Andrew P. S. Wheeler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrew P. S. Wheeler has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
Jonathan Ong
GE Global Research, Munich 85748, Germany
4 shared publications- Richard D. Sandberg
Department of Mechanical Engineering, University of Melbourne, Parkville, VIC 3010, Australia
4 shared publications Li He
3 shared publicationsRobert J. Miller
Whittle Laboratory, University of Cambridge, Cambridge CB3 0DY, United Kingdom
3 shared publications- Francesco Tosto
Propulsion and Power, Delft University of Technology, Kluyverweg 1, 2629 HS Delft, The Nethelands
2 shared publications - Matteo Pini
Propulsion & Power, Faculty of Aerospace Engineering, Delft University of Technology, 2628 CD Delft, The Netherlands
2 shared publications
Latest Publications
- Open Access
- 1 June 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (6)
Non-ideal fluid turbulent boundary layers in supercritical carbon dioxide compressor cascades: A high-fidelity simulation study near the critical point
This paper presents one of the first high-fidelity numerical investigations of supercritical carbon dioxide (sCO2) turbulent boundary layers in a compressor cascade, conducted without turbulence modeling to ensure physical consistency and capture the intrinsic flow physics near the critical point. This work clarifies the turbulent boundary-layer development and loss characteristics of sCO2 in compressor cascades, establishing a foundation and a benchmark case for turbulence-model validation and future turbomachinery design in non-ideal compressible flow regimes. Comparative simulations with air are performed under matched inlet conditions (Mach number, Reynolds number, and inflow turbulence) to investigate the influence of non-ideal fluid properties on boundary layer development, flow separation, and aerodynamic losses. The results reveal that due to local high Reynolds number, sCO2 exhibits earlier transition and reattachment on the suction side, while air develops a wider separated region and stronger wake losses. This results in the sCO2 case exhibits a higher pressure ratio and greater average turning angles across the cascade when compared to air. The temperature variation, on the other hand, is smaller for sCO2 due to its higher Eckert number. Many findings from the turbulent boundary layer literature are confirmed in this paper. In addition, a liquid-like viscosity variation is observed within the sCO2 boundary layers, consistent with dense-vapor behavior reported in previous studies. The inner-layer scaling of the turbulent boundary layer is also verified in the cascade configuration.
- 1 June 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (6)
Open AccessNon-ideal fluid turbulent boundary layers in supercritical carbon dioxide compressor cascades: A high-fidelity simulation study near the critical point
This paper presents one of the first high-fidelity numerical investigations of supercritical carbon dioxide (sCO2) turbulent boundary layers in a compressor cascade, conducted without turbulence modeling to ensure physical consistency and capture the intrinsic flow physics near the critical point. This work clarifies the turbulent boundary-layer development and loss characteristics of sCO2 in compressor cascades, establishing a foundation and a benchmark case for turbulence-model validation and future turbomachinery design in non-ideal compressible flow regimes. Comparative simulations with air are performed under matched inlet conditions (Mach number, Reynolds number, and inflow turbulence) to investigate the influence of non-ideal fluid properties on boundary layer development, flow separation, and aerodynamic losses. The results reveal that due to local high Reynolds number, sCO2 exhibits earlier transition and reattachment on the suction side, while air develops a wider separated region and stronger wake losses. This results in the sCO2 case exhibits a higher pressure ratio and greater average turning angles across the cascade when compared to air. The temperature variation, on the other hand, is smaller for sCO2 due to its higher Eckert number. Many findings from the turbulent boundary layer literature are confirmed in this paper. In addition, a liquid-like viscosity variation is observed within the sCO2 boundary layers, consistent with dense-vapor behavior reported in previous studies. The inner-layer scaling of the turbulent boundary layer is also verified in the cascade configuration.
- 15 October 2025
- Published by Springer Nature
- p. 81-95
Direct Simulations of Non-Ideal Supersonic Flows in the Trailing Edge Region
- 15 October 2025
- Published by Springer Nature
- p. 81-95
Direct Simulations of Non-Ideal Supersonic Flows in the Trailing Edge Region
- Open Access
Non-Equilibrium Phase Changes in Aircraft Exhaust: A Computational Study on Early Contrail Formation
A numerical framework is developed to model contrail formation in the near-field exhaust of aircraft engines, resolving non-equilibrium phase transitions in compressible, multi-component, non-ideal fluid flows. The approach combines well-established methods from steam turbine modeling for liquid-phase transitions with cloud microphysics models for ice formation. It resolves homogeneous and heterogeneous nucleation, interphase momentum exchange, and polydispersed size distributions of droplets, ice crystals, and soot particles. These models are implemented in a parallelized finite-volume solver and applied to a high-bypass turbofan exhaust configuration with simplified geometry. Results indicate that non-equilibrium effects strongly influence condensation and freezing dynamics, while nozzle geometry and water vapor content modulate local supersaturation and phase transition pathways. The findings underscore the limitations of equilibrium-based models and highlight the value of physics-based, scalable tools for analyzing contrail formation across fuels and propulsion systems.
Open AccessNon-Equilibrium Phase Changes in Aircraft Exhaust: A Computational Study on Early Contrail Formation
A numerical framework is developed to model contrail formation in the near-field exhaust of aircraft engines, resolving non-equilibrium phase transitions in compressible, multi-component, non-ideal fluid flows. The approach combines well-established methods from steam turbine modeling for liquid-phase transitions with cloud microphysics models for ice formation. It resolves homogeneous and heterogeneous nucleation, interphase momentum exchange, and polydispersed size distributions of droplets, ice crystals, and soot particles. These models are implemented in a parallelized finite-volume solver and applied to a high-bypass turbofan exhaust configuration with simplified geometry. Results indicate that non-equilibrium effects strongly influence condensation and freezing dynamics, while nozzle geometry and water vapor content modulate local supersaturation and phase transition pathways. The findings underscore the limitations of equilibrium-based models and highlight the value of physics-based, scalable tools for analyzing contrail formation across fuels and propulsion systems.
- Open Access
- 8 May 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (10) , 1-15
The Role of Turbulence Transport in Mechanical Energy Budgets
In this article, we study the role of turbulence transport on loss prediction using high fidelity scale-resolving simulations. For this purpose, we use eight high-fidelity simulation datasets and compute flux of entropy and stagnation pressure transport equation budgets for all the cases. We find that under certain unsteady inflow conditions, the stagnation pressure coefficient is not a reliable loss metric even at low Mach number conditions. This is due to the turbulence transport terms. The impact of these terms, typically assumed to be negligible, made stagnation pressure loss coefficient underpredict loss from 0% to over 40% when compared to entropy loss coefficient for cases considered here. This effect was most pronounced for the cases with highly unsteady inflow conditions and at low Reynolds numbers.
- 8 May 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (10) , 1-15
Open AccessThe Role of Turbulence Transport in Mechanical Energy Budgets
In this article, we study the role of turbulence transport on loss prediction using high fidelity scale-resolving simulations. For this purpose, we use eight high-fidelity simulation datasets and compute flux of entropy and stagnation pressure transport equation budgets for all the cases. We find that under certain unsteady inflow conditions, the stagnation pressure coefficient is not a reliable loss metric even at low Mach number conditions. This is due to the turbulence transport terms. The impact of these terms, typically assumed to be negligible, made stagnation pressure loss coefficient underpredict loss from 0% to over 40% when compared to entropy loss coefficient for cases considered here. This effect was most pronounced for the cases with highly unsteady inflow conditions and at low Reynolds numbers.
- Open Access
- 1 January 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (1)
Investigation of non-ideal effects in compressible boundary layers of dense vapors through direct numerical simulations
In this work, we present an investigation about the sources of dissipation in adiabatic boundary layers of non-ideal compressible fluid flows. Direct numerical simulations (DNS) of transitional, zero-pressure gradient boundary layer flows are performed for two fluids characterized by different complexity of the fluid molecules, namely, “air” and siloxane MM. Different sets of thermodynamic free-stream boundary conditions are selected to evaluate the influence of the fluid state on both the frictional loss and the dissipation mechanisms. The thermophysical properties of siloxane MM are calculated with a state-of-the-art equation of state. Results show that the dissipation due to both time-mean strain field, irreversible heat transfer, and turbulent dissipation differs significantly depending on both the molecular complexity of the fluid and its thermodynamic state. The dissipation coefficient calculated from the DNS results is then compared against the one obtained using a reduced-order model (ROM), which solves the two-dimensional boundary layer flow equations for an arbitrary fluid [M. Pini and C. De Servi, “Entropy generation in laminar boundary layers of non-ideal fluid flows,” in 2nd International Seminar on Non-Ideal Compressible Fluid Dynamics for Propulsion and Power (Springer, 2020), pp. 104–117]. Results from both the DNS and the ROM show that low values of the overall dissipation are observed in the case of fluids made of simple molecules, e.g., air, and if the fluid is at a thermodynamic state in the proximity of that of the vapor–liquid critical point.
- 1 January 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (1)
Open AccessInvestigation of non-ideal effects in compressible boundary layers of dense vapors through direct numerical simulations
In this work, we present an investigation about the sources of dissipation in adiabatic boundary layers of non-ideal compressible fluid flows. Direct numerical simulations (DNS) of transitional, zero-pressure gradient boundary layer flows are performed for two fluids characterized by different complexity of the fluid molecules, namely, “air” and siloxane MM. Different sets of thermodynamic free-stream boundary conditions are selected to evaluate the influence of the fluid state on both the frictional loss and the dissipation mechanisms. The thermophysical properties of siloxane MM are calculated with a state-of-the-art equation of state. Results show that the dissipation due to both time-mean strain field, irreversible heat transfer, and turbulent dissipation differs significantly depending on both the molecular complexity of the fluid and its thermodynamic state. The dissipation coefficient calculated from the DNS results is then compared against the one obtained using a reduced-order model (ROM), which solves the two-dimensional boundary layer flow equations for an arbitrary fluid [M. Pini and C. De Servi, “Entropy generation in laminar boundary layers of non-ideal fluid flows,” in 2nd International Seminar on Non-Ideal Compressible Fluid Dynamics for Propulsion and Power (Springer, 2020), pp. 104–117]. Results from both the DNS and the ROM show that low values of the overall dissipation are observed in the case of fluids made of simple molecules, e.g., air, and if the fluid is at a thermodynamic state in the proximity of that of the vapor–liquid critical point.
- Open Access
- 28 October 2023
- Published by Elsevier in Computers & Fluids
- Vol. 268
High fidelity simulation of dense vapours with thermodynamic consistent modelling
- 28 October 2023
- Published by Elsevier in Computers & Fluids
- Vol. 268
Open AccessHigh fidelity simulation of dense vapours with thermodynamic consistent modelling
- 2 May 2023
- Published by Springer Nature
- p. 62-71
High Fidelity Simulations and Modelling of Dissipation in Boundary Layers of Non-ideal Fluid Flows
- 2 May 2023
- Published by Springer Nature
- p. 62-71
High Fidelity Simulations and Modelling of Dissipation in Boundary Layers of Non-ideal Fluid Flows
- 2 March 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (4) , 1-16
Importance of Nonequilibrium Modeling for Compressors
This paper investigates the importance of nonequilibrium boundary-layer modeling for three compressor blade geometries, using RANS and high-fidelity simulations. We find that capturing nonequilibrium effects in RANS is crucial to capturing the correct boundary-layer loss. This is because the production of turbulence within the nonequilibrium region affects both the loss generation in the nonequilibrium region, but also the final equilibrium state. We show that capturing the correct nonequilibrium behavior is possible by adapting industry standard models (in this case the k–ω SST model). We show that for the range of cases studied here, nonequilibrium effects can modify the trailing-edge momentum thickness by up to 40% and can change the trailing-edge shape factor from 1.8 to 2.1.
- 2 March 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (4) , 1-16
Importance of Nonequilibrium Modeling for Compressors
This paper investigates the importance of nonequilibrium boundary-layer modeling for three compressor blade geometries, using RANS and high-fidelity simulations. We find that capturing nonequilibrium effects in RANS is crucial to capturing the correct boundary-layer loss. This is because the production of turbulence within the nonequilibrium region affects both the loss generation in the nonequilibrium region, but also the final equilibrium state. We show that capturing the correct nonequilibrium behavior is possible by adapting industry standard models (in this case the k–ω SST model). We show that for the range of cases studied here, nonequilibrium effects can modify the trailing-edge momentum thickness by up to 40% and can change the trailing-edge shape factor from 1.8 to 2.1.
- 25 November 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (5) , 1-27
Unsteady Structure of Compressor Tip Leakage Flows
Direct numerical simulations (DNS) are performed of a cantilevered stator blade to identify the unsteady and turbulent flow structure within compressor tip flows. The simulations were performed with clearances of 1.6% and 3.2% of chord. The results show that the flow both within the gap and at the exit on the suction side highly unsteady phenomena controlled by fine-scale turbulent structures. The signature of the classical tip-leakage vortex is a consequence of time-averaging and does not exist in the true unsteady flow. Despite the complexity, we are able to replicate the flow within the tip gap using a validated quasi-three-dimensional (Q3D) model. This enables a wide range of Q3D DNS simulations to study the effects of blade tip corner radius and Reynolds number. Tip corner radius is found to radically alter the unsteady flow in the tip; it affects both separation bubble size and shape, as well as transition mechanisms in the tip flow. These effects can lead to variations in tip mass flow of up to 10% and a factor of 2 variation in dissipation within the tip gap.
- 25 November 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (5) , 1-27
Unsteady Structure of Compressor Tip Leakage Flows
Direct numerical simulations (DNS) are performed of a cantilevered stator blade to identify the unsteady and turbulent flow structure within compressor tip flows. The simulations were performed with clearances of 1.6% and 3.2% of chord. The results show that the flow both within the gap and at the exit on the suction side highly unsteady phenomena controlled by fine-scale turbulent structures. The signature of the classical tip-leakage vortex is a consequence of time-averaging and does not exist in the true unsteady flow. Despite the complexity, we are able to replicate the flow within the tip gap using a validated quasi-three-dimensional (Q3D) model. This enables a wide range of Q3D DNS simulations to study the effects of blade tip corner radius and Reynolds number. Tip corner radius is found to radically alter the unsteady flow in the tip; it affects both separation bubble size and shape, as well as transition mechanisms in the tip flow. These effects can lead to variations in tip mass flow of up to 10% and a factor of 2 variation in dissipation within the tip gap.
- 19 April 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 144 (10) , 1-13
Low Reynolds Number Effects on the Separation and Wake of a Compressor Blade
This paper investigates the surface boundary layer and wake development of a compressor blade at a range of low Reynolds number from 45,000 to 120,000. Experiments in a miniature linear compressor cascade facility have been performed with detailed surface pressure measurements and flow visualization to track variations in the separation bubble size. These have been combined with high-resolution pneumatic pressure and hot-wire probe traverses in the downstream wake. High-fidelity direct numerical simulations have been completed on the same compressor blade section across the same range of operating conditions. The results show that large laminar separation bubbles exist on both blade surfaces. As Reynolds number increases, these separation bubbles shorten in length and reduce in thickness. Correspondingly, the downstream wake narrows, although the peak wake loss coefficient remains approximately constant. As the Reynolds number is increased from 45,000 to 120,000, the bubble length on the suction side reduced from 48% to 28% chord and on the pressure side reduced from 35% to 20% chord, while the loss coefficient reduced from 9% to 5%. The flow features are examined further within the high-fidelity computations, which reveal the dependence of the wake turbulence on the laminar separation bubbles. The separation bubbles are found to generate turbulent kinetic energy, which convects downstream to form the outer part of wake. As Re increases, a shorter bubble produces less turbulence in the outer part of the boundary layer leading to a narrower wake. However, the trailing edge separation is largely independent of Reynolds number, leading to the constant peak loss coefficient observed. The overall loss is shown to vary linearly with the total turbulence production, and this depends on the size of the separation bubbles. Overall, this research provides new insight into the connection between the blade surface flow field and the wake characteristics at low Reynolds number. The findings suggest that changes that minimize the extent of the blade separation bubbles could provide significant improvements to both the steady and unsteady properties of the wake.
- 19 April 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 144 (10) , 1-13
Low Reynolds Number Effects on the Separation and Wake of a Compressor Blade
This paper investigates the surface boundary layer and wake development of a compressor blade at a range of low Reynolds number from 45,000 to 120,000. Experiments in a miniature linear compressor cascade facility have been performed with detailed surface pressure measurements and flow visualization to track variations in the separation bubble size. These have been combined with high-resolution pneumatic pressure and hot-wire probe traverses in the downstream wake. High-fidelity direct numerical simulations have been completed on the same compressor blade section across the same range of operating conditions. The results show that large laminar separation bubbles exist on both blade surfaces. As Reynolds number increases, these separation bubbles shorten in length and reduce in thickness. Correspondingly, the downstream wake narrows, although the peak wake loss coefficient remains approximately constant. As the Reynolds number is increased from 45,000 to 120,000, the bubble length on the suction side reduced from 48% to 28% chord and on the pressure side reduced from 35% to 20% chord, while the loss coefficient reduced from 9% to 5%. The flow features are examined further within the high-fidelity computations, which reveal the dependence of the wake turbulence on the laminar separation bubbles. The separation bubbles are found to generate turbulent kinetic energy, which convects downstream to form the outer part of wake. As Re increases, a shorter bubble produces less turbulence in the outer part of the boundary layer leading to a narrower wake. However, the trailing edge separation is largely independent of Reynolds number, leading to the constant peak loss coefficient observed. The overall loss is shown to vary linearly with the total turbulence production, and this depends on the size of the separation bubbles. Overall, this research provides new insight into the connection between the blade surface flow field and the wake characteristics at low Reynolds number. The findings suggest that changes that minimize the extent of the blade separation bubbles could provide significant improvements to both the steady and unsteady properties of the wake.