Ramon Gonzalo

This work addresses the lack of moisture content estimation models for food products in the millimeter-wave frequency range and showcases the potential of this range for designing compact, cost-effective and in-line food moisture sensors. The moisture content estimation models developed in this study are intended for flour-based mixtures in the 67-110 GHz frequency range and are derived by means of a non-destructive and contactless monitoring system. To this aim, data obtained by continuous-wave (CW) vector network analyzer (VNA) spectroscopy is used to create two different models, both with a coefficient of determination ( R ² ) of 0.97. One model is based on the theoretical response obtained by means of the Looyenga effective medium theory (EMT) model, while the other is based on measured data. Both models have been experimentally validated with root mean square error (RMSE) values of 0.4 and 0.35% respectively. These small estimation errors show the potential of this frequency range to design compact, cost-effective and in-line food moisture sensors. This research contributes to improving quality control and monitoring of moisture levels in flour-based mixtures.

In this paper the design and experimental validation of a fourth-harmonic mixer based on Schottky diodes working around 300 GHz is presented. The main novelty of this work consists in the integration of an MMIC-based local oscillator, working around 75 GHz, and a mixer in the same metallic block housing. A prototype has been characterized using the Y-Factor method and yields a best measured conversion loss and an equivalent noise temperature of 14 dB and 9600 K, respectively. This performance is comparable to the state-of-the-art for this type of mixer.

This paper reviews the different remote sensing techniques found in the literature to monitor plant water status, allowing farmers to control the irrigation management and to avoid unnecessary periods of water shortage and a needless waste of valuable water. The scope of this paper covers a broad range of 77 references published between the years 1981 and 2021 and collected from different search web sites, especially Scopus. Among them, 74 references are research papers and the remaining three are review papers. The different collected approaches have been categorized according to the part of the plant subjected to measurement, that is, soil (12.2%), canopy (33.8%), leaves (35.1%) or trunk (18.9%). In addition to a brief summary of each study, the main monitoring technologies have been analyzed in this review. Concerning the presentation of the data, different results have been obtained. According to the year of publication, the number of published papers has increased exponentially over time, mainly due to the technological development over the last decades. The most common sensor is the radiometer, which is employed in 15 papers (20.3%), followed by continuous-wave (CW) spectroscopy (12.2%), camera (10.8%) and THz time-domain spectroscopy (TDS) (10.8%). Excluding two studies, the minimum coefficient of determination (R²) obtained in the references of this review is 0.64. This indicates the high degree of correlation between the estimated and measured data for the different technologies and monitoring methods. The five most frequent water indicators of this study are: normalized difference vegetation index (NDVI) (12.2%), backscattering coefficients (10.8%), spectral reflectance (8.1%), reflection coefficient (8.1%) and dielectric constant (8.1%).

In this paper the design and experimental characterization of a combined doubler-subharmonic mixer based on Schottky diodes which uses a 75 GHz MMIC based local oscillator is presented. This solution integrates in the same substrate the doubler and the mixer, which share the same metallic packaging with the local oscillator. The prototype has been fabricated and measured. For characterization, the Y-Factor technique has been used and the prototype yields a best conversion loss and equivalent noise temperature of 11 dB and 1976 K, respectively, at 305 GHz. This performance is close to the state of the art, and shows the potential of this approach, which allows a significant reduction in terms of size and volume.

This paper presents a planar silicon integrated subharmonic mixer on top of a photonic-crystal platform. The local oscillator (LO) power is injected through a 2D photonic-crystal (PC) slab to a resonant cavity that effectively couples the signal to a planar bow-tie antenna. The same antenna, which is printed on the top of the PC cavity, contains an antiparallel Schottky diode pair which performs the down-conversion. The proposed design is a single layer, low cost, low profile device. Moreover, the described fabrication process is compatible with active components integration. The performance of the design has been experimentally demonstrated showing good agreement with the simulation and is comparable with the state-of-the-art of planar mixers. The work presented here is based on concepts and technologies from electronics and photonics domains and may be a good starting point for the creation of new devices, allowing the integration and upgrading of existing techniques from both worlds.

In this paper two different simple to design and easy to manufacturing transitions from a microstrip to rectangular waveguide based on ridge and groove gap waveguides are studied. The first one is based on a combination of a groove and ridge gap waveguide. In this case, the microstrip substrate occupies the whole bottom metallic housing block, namely, the transition and the gap between the bed of nails and the lid; therefore, it does not require any substrate shaping. Nevertheless, the transition needs to replace groove waveguide by ridge gap waveguide sections to avoid higher-order mode excitation. In the second approach, based on only a groove gap waveguide, the substrate is shaped to be only in the microstrip section, that is, outside the bed of nails area. This leads to a simplification of the design procedure. Prototypes of both transitions have been characterized, showing good agreement with the simulations taking into account the manufacturing tolerances. Performance comparable to the state-of-the-art in this frequency band has been achieved.

In this paper a comparison between a fourth harmonic mixer and a combined doubler/subharmonic mixer based on Schottky diodes working at 300 GHz with MMIC Local Oscillator (LO) integrated in a single enclosing is presented. Both configurations allow reducing the LO requirements, since a lower LO frequency is used. In addition, the integration of the MMIC Local Oscillator with the mixer in the same single metallic block is the main novelty and advantage of this work. Since only one block is used, flange connections are avoided. This way, misalignment errors are also prevented. Besides this advantage, the compactness of this solution is also remarkable, leading to a significant weight reduction.

THz communications systems at carrier frequencies above 200 GHz are the key to enable next-generation mobile communication networks with 100 Gbit/s wireless data rates. One of the key questions is, which carrier frequency generation technique will be the most suitable. This is currently addressed by two separate approaches, electronics-based and photonics-based. We present in this paper a truly microwave photonic approach that benefits from the main key features of each, bandwidth, tunability, stability and fiber compatibility from photonics and power handling capability from the electronics. It is based on a Photonic Local Oscillator (PLO), generating a 100 GHz frequency, fed into an electronic frequency multiplier. A high speed uni-travelling carrier photodiode (UTC-PD) provides the 100 GHz PLO for Schottky tripler diodes, generating 300 GHz signal. To feed the UTC-PD, we present a photonic integrated mode locked laser source. According to the simulations and measurements, the developed transmitter can produce a maximum of 12 μW of THz power at 280 GHz.