Gregory Lecrivain
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gregory Lecrivain has a total of 69 co-authors. Here are the top co-authors by number of shared publications:
- Uwe Hampel
Helmholtz-Zentrum Dresden - Rossendorf, Institute of Fluid Dynamics, Bautzner Landstraße 400, 01328 Dresden, Germany
16 shared publications Uwe Hampel
10 shared publications- Ryoichi Yamamoto
Department of Chemical Engineering, Kyoto University
4 shared publications - Takashi Taniguchi
Kyoto University
4 shared publications Pierre Lorenz
Leibniz-Institut für Oberflächenmodifizierung, Permoserstraße 15 , Leipzig 04315, Germany
3 shared publications- Theodoros Nestor Papapetrou
Institute of Fluid Dynamics, Helmholtz-Zentrum Dresden – Rossendorf, Dresden, Germany
3 shared publications
Latest Publications
- Open Access
- 4 August 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1) , 24029
Effect of filling degree on particle segregation in a rotating drum - an experimental and numerical study
Granular mixing, ubiquitous in industry, is difficult to observe. Ultrafast X-ray computed tomography is a relatively new technique that can be used to study rapid granular flows in opaque systems. A comparative study is here presented, where ultrafast X-ray computed tomography, camera and simulation with the Discrete Element Method are simultaneously used to investigate the radial segregation of 4-mm spherical polypropylene and glass beads in a rotating drum. The drum filling is varied from 20 to 50%. The granular flow and the associated segregation dynamics at the front-end wall and in the bulk are compared and good agreement among the three methods is found. Similar to unary systems, a transition from the rolling to the sliding regime, characterized by a critical dynamic angle of repose, is also reported.
- 4 August 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1) , 24029
Open AccessEffect of filling degree on particle segregation in a rotating drum - an experimental and numerical study
Granular mixing, ubiquitous in industry, is difficult to observe. Ultrafast X-ray computed tomography is a relatively new technique that can be used to study rapid granular flows in opaque systems. A comparative study is here presented, where ultrafast X-ray computed tomography, camera and simulation with the Discrete Element Method are simultaneously used to investigate the radial segregation of 4-mm spherical polypropylene and glass beads in a rotating drum. The drum filling is varied from 20 to 50%. The granular flow and the associated segregation dynamics at the front-end wall and in the bulk are compared and good agreement among the three methods is found. Similar to unary systems, a transition from the rolling to the sliding regime, characterized by a critical dynamic angle of repose, is also reported.
- Open Access
- 25 March 2026
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 508, 141872
An experimental approach to quantifying the inhaled aerosol dose by human participants
- 25 March 2026
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 508, 141872
Open AccessAn experimental approach to quantifying the inhaled aerosol dose by human participants
- Open Access
- 5 February 2025
- Published by Elsevier in Journal of Aerosol Science
- Vol. 185
Kinetic Monte Carlo photonic model to simulate the UV inactivation of airborne microorganisms
- 5 February 2025
- Published by Elsevier in Journal of Aerosol Science
- Vol. 185
Open AccessKinetic Monte Carlo photonic model to simulate the UV inactivation of airborne microorganisms
- 2 October 2024
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 480 (2299)
Self-folding of two-dimensional thin templates into pyramidal microstructures by a liquid drop: a numerical model
We present a numerical framework bringing together a structural and a surface-energy minimization model to compute nano- and microorigami self-folding processes, that are three-dimensional in nature. A liquid drop, initially at rest on the template, triggers the spontaneous folding and deforms dynamically with the template. As application, the self-folding of thin two-dimensional templates into pyramidal microstructures is simulated. Each template is composed of a fixed regular base connected to rigid triangular side panels by two elastic hinges. We presently determine the condition, at which the transition from partial to full drop encapsulation occurs. The present model makes use of phase fields to numerically represent the drop and the template. This allows to: (i) develop an efficient computational method, which incorporates time-derivative terms and (ii) study three-dimensional complex self-folding processes.
- 2 October 2024
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 480 (2299)
Self-folding of two-dimensional thin templates into pyramidal microstructures by a liquid drop: a numerical model
We present a numerical framework bringing together a structural and a surface-energy minimization model to compute nano- and microorigami self-folding processes, that are three-dimensional in nature. A liquid drop, initially at rest on the template, triggers the spontaneous folding and deforms dynamically with the template. As application, the self-folding of thin two-dimensional templates into pyramidal microstructures is simulated. Each template is composed of a fixed regular base connected to rigid triangular side panels by two elastic hinges. We presently determine the condition, at which the transition from partial to full drop encapsulation occurs. The present model makes use of phase fields to numerically represent the drop and the template. This allows to: (i) develop an efficient computational method, which incorporates time-derivative terms and (ii) study three-dimensional complex self-folding processes.
- Open Access
Simplified Beam Hardening Correction for Ultrafast X-ray CT Imaging of Binary Granular Mixtures
Ultrafast X-ray computed tomography is an advanced imaging technique for multiphase flows. It has been used with great success for studying gas–liquid as well as gas–solid flows. Here, we apply this technique to analyze density-driven particle segregation in a rotating drum as an exemplary use case for analyzing industrial particle mixing systems. As glass particles are used as the denser of two granular species to be mixed, beam hardening artefacts occur and hamper the data analysis. In the general case of a distribution of arbitrary materials, the inverse problem of image reconstruction with energy-dependent attenuation is often ill-posed. Consequently, commonly known beam hardening correction algorithms are often quite complex. In our case, however, the number of materials is limited. We therefore propose a correction algorithm simplified by taking advantage of the known material properties, and demonstrate its ability to improve image quality and subsequent analyses significantly.
Open AccessSimplified Beam Hardening Correction for Ultrafast X-ray CT Imaging of Binary Granular Mixtures
Ultrafast X-ray computed tomography is an advanced imaging technique for multiphase flows. It has been used with great success for studying gas–liquid as well as gas–solid flows. Here, we apply this technique to analyze density-driven particle segregation in a rotating drum as an exemplary use case for analyzing industrial particle mixing systems. As glass particles are used as the denser of two granular species to be mixed, beam hardening artefacts occur and hamper the data analysis. In the general case of a distribution of arbitrary materials, the inverse problem of image reconstruction with energy-dependent attenuation is often ill-posed. Consequently, commonly known beam hardening correction algorithms are often quite complex. In our case, however, the number of materials is limited. We therefore propose a correction algorithm simplified by taking advantage of the known material properties, and demonstrate its ability to improve image quality and subsequent analyses significantly.
- Open Access
- 1 March 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (3)
Equilibrium Taylor bubble in a narrow vertical tube with constriction
Air Taylor bubbles in a millichannel filled with water are characterized by an elongated shape, a bullet-shaped nose (head), and a comparatively flat tail. Many experimental and numerical investigations have been performed in the past. Yet, most of them consider Taylor bubbles in a straight channel with constant cross section. The effect of a local change in the channel geometry on both the bubble shape and the flow fields on each side of the gas–liquid interface is, however, difficult to predict. In this work, we present experimental data obtained in a vertical millichannel, where the flow is moderately obstructed by a constriction, whose ratio ranges from 10% to 36%. We find that the Taylor bubble takes an equilibrium position for downward liquid flow with 264.36 < Re < 529.67 and 264.36 < Re < 728.29 for 10.17% and 18.06% constriction ratios, respectively. In this area, an empirical correlation characterizing the bubble head is provided. Other flow regimes, such as bubble breakup, co- and countercurrent configurations, are identified and shown in the form of a regime map. The results, besides their relevance in process engineering, exhibit high reproducibility and will serve as a reference for future interface-resolving two-phase flow simulations.
- 1 March 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (3)
Open AccessEquilibrium Taylor bubble in a narrow vertical tube with constriction
Air Taylor bubbles in a millichannel filled with water are characterized by an elongated shape, a bullet-shaped nose (head), and a comparatively flat tail. Many experimental and numerical investigations have been performed in the past. Yet, most of them consider Taylor bubbles in a straight channel with constant cross section. The effect of a local change in the channel geometry on both the bubble shape and the flow fields on each side of the gas–liquid interface is, however, difficult to predict. In this work, we present experimental data obtained in a vertical millichannel, where the flow is moderately obstructed by a constriction, whose ratio ranges from 10% to 36%. We find that the Taylor bubble takes an equilibrium position for downward liquid flow with 264.36 < Re < 529.67 and 264.36 < Re < 728.29 for 10.17% and 18.06% constriction ratios, respectively. In this area, an empirical correlation characterizing the bubble head is provided. Other flow regimes, such as bubble breakup, co- and countercurrent configurations, are identified and shown in the form of a regime map. The results, besides their relevance in process engineering, exhibit high reproducibility and will serve as a reference for future interface-resolving two-phase flow simulations.
- 25 August 2023
- Published by Elsevier in Journal of Aerosol Science
- Vol. 174
Influence of engineered roughness microstructures on adhesion and turbulent resuspension of microparticles
- 25 August 2023
- Published by Elsevier in Journal of Aerosol Science
- Vol. 174
Influence of engineered roughness microstructures on adhesion and turbulent resuspension of microparticles
- Open Access
- 8 December 2022
- Published by Springer Nature in Environmental Fluid Mechanics
- Vol. 23 (1) , 41-63
Simulation of particle resuspension by wind in an urban system
- 8 December 2022
- Published by Springer Nature in Environmental Fluid Mechanics
- Vol. 23 (1) , 41-63
Open AccessSimulation of particle resuspension by wind in an urban system
- 3 August 2021
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 6 (8) , L082301
Evidence of collision-induced resuspension of microscopic particles from a monolayer deposit
The present Letter addresses the resuspension of microscopic glass particles from a monolayer bed into a turbulent gas flow. With an intermediate surface coverage, here set to about of the field of view, we report two distinct detachment mechanisms. At relatively low flow velocities, few loosely adhering particles move on the wall to eventually collide with neighboring particles resulting in a clustered resuspension. At higher fluid velocities, mostly individual particles resuspend due to their interaction with the turbulent flow. The resuspension curve, showing the remaining particle fraction as a function of the flow velocity, exhibits a strong bimodal character.- 3 August 2021
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 6 (8) , L082301
Evidence of collision-induced resuspension of microscopic particles from a monolayer deposit
The present Letter addresses the resuspension of microscopic glass particles from a monolayer bed into a turbulent gas flow. With an intermediate surface coverage, here set to about of the field of view, we report two distinct detachment mechanisms. At relatively low flow velocities, few loosely adhering particles move on the wall to eventually collide with neighboring particles resulting in a clustered resuspension. At higher fluid velocities, mostly individual particles resuspend due to their interaction with the turbulent flow. The resuspension curve, showing the remaining particle fraction as a function of the flow velocity, exhibits a strong bimodal character.- Open Access
- 24 July 2021
- Published by Springer Nature in Rheologica Acta
- Vol. 60 (10) , 587-601
A computational method to simulate mono- and poly-disperse two-dimensional foams flowing in obstructed channel
- 24 July 2021
- Published by Springer Nature in Rheologica Acta
- Vol. 60 (10) , 587-601
Open AccessA computational method to simulate mono- and poly-disperse two-dimensional foams flowing in obstructed channel