László Péter Kollár
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
László Péter Kollár has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
George S. Springer
Department of Aeronautics and Astronautics, William F. Durand Building, Stanford University, Stanford, CA 94305
7 shared publicationsGabriella Tarján
6 shared publications- Tamás Ther
Department of Mechanics, Materials and Structures, Budapest University of Technology and Economics, Budapest, Hungary
5 shared publications Helmut Krawinkler
Department of Civil Engineering, Stanford University, Stanford, CA, USA
4 shared publicationsJohn Jai
Department of Aeronautics and Astronautics, Stanford University, Stanford, CA, USA
4 shared publications- George S. Springer
Stanford University, California
3 shared publications
Latest Publications
- 26 April 2022
- Published by Taylor & Francis
- p. 3-7
Design and fabrication of the reticulated tubular dome structure of a sports hall in Budapest
A sports hall on an elliptic ground plan of 96×64 m will be covered by a reticulated tubular shell structure having the form of an elliptic paraboloid. The columns of the dome structure are also tubes. The paper outlines the development of the structure and some problems in the static analysis, describes the fabrication process, and shows some structural details.
- 26 April 2022
- Published by Taylor & Francis
- p. 3-7
Design and fabrication of the reticulated tubular dome structure of a sports hall in Budapest
A sports hall on an elliptic ground plan of 96×64 m will be covered by a reticulated tubular shell structure having the form of an elliptic paraboloid. The columns of the dome structure are also tubes. The paper outlines the development of the structure and some problems in the static analysis, describes the fabrication process, and shows some structural details.
- Open Access
- 10 April 2021
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 104 (3) , 2099-2116
Dynamical similarity of multi-block catenary arches and rocking blocks subjected to horizontal base excitation
In this paper, the dynamical similarity of multi-block catenary arches and columns is discussed, which can be used for the simplified design of rocking arches. The basic hypothesis is that the dynamic response of multi-block arches and columns is similar when the shape of the arch follows the thrust line, i.e. it is a catenary arch. It is validated numerically that the responses of slender catenary arches are safe and reliable approximations of those of not slender arches and then that the overturning acceleration (response) spectra of rigid, slender monolithic blocks can be directly applied for catenary arches. The similarity is based on two parameters, on the limit peak ground acceleration (under which the structure will not move at all) and on the frequency parameter (defined by Housner for rigid blocks).
- 10 April 2021
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 104 (3) , 2099-2116
Open AccessDynamical similarity of multi-block catenary arches and rocking blocks subjected to horizontal base excitation
In this paper, the dynamical similarity of multi-block catenary arches and columns is discussed, which can be used for the simplified design of rocking arches. The basic hypothesis is that the dynamic response of multi-block arches and columns is similar when the shape of the arch follows the thrust line, i.e. it is a catenary arch. It is validated numerically that the responses of slender catenary arches are safe and reliable approximations of those of not slender arches and then that the overturning acceleration (response) spectra of rigid, slender monolithic blocks can be directly applied for catenary arches. The similarity is based on two parameters, on the limit peak ground acceleration (under which the structure will not move at all) and on the frequency parameter (defined by Housner for rigid blocks).
- 10 December 2019
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Civil Engineering
- Vol. 63 (4) , 1204-1216
Model of Soil-structure Interaction of Objects Resting on Finite Depth Soil Layers for Seismic Design
In case of seismic design of structures the deformability and damping of the soil should be considered, which can be performed in several ways. The infinite soil half space can be approximated with the cone model, which gives constant values for the spring stiffnesses and dashpot characteristics, and an additional mass element for rocking motion. To approximate the dynamic impedance function of a soil layer more complex models were also applied. Most of the methods do not take into account the finite dimensions of the soil, which results significantly different behavior than spring-dashpot systems. To consider the effect of a finite layer a new simple model based on a physical approach is given for the horizontal excitation of strip foundations. Numerical verification is presented, and the parameter range is determined, where the application of the new model is recommended, since applying a spring-dashpot model results in significant errors.
- 10 December 2019
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Civil Engineering
- Vol. 63 (4) , 1204-1216
Model of Soil-structure Interaction of Objects Resting on Finite Depth Soil Layers for Seismic Design
In case of seismic design of structures the deformability and damping of the soil should be considered, which can be performed in several ways. The infinite soil half space can be approximated with the cone model, which gives constant values for the spring stiffnesses and dashpot characteristics, and an additional mass element for rocking motion. To approximate the dynamic impedance function of a soil layer more complex models were also applied. Most of the methods do not take into account the finite dimensions of the soil, which results significantly different behavior than spring-dashpot systems. To consider the effect of a finite layer a new simple model based on a physical approach is given for the horizontal excitation of strip foundations. Numerical verification is presented, and the parameter range is determined, where the application of the new model is recommended, since applying a spring-dashpot model results in significant errors.
- Open Access
Dynamic Response of Long Rectangular Floors Subjected to Periodic Force Excitation
Since damping in lightweight floors is usually low, dynamic amplification can be rather high. Long rectangular plates subjected to concentrated loads are often investigated by a replacement beam with a so called “effective width”. Although this approach is a reliable tool for static loads, the steady-state dynamic response of beams and long plates subjected to periodic loads are significantly different. The maximum displacements and accelerations of beams (and of not-long rectangular plates) are obtained by using a dynamic amplification factor, which in the case of resonance is equal to , where is the damping ratio. For long plates (and for not-long orthotropic rib-stiffened plates), as discussed in the paper, the response and the amplification factor are substantially different from those of beams. Hence, design based on effective width may lead to 2–4 times higher acceleration than the real values. In an economic design, to avoid unnecessary damping enhancement, this effect must be taken into account.Open AccessDynamic Response of Long Rectangular Floors Subjected to Periodic Force Excitation
Since damping in lightweight floors is usually low, dynamic amplification can be rather high. Long rectangular plates subjected to concentrated loads are often investigated by a replacement beam with a so called “effective width”. Although this approach is a reliable tool for static loads, the steady-state dynamic response of beams and long plates subjected to periodic loads are significantly different. The maximum displacements and accelerations of beams (and of not-long rectangular plates) are obtained by using a dynamic amplification factor, which in the case of resonance is equal to , where is the damping ratio. For long plates (and for not-long orthotropic rib-stiffened plates), as discussed in the paper, the response and the amplification factor are substantially different from those of beams. Hence, design based on effective width may lead to 2–4 times higher acceleration than the real values. In an economic design, to avoid unnecessary damping enhancement, this effect must be taken into account. - Open Access
- 12 March 2019
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 48 (7) , 709-730
Numerical model and dynamic analysis of multi degree of freedom masonry arches
Summary: A new model is presented for planar multi‐block arches subjected to earthquakes. The blocks are assumed to be rigid, and every interface between the blocks may split open and may close, ie, the blocks may impact to each other. During impact, both the classical Housner's approach and improved models with lower energy dissipation are considered. The arch model is verified by comparisons with the available results in the literature. Using the new model, it was found that the circular arch moves as a four‐hinge mechanism typically only at the beginning of excitation, and several cracks split open during motion; furthermore, that modeling a multi‐block arch by a single degree of freedom (SDOF) four‐hinge mechanism may significantly overestimate its collapse load. While, in accordance with the literature, the overturning curves of single blocks and arches with symmetrically located four hinges are similar; for multi‐block arches where several hinges may occur they can be very different.
- 12 March 2019
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 48 (7) , 709-730
Open AccessNumerical model and dynamic analysis of multi degree of freedom masonry arches
Summary: A new model is presented for planar multi‐block arches subjected to earthquakes. The blocks are assumed to be rigid, and every interface between the blocks may split open and may close, ie, the blocks may impact to each other. During impact, both the classical Housner's approach and improved models with lower energy dissipation are considered. The arch model is verified by comparisons with the available results in the literature. Using the new model, it was found that the circular arch moves as a four‐hinge mechanism typically only at the beginning of excitation, and several cracks split open during motion; furthermore, that modeling a multi‐block arch by a single degree of freedom (SDOF) four‐hinge mechanism may significantly overestimate its collapse load. While, in accordance with the literature, the overturning curves of single blocks and arches with symmetrically located four hinges are similar; for multi‐block arches where several hinges may occur they can be very different.
- 3 October 2017
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 16 (3) , 1607-1631
Overturning of rigid blocks for earthquake excitation
- 3 October 2017
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 16 (3) , 1607-1631
Overturning of rigid blocks for earthquake excitation
- 21 September 2017
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 47 (2) , 418-437
Model for multiblock columns subjected to base excitation
Summary: A new model is presented for multiblock columns subjected to earthquakes, which contains an impact and an opening model. Both in the impact and in the opening model, all the possible opening configurations are investigated because it was found that in many practical cases, unexpected patterns may occur. The model is purely mechanical: assuming rigid blocks and classical (inelastic) impact. The effect of energy dissipation during impact was investigated. Using our model in accordance with the literature, it was found that monolithic blocks are more vulnerable to overturning than multiblock systems.
- 21 September 2017
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 47 (2) , 418-437
Model for multiblock columns subjected to base excitation
Summary: A new model is presented for multiblock columns subjected to earthquakes, which contains an impact and an opening model. Both in the impact and in the opening model, all the possible opening configurations are investigated because it was found that in many practical cases, unexpected patterns may occur. The model is purely mechanical: assuming rigid blocks and classical (inelastic) impact. The effect of energy dissipation during impact was investigated. Using our model in accordance with the literature, it was found that monolithic blocks are more vulnerable to overturning than multiblock systems.
- 18 November 2016
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 15 (5) , 2305-2319
Refinement of Housner’s model on rocking blocks
- 18 November 2016
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 15 (5) , 2305-2319
Refinement of Housner’s model on rocking blocks
- 28 August 2015
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 34 (22) , 1884-1901
Local buckling of composite beams with edge-stiffened flanges subjected to axial load
Local buckling analysis of thin walled composite beams is presented, where the flanges are stiffened at their free edges. The web and the flanges are modelled by rotationally restrained long orthotropic plates. Explicit expressions are developed for the calculation of the lowest buckling load. For the stability of the flange distortional buckling, plate buckling (or local buckling) and their interaction are considered, while the stabilizing effect of the web is taken into account by elastic constraint. Web buckling is modelled with a long plate, whose edges are constrained by stiffeners with warping stiffness. The accuracy of the method is demonstrated through numerical examples.
- 28 August 2015
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 34 (22) , 1884-1901
Local buckling of composite beams with edge-stiffened flanges subjected to axial load
Local buckling analysis of thin walled composite beams is presented, where the flanges are stiffened at their free edges. The web and the flanges are modelled by rotationally restrained long orthotropic plates. Explicit expressions are developed for the calculation of the lowest buckling load. For the stability of the flange distortional buckling, plate buckling (or local buckling) and their interaction are considered, while the stabilizing effect of the web is taken into account by elastic constraint. Web buckling is modelled with a long plate, whose edges are constrained by stiffeners with warping stiffness. The accuracy of the method is demonstrated through numerical examples.