Gerard Guillamet
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gerard Guillamet has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Albert Turon
University of Girona, Girona, Spain
6 shared publications J. Costa
3 shared publications- Joan Andreu Mayugo
University of Girona
3 shared publications - Pere Maimi
University of Girona-AMADE
3 shared publications - Adria Quintanas Corominas
Department of Computer Applications in Science and Engineering, Barcelona Supercomputing Centre (BSC)
2 shared publications - Emilio V. González
AMADE, Mechanical Engineering and Industrial Construction Department, Universitat de Girona, Girona, Spain
2 shared publications
Latest Publications
- 20 April 2023
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 43 (7-8) , 440-455
In search of the quasi-isotropic laminate with optimal delamination resistance under off-axis loads
Delamination is one of the most feared failure modes in laminated composites and yet there is a lack of well established procedures to find the ply configuration with the highest delamination resistance for a given geometry of the component and a set of elastic and strength constraints. This paper presents a methodology for determining the quasi-isotropic ply sequence more resistant to delamination under off-axis uniaxial tension. Delamination is considered to be triggered by interlaminar stresses at free-edges or by matrix cracks. Two different ply thicknesses (standard and thin) and two sets of ply orientations (multiples of π/4 or π/8) are considered. The results show that the use of thin plies enlarges the design domain by up to 70% and generates a practically isotropic safe space. The methodology presented is also suitable for optimizing the delamination resistance of other load cases with stress singularities.
- 20 April 2023
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 43 (7-8) , 440-455
In search of the quasi-isotropic laminate with optimal delamination resistance under off-axis loads
Delamination is one of the most feared failure modes in laminated composites and yet there is a lack of well established procedures to find the ply configuration with the highest delamination resistance for a given geometry of the component and a set of elastic and strength constraints. This paper presents a methodology for determining the quasi-isotropic ply sequence more resistant to delamination under off-axis uniaxial tension. Delamination is considered to be triggered by interlaminar stresses at free-edges or by matrix cracks. Two different ply thicknesses (standard and thin) and two sets of ply orientations (multiples of π/4 or π/8) are considered. The results show that the use of thin plies enlarges the design domain by up to 70% and generates a practically isotropic safe space. The methodology presented is also suitable for optimizing the delamination resistance of other load cases with stress singularities.
- 1 January 2021
- Published by Elsevier
- p. 555-577
Mesoscale modelling of delamination using the cohesive zone model approach
- 1 January 2021
- Published by Elsevier
- p. 555-577
Mesoscale modelling of delamination using the cohesive zone model approach
- 1 February 2019
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 117, 76-91
Improving damage resistance and load capacity of thin-ply laminates using ply clustering and small mismatch angles
- 1 February 2019
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 117, 76-91
Improving damage resistance and load capacity of thin-ply laminates using ply clustering and small mismatch angles
- 1 September 2018
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 71, 278-291
A 3D transversally isotropic constitutive model for advanced composites implemented in a high performance computing code
- 1 September 2018
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 71, 278-291
A 3D transversally isotropic constitutive model for advanced composites implemented in a high performance computing code
- 1 January 2018
- Published by Elsevier in Composite Structures
- Vol. 184, 506-511
Accurate simulation of delamination under mixed-mode loading using a cohesive model with a mode-dependent penalty stiffness
- 1 January 2018
- Published by Elsevier in Composite Structures
- Vol. 184, 506-511
Accurate simulation of delamination under mixed-mode loading using a cohesive model with a mode-dependent penalty stiffness
- Open Access
- 1 October 2017
- Published by Elsevier in Composites Part B: Engineering
- Vol. 126, 133-142
Experimental study into compression after impact strength of laminates with conventional and nonconventional ply orientations
- 1 October 2017
- Published by Elsevier in Composites Part B: Engineering
- Vol. 126, 133-142
Open AccessExperimental study into compression after impact strength of laminates with conventional and nonconventional ply orientations
- 1 December 2016
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 168, 28-39
A quick procedure to predict free-edge delamination in thin-ply laminates under tension
- 1 December 2016
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 168, 28-39
A quick procedure to predict free-edge delamination in thin-ply laminates under tension
- 1 June 2014
- Published by Elsevier in Composites Science and Technology
- Vol. 98, 44-50
Damage occurrence at edges of non-crimp-fabric thin-ply laminates under off-axis uniaxial loading
- 1 June 2014
- Published by Elsevier in Composites Science and Technology
- Vol. 98, 44-50
Damage occurrence at edges of non-crimp-fabric thin-ply laminates under off-axis uniaxial loading