improves the service life to a certain extent.
- 29 May 2022
- Published by Wiley in Steel Research International
- Vol. 93 (9)
Influence of Deep Cryogenic Treatment on Microstructural Evolution and Transformation Kinetics Simulation by Finite Element Method of Low‐Carbon High‐Alloy Martensitic‐Bearing Steel
Nowadays, deep cryogenic treatment (DCT) is taken as a promising technique for improving the performance of steel. This article is focused on the influence of different heat treatment processes involving DCT on the microstructural evolution of a high Cr–Co–Mo high‐temperature‐bearing steel. Moreover, a multiphysical field coupling numerical model is built to investigate the martensitic transformation kinetics during DCT. The results show that DCT significantly improves the hardness and promotes the transformation of retained austenite to martensite at low temperatures. DCT not only refines the retained austenite as thin‐film morphology but also increases the precipitation of carbides and induces the carbides more homogenous distribution. This indicates that DCT promoted the segregation of carbon atoms and reduced the carbon content of martensite. The finite element model simulation shows that the retained austenite transformation is still incomplete, and the simulation results agree well with the experimental data by X‐Ray diffraction and transmission electron microscope analysis. This implies that the finite element simulation can better reflect and verify the experimental results.
- 29 May 2022
- Published by Wiley in Steel Research International
- Vol. 93 (9)
Influence of Deep Cryogenic Treatment on Microstructural Evolution and Transformation Kinetics Simulation by Finite Element Method of Low‐Carbon High‐Alloy Martensitic‐Bearing Steel
Nowadays, deep cryogenic treatment (DCT) is taken as a promising technique for improving the performance of steel. This article is focused on the influence of different heat treatment processes involving DCT on the microstructural evolution of a high Cr–Co–Mo high‐temperature‐bearing steel. Moreover, a multiphysical field coupling numerical model is built to investigate the martensitic transformation kinetics during DCT. The results show that DCT significantly improves the hardness and promotes the transformation of retained austenite to martensite at low temperatures. DCT not only refines the retained austenite as thin‐film morphology but also increases the precipitation of carbides and induces the carbides more homogenous distribution. This indicates that DCT promoted the segregation of carbon atoms and reduced the carbon content of martensite. The finite element model simulation shows that the retained austenite transformation is still incomplete, and the simulation results agree well with the experimental data by X‐Ray diffraction and transmission electron microscope analysis. This implies that the finite element simulation can better reflect and verify the experimental results.
- 7 June 2019
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 26 (10) , 1096-1105
Carbides precipitation and their evolution of Cr15Co10Mo5-alloyed heat-resistant bearing steel after tempering at different temperatures
- 7 June 2019
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 26 (10) , 1096-1105
Carbides precipitation and their evolution of Cr15Co10Mo5-alloyed heat-resistant bearing steel after tempering at different temperatures
- 28 March 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (7) , 076531
Effect of stresses on martensite transformation kinetics and transformation plasticity of S34MnV steel
Expansions of martensite transformation in S34MnV steel are studied under tensile and compressive stresses using a Gleeble-3500 thermo-mechanical simulation system. Coupled analyses of the experimental data are conducted to simultaneously determine the kinetic parameters in the Koistinen-Marburger equation and the transformation plasticity coefficient in the Greenwood-Johnson model of martensite transformation. Such components as elastic strain, thermal strain and transformation strain are extracted from the total strain so as to determine the transformation plasticity strain under various loads. Transformation plasticity data are fit into the Greenwood-Johnson model to obtain the transformation plasticity coefficient K. Transformation plasticity coefficient K in the Greenwood-Johnson model has a constant value under tensile stresses and another lower value under compressive stresses. Effects of applied stresses on kinetic parameters α and Ms in the Koistinen-Marburger model are evaluated but found insignificant.
- 28 March 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (7) , 076531
Effect of stresses on martensite transformation kinetics and transformation plasticity of S34MnV steel
Expansions of martensite transformation in S34MnV steel are studied under tensile and compressive stresses using a Gleeble-3500 thermo-mechanical simulation system. Coupled analyses of the experimental data are conducted to simultaneously determine the kinetic parameters in the Koistinen-Marburger equation and the transformation plasticity coefficient in the Greenwood-Johnson model of martensite transformation. Such components as elastic strain, thermal strain and transformation strain are extracted from the total strain so as to determine the transformation plasticity strain under various loads. Transformation plasticity data are fit into the Greenwood-Johnson model to obtain the transformation plasticity coefficient K. Transformation plasticity coefficient K in the Greenwood-Johnson model has a constant value under tensile stresses and another lower value under compressive stresses. Effects of applied stresses on kinetic parameters α and Ms in the Koistinen-Marburger model are evaluated but found insignificant.
- 1 September 2018
- Published by Elsevier in Biomedicine & Pharmacotherapy
- Vol. 105, 582-589
MicroRNA-873 acts as a tumor suppressor in esophageal cancer by inhibiting differentiated embryonic chondrocyte expressed gene 2
- 1 September 2018
- Published by Elsevier in Biomedicine & Pharmacotherapy
- Vol. 105, 582-589
MicroRNA-873 acts as a tumor suppressor in esophageal cancer by inhibiting differentiated embryonic chondrocyte expressed gene 2